molecalculator

Moles & Molar Mass

First-Order vs Zero-Order Kinetics Graphs Explained

Guide 01-6539 · Updated · Step by step

A first-order kinetics graph is linear when you plot the natural logarithm of reactant concentration against time; a zero-order graph is linear when you plot concentration directly against time. Their slopes differ too: first order has slope −k, while zero order has slope −k, but the rate constant has different units in each case.

What the Graphs Show

A kinetics graph shows how a reactant’s concentration changes as a reaction proceeds. To identify reaction order, compare concentration-versus-time data with the integrated rate laws—not merely the shape of a curve on one arbitrarily chosen graph.

  • Zero order: plot [A] against time, t. The ideal result is a straight line descending with slope −k.
  • First order: plot ln[A] against time, t. The ideal result is a straight line descending with slope −k.

Here, [A] is the concentration of reactant A, usually in mol/L, and t is time. The shared symbol k does not mean that the two rate constants are interchangeable: their dimensions depend on the reaction order.

Rate Laws and Linear Forms

The rate law describes how the instantaneous rate depends on reactant concentration. For a single reactant, a zero-order law is rate = −d[A]/dt = k. Integrating gives [A]t = [A]0 − kt. This has the form y = b + mx, so a plot of [A]t against t has intercept [A]0 and slope −k.

For a first-order reaction, rate = −d[A]/dt = k[A]. Integration gives ln([A]t/[A]0) = −kt, or ln[A]t = ln[A]0 − kt. Plot ln[A]t against t: its intercept is ln[A]0 and its slope is −k.

Concentration must be positive to take its logarithm. The logarithm is of a concentration value expressed consistently; changing concentration units shifts the intercept but not the slope, provided the same units are used throughout. In practice, log10[A] can also be plotted, but its slope is −k/2.303, rather than −k.

How to Read the Slopes and Units

The slope of the appropriate straight-line plot gives the rate constant. A negative slope reflects reactant consumption. Report the magnitude as a positive k, unless a question specifically asks for the plotted slope.

  • For zero order, k has concentration/time units, such as mol L−1 s−1.
  • For first order, k has inverse-time units, such as s−1.

For example, a first-order ln[A]-versus-time slope of −0.020 s−1 corresponds to k = 0.020 s−1. A zero-order [A]-versus-time slope of −0.020 mol L−1 s−1 corresponds to k = 0.020 mol L−1 s−1. The numerical slopes match here, but their units—and the underlying kinetics—do not.

Choosing a Plot and Testing Reaction Order

With concentration measurements at several times, make the candidate plots and assess which is most nearly linear. A practical comparison is to examine residuals (differences between observed and fitted values) and whether the pattern shows systematic curvature, rather than relying only on a high R2. An apparently high R2 alone does not prove a kinetic model.

  1. Record time and reactant concentration, keeping units and measurement conditions consistent.
  2. Plot [A] against time for the zero-order model.
  3. Plot ln[A] against time for the first-order model.
  4. Fit a straight line to each candidate and inspect residuals and the experimental context.
  5. Use the model supported by the evidence; calculate k from its slope and state the units.

If several reactants are involved, a simple plot against time may not identify the full rate law. Initial-rate experiments, isolation methods, or a mechanistic model may be needed to determine how the rate depends on each reactant.

Half-Life and Concentration-Time Curves

Half-life is another useful distinction. For a first-order reaction, t1/2 = ln 2/k, so it is constant regardless of the starting concentration under the same conditions. For a zero-order reaction, t1/2 = [A]0/(2k), so it depends on the initial concentration. The zero-order integrated equation reaches [A] = 0 at t = [A]0/k; beyond that point, the equation cannot describe a negative physical concentration.

On a direct concentration-versus-time graph, zero-order consumption is a straight descending line. First-order consumption instead curves downward and approaches zero asymptotically. On a semilog plot—ln[A] versus time—the first-order data become linear. These descriptions are not contradictory; the chosen axes determine which model appears as a straight line.

Common Misreadings and Limits

  • Confusing slope signs: the reactant concentration falls, so the fitted slope is negative; k is conventionally positive.
  • Mixing up logarithms: natural-log plots have slope −k. Base-10 logarithm plots have slope −k/2.303.
  • Ignoring units: a zero-order k and a first-order k have different dimensions.
  • Calling every straight graph proof: data over a limited time range can look linear by chance, and experimental uncertainty matters.
  • Assuming order from the equation alone: reaction order is generally determined experimentally; it is not automatically read from the balanced chemical equation.

Reaction order can also be conditional. A reaction that is first order in a reactant over one concentration range may show a different apparent order when a catalyst is saturated, a surface is filled, or another step limits the rate. Temperature, solvent, pH, and other conditions can affect measured kinetics, so quote the conditions alongside k.

Frequently Asked Questions

Which graph is linear for a first-order reaction?
Plot ln[A] against time. The integrated first-order rate law predicts a straight line with slope −k.

Which graph is linear for a zero-order reaction?
Plot [A] directly against time. The slope is −k and the intercept is the initial concentration.

Can I use log instead of ln?
Yes, but identify which logarithm is used. With log10[A], the slope is −k/2.303; with ln[A], it is −k.

How can I tell whether data are first or zero order?
Compare the linearity and residual patterns of [A] versus time and ln[A] versus time, using enough measurements and considering experimental uncertainty.

Why do the rate constants have different units?
Because the rate law contains different powers of concentration. Zero-order k has concentration/time units; first-order k has inverse-time units.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →