molecalculator

Moles & Molar Mass

Decay Over Time Formula: Exponential Decay Calculator

Calculator No. 01-4468 · Updated · Formula and assumptions shown below

Amount remaining 36.7879 units
Percentage remaining
36.79 %
Result, rounded to 2 decimal places
Starting amount
100 units
Set in the form below
Decay constant
0.1 1/time
Set in the form below
You enter
Starting amount (units), Decay constant (1/time), Elapsed time (time units)
You get
Amount remaining (units), Percentage remaining (%)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The standard formula for decay over time is Q(t) = Q₀e−kt, where Q₀ is the starting amount, k is the decay constant, and t is elapsed time in matching units. This calculator estimates the amount remaining from those values; enter the starting amount, decay constant, and time to get the remaining amount and percentage left.

Formula

The exponential decay equation is:

Q(t) = Q₀e−kt

  • Q(t) is the amount remaining after time t, in the same units as the starting amount.
  • Q₀ is the initial amount at time zero.
  • e is Euler’s number, approximately 2.71828.
  • k is the nonnegative decay constant, expressed as the inverse of the time unit (for example, day−1).
  • t is elapsed time in the time unit used to specify k.

The calculator’s second result is the percentage remaining: 100e−kt. The amount lost is Q₀ − Q(t), or 100% minus the percentage remaining. The exponent kt must be dimensionless, so the time units must match: if k is per day, enter elapsed time in days.

Worked Example

Using the calculator defaults, the starting amount is 100 units, the decay constant is 0.1 per time unit, and elapsed time is 10 time units.

  1. Multiply the decay constant by elapsed time: kt = 0.1 × 10 = 1.
  2. Find the amount remaining: Q(t) = 100 × e−1 = 36.7879, which rounds to 36.7879 units.
  3. Find the percentage remaining: 100 × e−1 = 36.7879%, which rounds to 36.79%.

So about 36.79 units remain, and about 63.21 units have decayed or otherwise been removed from the measured amount under this model.

Assumptions

  • The amount follows continuous, first-order exponential decay with a constant k.
  • The decay constant and elapsed time use reciprocal, matching time units.
  • The starting amount and calculated remainder are measured on the same basis; the model does not account for additions, changing conditions, or measurement error.

How Exponential Decay Works

In a first-order process, the rate of decrease at any moment is proportional to the amount currently present. When more remains, the absolute decrease per unit time is larger; as the amount falls, the decrease slows. The differential equation is dQ/dt = −kQ. Solving it gives the exponential formula above. Because an exponential approaches zero without reaching it at any finite time, the ideal model predicts a positive remainder for any finite elapsed time when the starting amount is positive.

“Decay” can refer to different real-world processes, including radioactive decay, loss of a chemical concentration, or depreciation in a simplified model. The same mathematical shape may describe these processes, but their mechanisms and interpretations differ. A calculator result is a mathematical estimate, not evidence that a particular substance or system actually follows this model.

Half-Life and Other Useful Forms

Half-life is the time required for an amount to fall to half its starting value. Set Q(t)/Q₀ = 1/2 in the exponential equation:

t1/2 = ln(2)/k

Conversely, if half-life is known, use k = ln(2)/t1/2. The half-life and the time unit must agree. For example, a half-life stated in hours gives a decay constant in inverse hours. After one half-life, 50% remains; after two, 25%; after three, 12.5%. Equal time intervals remove equal fractions of what remains, not equal absolute amounts.

If you know two measurements instead of the decay constant, with Q₁ at time t₁ and Q₂ at a later time t₂, estimate the constant using k = ln(Q₁/Q₂)/(t₂ − t₁), provided both amounts are positive and the same first-order process applies throughout the interval.

Choosing Inputs and Reading Results

  • Starting amount: Use the value at the chosen time zero, such as an initial mass, count, or concentration. The calculator keeps its units for the result.
  • Decay constant: Use a value appropriate to the process and conditions. It must be nonnegative and expressed per unit time.
  • Elapsed time: Enter a nonnegative duration in the matching time unit. Convert it first if necessary; for instance, 30 days is not 30 years.
  • Remaining percentage: A value of 100% means none has been lost, while 25% means three quarters of the initial amount is no longer present under the model.

The decay constant is not itself a percentage. For a small time interval, a constant of 0.1 per day corresponds approximately to a 10% decrease during one day, but the exact continuous-model fraction remaining after one day is e−0.1, or about 90.48%. The exact loss is about 9.52%, because the rate acts on a continually changing amount.

Limits and Common Mistakes

The main error is mixing time units. Substituting years into a constant measured per day makes the exponent wrong by a large factor. Another common mistake is treating “decay constant” as a percentage per interval without converting it to a first-order constant. If measurements show a fixed amount disappearing per interval rather than a fixed fraction of what remains, a linear model may be more appropriate than exponential decay.

Real data may depart from a single exponential because the decay rate changes, multiple processes operate, the system receives new material, or measurements are noisy. For radioactive nuclides, the exponential law describes the statistical behavior of a large population; it does not predict the exact decay time of an individual nucleus. For chemical or environmental quantities, verify whether first-order kinetics and constant conditions are justified before interpreting the estimate.

Rounding also matters. Keep extra digits in intermediate calculations and round only the reported result. When the exponent is very negative, the remainder may be extremely small; a displayed zero can reflect rounding or limited numerical precision rather than a literal finite-time disappearance.

Frequently Asked Questions

What is the formula for decay over time?
For first-order exponential decay, use Q(t) = Q₀e−kt. It gives the amount remaining after elapsed time t.

How do I calculate the decay constant from half-life?
Use k = ln(2)/t1/2. The resulting constant is in the inverse of the half-life’s time unit.

How do I find the time needed to reach a target amount?
Rearrange the equation to t = ln(Q₀/Q)/k, where Q is the target remaining amount. This applies when 0 < Q ≤ Q₀ and k > 0.

Does exponential decay ever reach zero?
In the ideal mathematical model, it approaches zero but does not reach exactly zero in finite time. Practical measurements can nevertheless fall below a detection limit.

Is decay always exponential?
No. Exponential decay fits processes where the rate is proportional to the amount remaining and the rate constant stays fixed. A different pattern of measurements may need a different model.

Related

Formula used
in q0 | Starting amount | units | 100 | 0
in k | Decay constant | 1/time | 0.1 | 0
in t | Elapsed time | time units | 10 | 0
out q | Amount remaining | units | q0 * exp(-k * t) | 4
out p | Percentage remaining | % | 100 * exp(-k * t) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →