The enthalpy of vaporization (ΔHvap) is the heat required to convert one mole of a liquid into vapor at constant pressure. The basic formula is ΔHvap = q / n, where q is the heat absorbed and n is the number of moles. For temperature-dependent calculations, the Clausius–Clapeyron equation gives ln(P₂/P₁) = –(ΔHvap/R)(1/T₂ – 1/T₁).
Formula
At constant pressure, the enthalpy of vaporization is defined as:
ΔHvap = q / n
- ΔHvap – enthalpy of vaporization (J/mol or kJ/mol)
- q – heat absorbed by the liquid (J or kJ)
- n – amount of substance vaporized (mol), n = m / M
- m – mass of liquid vaporized (g)
- M – molar mass (g/mol)
For the temperature dependence of vapor pressure, the Clausius–Clapeyron equation is:
ln(P₂ / P₁) = –(ΔHvap / R) × (1/T₂ – 1/T₁)
- P₁, P₂ – vapor pressures at temperatures T₁ and T₂ (any consistent pressure unit)
- T₁, T₂ – absolute temperatures (K)
- R – gas constant, 8.314 J/(mol·K)
This equation assumes the vapor behaves ideally and that ΔHvap is constant over the temperature range.
Worked Example
Using the default values: m = 18.015 g (1 mole of water), M = 18.015 g/mol, q = 40,660 J (the heat needed to vaporize 1 mole of water at 100 °C).
Step 1: Calculate moles of water.
n = m / M = 18.015 g / 18.015 g/mol = 1.0000 mol
Step 2: Calculate ΔHvap.
ΔHvap = q / n = 40,660 J / 1.0000 mol = 40,660 J/mol
Step 3: Convert to kJ/mol.
ΔHvap = 40,660 J/mol / 1000 = 40.66 kJ/mol
The calculator returns 40660.0 J/mol and 40.66 kJ/mol.
Assumptions
- The process occurs at constant pressure (usually 1 atm).
- The vapor is treated as an ideal gas (for Clausius–Clapeyron).
- ΔHvap is constant over the temperature range used.
- No heat is lost to the surroundings.
- The liquid is pure (no solute effects).
Why Enthalpy of Vaporization Matters
Every liquid has a characteristic ΔHvap that reflects the strength of intermolecular forces. Water has a high value (40.66 kJ/mol at 100 °C) because of hydrogen bonding. Nonpolar liquids like hexane have lower values (about 28.9 kJ/mol at its boiling point). This property explains why sweating cools the body, why steam burns are so severe, and why distillation separates mixtures.
In industry, ΔHvap is used to size heat exchangers, design condensers, and calculate energy costs for evaporation processes. In the lab, it helps predict how much heat a reaction will absorb if a solvent evaporates.
How to Use the Enthalpy of Vaporization Formula
The direct formula ΔHvap = q / n is used when you measure the heat input and the amount of liquid vaporized. In a typical calorimetry experiment:
- Weigh a liquid sample and record its mass.
- Heat it to boiling and measure the heat added (q) with a joulemeter or from electrical power (P × time).
- Measure the mass of liquid that actually vaporizes (final mass – initial mass).
- Convert mass to moles using molar mass.
- Divide q by moles to get ΔHvap.
For the Clausius–Clapeyron equation, you need vapor pressure data at two temperatures. This is common when you only have a boiling point at one pressure and want to estimate the boiling point at another (e.g., high-altitude cooking).
Common Mistakes and Misconceptions
- Using Celsius instead of Kelvin: Always convert °C to K by adding 273.15. Using Celsius in the Clausius–Clapeyron equation gives a completely wrong result.
- Confusing ΔHvap with specific heat: Specific heat (c) warms the liquid without changing phase; ΔHvap changes phase at constant temperature.
- Forgetting that ΔHvap varies with temperature: The value at the normal boiling point is often quoted, but it decreases as temperature increases. At the critical point, it becomes zero.
- Mixing up J/mol and kJ/mol: Always check units. 40.66 kJ/mol = 40,660 J/mol.
- Assuming vapor is ideal: At high pressures or near the critical point, real gases deviate, and the Clausius–Clapeyron equation becomes inaccurate.
Comparing Enthalpies of Vaporization
Substances with strong intermolecular forces have higher ΔHvap. Here are typical values at the normal boiling point:
- Water (H₂O): 40.66 kJ/mol
- Ethanol (C₂H₅OH): 38.56 kJ/mol
- Methanol (CH₃OH): 35.21 kJ/mol
- Hexane (C₆H₁₄): 28.85 kJ/mol
- Diethyl ether: 26.52 kJ/mol
- Nitrogen (N₂): 5.57 kJ/mol
Notice that hydrogen-bonded liquids (water, alcohols) have higher values than nonpolar ones. Small molecules with weak dispersion forces (N₂) have very low values.
Using the Clausius–Clapeyron Equation
Suppose you know that water boils at 100 °C (373.15 K) at 1 atm (101.325 kPa). What is the vapor pressure at 80 °C (353.15 K)? Rearranging:
ln(P₂ / 101.325) = –(40,660 / 8.314) × (1/353.15 – 1/373.15)
Calculate the right side:
1/353.15 = 0.0028317, 1/373.15 = 0.0026800, difference = 0.0001517
–(40,660 / 8.314) × 0.0001517 = –4890.5 × 0.0001517 = –0.7418
So ln(P₂ / 101.325) = –0.7418, thus P₂ / 101.325 = e^(–0.7418) = 0.4762
P₂ = 101.325 × 0.4762 = 48.3 kPa
This matches the known vapor pressure of water at 80 °C (about 47.4 kPa; the small difference is due to ΔHvap varying with temperature).
Limitations and Real-World Considerations
The simple formulas assume ideal behavior. In reality, ΔHvap depends on temperature and pressure. At higher temperatures, the vapor is denser and the intermolecular forces in the liquid are weaker, so less heat is needed to escape. The enthalpy of vaporization at any temperature can be estimated with Watson’s correlation, but that requires the critical temperature and an exponent.
For mixtures, the enthalpy of vaporization is not simply the weighted average of the components; it depends on the composition of the vapor and liquid phases. In such cases, you need experimental data or a thermodynamic model.
Also, the Clausius–Clapeyron equation is most accurate when the temperature range is small (a few tens of degrees) and the pressure is well below the critical pressure.
Safety and Practical Notes
When measuring heat of vaporization, always work in a well-ventilated area, especially with volatile organic solvents. Use appropriate personal protective equipment (goggles, gloves). Follow your lab method, the safety data sheet (SDS) and your supervisor. Never heat a closed container – pressure buildup can cause explosions. When using electrical heaters, ensure they are rated for the solvent and that the apparatus is grounded.
Frequently Asked Questions
What is the difference between enthalpy of vaporization and heat of vaporization?
They are the same thing. “Heat of vaporization” is the older term; “enthalpy of vaporization” is more precise because it accounts for pressure–volume work. In practice, both refer to the heat absorbed per mole (or per gram) during vaporization at constant pressure.
Why does water have such a high enthalpy of vaporization?
Water molecules form strong hydrogen bonds. To escape into the vapor phase, each molecule must break roughly two hydrogen bonds. This requires a lot of energy compared to nonpolar liquids where only weak London dispersion forces are present.
How do I convert enthalpy of vaporization from J/mol to kJ/kg?
First convert J/mol to kJ/mol (divide by 1000), then divide by the molar mass in kg/mol. For water: 40.66 kJ/mol ÷ 0.018015 kg/mol = 2257 kJ/kg. This is the same as 2,257,000 J/kg.
Does enthalpy of vaporization change with pressure?
Yes, it decreases as pressure increases. At higher pressure, the boiling point is higher, and the liquid is closer to the critical point, so less additional energy is needed to vaporize it. At the critical point, the enthalpy of vaporization is zero.
Can I use the Clausius–Clapeyron equation for any substance?
It works well for pure substances over a moderate temperature range where the vapor behaves ideally. It fails near the critical point or when the substance dimerizes in the vapor (e.g., acetic acid). For such cases, more advanced equations are needed.
What is the enthalpy of vaporization of water at 25 °C?
At 25 °C (298.15 K), the enthalpy of vaporization of water is about 43.99 kJ/mol (or 2442 kJ/kg). It is higher than at 100 °C because the liquid is further from the boiling point, so more energy is needed to break intermolecular bonds.
Related
Formula used
in m | Mass of liquid | g | 18.015 | 0 in mm | Molar mass | g/mol | 18.015 | 0.001 in q | Heat added | J | 40660 | 0 out dh | Enthalpy of vaporization | J/mol | q / (m / mm) | 1 out dhk | Enthalpy of vaporization | kJ/mol | dh / 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check