molecalculator

Moles & Molar Mass

Ft-lb to Joules Formula and Conversion

Calculator No. 01-4695 · Updated · Formula and assumptions shown below

Energy 13.558 J
Energy
0.01356 kJ
= Energy ÷ 1000
Energy
10 ft-lb
Set in the form below
You enter
Energy (ft-lb)
You get
Energy (J), Energy (kJ)
Rounding
3 dp · 5 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To convert foot-pounds (ft-lb) to joules (J), multiply the value in foot-pounds by 1.355817948. This calculator takes an energy value in ft-lb and returns joules, using the international definition of the foot and the exact SI joule.

Formula

J = ft-lb × 1.355817948

Here, ft-lb is the energy in foot-pounds, and J is the equivalent energy in joules. The conversion factor follows from the international foot: 1 foot = 0.3048 metres exactly, and 1 pound-force = 4.4482216152605 newtons. Since 1 joule equals 1 newton-metre, one foot-pound is 0.3048 × 4.4482216152605 = 1.355817948 joules when the factor is rounded to the displayed digits. The calculator also shows the result in kilojoules, where 1 kJ = 1,000 J.

Worked Example

Using the calculator’s default input of 10 ft-lb:

  1. Multiply by the conversion factor: 10 ft-lb × 1.355817948 J/ft-lb = 13.55817948 J.
  2. Rounded to the calculator’s three decimal places, the result is 13.558 J.
  3. Convert joules to kilojoules: 13.55817948 J / 1000 = 0.01355817948 kJ, or 0.01356 kJ to five decimal places.

Assumptions

  • The input is a mechanical energy or work value expressed in foot-pounds, not torque in pound-feet.
  • The conversion uses the international foot and pound-force definitions.
  • The displayed factor is rounded to nine decimal places; results may differ in the final digits if a source uses a more precise factor or rounds at a different step.

When to Use This Conversion

Foot-pounds are used in some engineering, mechanics, and equipment specifications, while joules are the SI unit for energy and work. Converting units is useful when comparing values reported in different systems, entering data into a calculation that requires joules, or interpreting a mechanical energy figure alongside SI measurements.

A foot-pound of work describes one pound-force acting through one foot in the direction of that force. The joule expresses the same physical quantity in SI terms: one joule is the work done by a one-newton force acting through one metre. The conversion changes the unit, not the physical energy represented.

  • Use the calculator when you have an energy value in ft-lb and need joules or kilojoules.
  • Keep the units attached when recording a result; a bare number can be mistaken for a value in another unit.
  • Retain extra digits during multi-step calculations, then round the final answer to the precision justified by the original measurement.

What “Foot-Pound” Means

The notation ft-lb is commonly used for foot-pound, a unit of work or energy. In this context, “pound” means pound-force, not pound-mass. A pound-mass is a measure of mass; a pound-force is a force. Work is calculated as force multiplied by displacement in the direction of the force, so a force unit and a distance unit combine to give energy.

In technical writing, pound-foot (lb-ft) is often used for torque, while foot-pound (ft-lb) is often used for work or energy. Their dimensions are equivalent—force multiplied by distance—but the quantities are not interchangeable in meaning. Torque describes a turning effect around an axis; energy describes the capacity to do work. Always follow the context and unit convention of the specification you are reading.

Conversion Examples and Reverse Calculation

For a quick estimate, 1 ft-lb is about 1.356 J. For a more accurate conversion, use the full factor shown in the calculator. For example, 25 ft-lb is 25 × 1.355817948 = 33.8954487 J, approximately 33.895 J. A value of 100 ft-lb is 135.5817948 J, approximately 135.582 J.

To convert in the opposite direction, divide joules by the same factor:

ft-lb = J / 1.355817948

For example, 50 J / 1.355817948 ≈ 36.873 ft-lb. Multiplication converts ft-lb to joules; division converts joules to ft-lb. Reversing these operations is a useful way to check that the direction of conversion is correct.

Accuracy, Rounding, and Common Mix-Ups

The conversion factor is not the main source of uncertainty in most practical values. The measured or specified input may itself be rounded, estimated, or reported with limited precision. If a measurement is given as 10 ft-lb, reporting a result such as 13.558179480 J can imply more certainty than the original figure supports. Use the calculator’s digits for arithmetic, but choose final rounding based on the source data and purpose.

  • Do not multiply by 1,000. That factor converts joules to millijoules or kilojoules in the opposite direction; ft-lb to J uses about 1.356.
  • Do not confuse ft-lb with lb-ft. The same dimensions may appear in torque specifications, but torque and energy describe different physical quantities.
  • Do not confuse pound-force with pound-mass. The conversion factor applies to force-distance work, not a mass-distance product.
  • Check the sign and context. The calculator accepts nonnegative energy magnitudes. In a larger physics problem, signed work can be negative when the force acts opposite the displacement; interpret that sign using the problem’s convention.

Frequently Asked Questions

How many joules are in 1 ft-lb?
One foot-pound is approximately 1.355817948 joules. For ordinary estimates, 1.356 J per ft-lb is usually sufficient.

What is the formula for ft-lb to joules?
Multiply the foot-pound value by 1.355817948: J = ft-lb × 1.355817948.

How do I convert joules back to ft-lb?
Divide the joule value by 1.355817948. For example, 100 J is about 73.756 ft-lb.

Are ft-lb and lb-ft the same?
Their units have the same force-times-distance dimensions, but usage often distinguishes energy (ft-lb) from torque (lb-ft). Check what quantity the value describes rather than relying on the letters alone.

Is a foot-pound a unit of torque or energy?
It is commonly used for energy or work, while pound-foot is commonly used for torque. Both involve force and distance, but the physical meanings differ.

Related

Formula used
in ftlb | Energy | ft-lb | 10 | 0
out j | Energy | J | ftlb * 1.355817948 | 3
out kj | Energy | kJ | j / 1000 | 5

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →