molecalculator

Moles & Molar Mass

Gas Flow Cv Equation: Formula and Sizing

Calculator No. 01-4682 · Updated · Formula and assumptions shown below

Gas flow 2,440.94 scfh
Pressure-drop ratio
0.1000
= (Upstream absolute pressure − Downstream absolute pressure) ÷ Upstream absolute pressure
Valve flow coefficient Cv
1 US gpm / sqrt(psi)
Set in the form below
Upstream absolute pressure
100 psia
Set in the form below
You enter
Valve flow coefficient Cv (US gpm / sqrt(psi)), Upstream absolute pressure (psia), Downstream absolute pressure (psia), Gas temperature (°F), Gas specific gravity relative to air
You get
Gas flow (scfh), Pressure-drop ratio
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The gas-flow Cv equation estimates the standard volumetric flow of a gas through a control valve from its Cv, upstream pressure, temperature, and gas properties. Enter those values to calculate flow; the result is an estimate under the equation’s stated pressure and flow conventions, not a complete valve-selection recommendation.

Formula

This calculator uses the common ISA-style sizing relation for subcritical gas flow through a valve, expressed in U.S. customary units:

Q = 136.3 Cv P₁ √[ (P₁ − P₂) / (Gg T) ]

  • Q is standard gas flow in standard cubic feet per hour (scfh).
  • Cv is the valve flow coefficient, conventionally defined as the U.S. gallons per minute of water at 60 °F that produce a 1 psi pressure drop.
  • P₁ is upstream absolute pressure in psia.
  • P₂ is downstream absolute pressure in psia.
  • Gg is gas specific gravity relative to air, dimensionless.
  • T is absolute gas temperature in degrees Rankine. The calculator converts the entered °F value by adding 459.67.

The coefficient 136.3 belongs to this particular customary-unit convention and standard-flow basis. It must not be carried over unchanged to SI units or a different definition of standard conditions. The equation assumes a subcritical pressure drop; it does not include the valve’s pressure-recovery factor, piping geometry factor, or other corrections used in detailed sizing standards. The displayed pressure-drop ratio is x = (P₁ − P₂) / P₁.

Worked Example

Using the block’s default values: Cv = 1, P₁ = 100 psia, P₂ = 90 psia, gas temperature = 60 °F, and Gg = 0.6:

  1. Convert temperature to Rankine: T = 60 + 459.67 = 519.67 °R.
  2. Find the pressure difference: P₁ − P₂ = 100 − 90 = 10 psi.
  3. Calculate the pressure-drop ratio: x = 10 / 100 = 0.1000.
  4. Substitute: Q = 136.3 × 1 × 100 × √[10 / (0.6 × 519.67)].
  5. The square-root term is approximately 0.17910, so Q ≈ 2440.1 scfh.

The output is therefore 2440.10 scfh to two decimal places. This is a nominal calculation, not a guarantee of actual flow through a particular installed valve.

Assumptions

  • Gas specific gravity is relative to air under the convention used by the applicable valve-sizing method.
  • Pressures entered are absolute, not gauge pressures.
  • Temperature is uniform and is converted from °F to °R using +459.67.
  • The flow is subcritical and the chosen standard-volume reference matches the coefficient convention.
  • The simplified equation omits valve-specific and installation corrections; use the manufacturer’s certified sizing method for selection.

How the Equation Works

The valve coefficient represents a standardized measure of a valve’s capacity. In the gas equation, larger Cv increases predicted flow proportionally. A larger upstream pressure also tends to increase flow, while a larger pressure difference increases the square-root term. Higher temperature or higher gas specific gravity reduces the predicted standard flow for the same Cv and pressures.

“Standard” flow is a volume rate referred to specified reference conditions, rather than the volume occupying the pipe at the actual operating pressure and temperature. Standard conditions are not universal: organizations and industries may define different reference temperatures and pressures. Check the convention behind the coefficient, instrument, or data sheet before comparing scfh values. Actual volume in a line can differ substantially from standard volume.

When to Use It and What to Check

This equation is useful for a preliminary estimate, checking the scale of a published gas-flow value, or understanding how pressure, temperature, gas density, and Cv affect capacity. It is not enough by itself to choose a control valve. For selection, a recognized sizing procedure uses the valve’s pressure-recovery characteristics and may account for attached fittings, piping reducers, compressibility, and operating regime.

  • Confirm that the Cv is for the relevant valve and opening or travel. A valve’s maximum Cv may not represent its capacity at normal operating position.
  • Use absolute pressure. For pressure reported as psig, add local atmospheric pressure to obtain psia; do not insert psig directly.
  • Use the gas’s specific gravity relative to air, not its density in unrelated units. If the gas composition or molecular weight varies, the assumed value may not represent the stream.
  • Use the actual gas temperature in °F and ensure it is above absolute zero, −459.67 °F.
  • Check that P₁ exceeds P₂. Equal pressures imply no pressure-driven flow in this model; a downstream pressure above upstream pressure is outside the intended calculation.
  • Verify the standard-condition basis and the units of Cv before interpreting the result.

Limits, Choked Flow, and Common Mistakes

The main limitation is that gas flow can become choked: once the pressure ratio crosses a valve-dependent threshold, reducing downstream pressure further does not produce the increase predicted by the simple square-root relation. A common rough screening indicator is the pressure-drop ratio x = (P₁ − P₂) / P₁, but there is no single universal cutoff for all valves. Detailed methods use a pressure-drop factor such as xT, supplied for the valve, to identify and calculate choked flow. Do not treat this calculator’s result as valid for a choked condition.

Another frequent error is mixing absolute and gauge pressure. For example, 20 psig is not 20 psia; near sea level it is roughly 34.7 psia. Since pressure appears directly and inside the pressure-drop term, that mistake can materially distort the answer. Mixing °F with an absolute-temperature formula is also incorrect: the equation requires Rankine, which is why the conversion adds 459.67.

Finally, Cv values and flow coefficients are unit-system dependent. Do not enter a metric Kv value as though it were Cv. A commonly used approximate conversion is Cv ≈ 1.156 Kv, but confirm the coefficient definition and applicable standard before using it. Rounding inputs early can also affect results, especially when the pressure drop is small.

Frequently Asked Questions

What is the gas-flow Cv equation?
The simplified subcritical relation is Q = 136.3 Cv P₁ √[(P₁ − P₂)/(Gg T)] for flow in scfh with Cv in its customary U.S. definition, pressures in psia, and temperature in °R.

Does the gas-flow equation use psig or psia?
Use absolute pressure, psia. Convert a gauge reading by adding local atmospheric pressure; the exact conversion depends on local atmospheric conditions.

What does Cv mean for a valve?
Cv is a standardized water-flow coefficient: the U.S. gallons per minute of water at 60 °F that pass with a 1 psi pressure drop under the coefficient’s conventional test definition.

Can I use this equation for choked gas flow?
No. The simplified equation does not account for the valve-specific choked-flow limit. Use a recognized sizing method with the valve’s pressure-recovery data.

Is scfh the same as actual cubic feet per hour?
No. Scfh expresses flow at stated standard reference conditions; actual cubic feet per hour describes volume at operating conditions. Always check which reference conditions define “standard.”

Can I substitute Kv for Cv?
Not directly. They use different unit conventions. A rough conversion is Cv ≈ 1.156 Kv, but verify the relevant standard and manufacturer data before sizing.

Safety and Scope

Gas-system design and valve selection should be reviewed against applicable engineering standards, pressure ratings, materials, and the gas’s hazards. This calculator is for study and preliminary arithmetic, not a substitute for a qualified design review or approved operating procedure.

Related

Formula used
in cv | Valve flow coefficient Cv | US gpm / sqrt(psi) | 1 | 0
in p1 | Upstream absolute pressure | psia | 100 | 0.001
in p2 | Downstream absolute pressure | psia | 90 | 0
in t | Gas temperature | °F | 60 | -459.67
in sg | Gas specific gravity relative to air | - | 0.6 | 0.001
out q | Gas flow | scfh | 136.3 * cv * p1 * sqrt((p1 - p2) / (sg * (t + 459.67))) | 2
out x | Pressure-drop ratio | - | (p1 - p2) / p1 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →