molecalculator

Moles & Molar Mass

First-Order Kinetics Graph: Shape and Interpretation

Calculator No. 01-6542 · Updated · Formula and assumptions shown below

First-order rate constant k 0.0116 s^-1
Half-life
60.00 s
Result, rounded to 2 decimal places
Predicted concentration at prediction time
0.0250 mol/L
Result, rounded to 4 decimal places
Initial concentration
0.1 mol/L
Set in the form below
You enter
Initial concentration (mol/L), Concentration at time t (mol/L), Elapsed time (s), Prediction time (s)
You get
First-order rate constant k (s^-1), Half-life (s), Predicted concentration at prediction time (mol/L)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A first-order kinetics graph depends on which quantities are plotted: concentration against time gives a decreasing exponential curve, while the natural logarithm of concentration against time gives a straight line. This calculator uses concentration measurements at two times to estimate the first-order rate constant, then calculates the half-life and predicted concentration at a chosen time.

Formula

For a first-order process, the integrated rate law is ln(Ct) = ln(C0) − kt, or equivalently Ct = C0e−kt. Here, C0 is the initial concentration in mol/L, Ct is concentration after elapsed time t in mol/L, k is the first-order rate constant in s−1, and t is time in seconds. The calculator rearranges the law to find k = ln(C0/Ct)/t. The half-life is t1/2 = ln(2)/k, and concentration at a prediction time tp is Cp = C0e−ktp. The logarithm is the natural logarithm, and concentration units must match.

Worked Example

Using the defaults, C0 = 0.100 mol/L, Ct = 0.0500 mol/L, and t = 60 s:

  • Rate constant: k = ln(0.100 / 0.0500) / 60 = ln(2) / 60 = 0.011552 s−1, displayed as 0.0116 s−1.
  • Half-life: t1/2 = 0.693147 / 0.011552 = 60.000 s, displayed as 60 s.
  • At tp = 120 s: Cp = 0.100 × exp(−0.011552 × 120) = 0.025000 mol/L, displayed as 0.0250 mol/L.

Assumptions

  • The process follows a single first-order rate law over the time interval considered.
  • Both concentration values are positive, measured on the same basis, and correspond to the same reacting species.
  • Time is entered in seconds, so k and half-life are reported in reciprocal seconds and seconds.
  • The prediction assumes the same rate constant remains applicable through the prediction time; changing temperature or conditions can change k.

What the First-Order Kinetics Graph Shows

“Graph of first-order kinetics” commonly refers to either a plot of concentration versus time or a linearized plot used to test the rate law. On a concentration–time graph, the curve starts at C0 and falls steeply at first, then becomes progressively less steep. Its slope at any instant is the rate of concentration change, −kC. Because the remaining concentration keeps shrinking, the reaction’s absolute rate also slows.

For a straight-line test, plot ln(C) on the vertical axis and time on the horizontal axis. First-order data should approximately form a line with slope −k and vertical intercept ln(C0). A graph using common logarithms instead has slope −k/2.303; do not read the natural-log slope formula directly from a log10 plot. A plot of 1/C against time is not the standard first-order linearization.

How to Use the Calculator

Enter the starting concentration, a later measured concentration, and the elapsed time between those measurements. Enter a prediction time to estimate the remaining concentration from the fitted rate constant. The calculator returns k first, followed by half-life and predicted concentration.

  • Use the same concentration units for both concentration entries. They cancel in C0/Ct, but mixing units changes the ratio and invalidates k.
  • Use the time unit specified by the input, seconds. Convert minutes by multiplying by 60 and hours by 3,600 before entering them.
  • Choose a later concentration lower than the starting concentration for a decay example. The calculation requires positive concentrations because ln(0) is undefined.
  • For data with several measurements, calculate ln(C) for each observation and fit a straight line against time. The slope uses all points and is generally more informative than estimating k from only two measurements.

This is a mathematical study and lab-planning aid, not a substitute for checking whether the first-order model fits the actual measurements. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Interpreting the Rate Constant and Half-Life

The rate constant k has units of inverse time. A larger k means faster disappearance under the stated conditions. Its numerical value depends on the time unit: a value in s−1 must be converted if reporting per minute or per hour. For example, 0.011552 s−1 is 0.69312 min−1, since one minute contains 60 seconds.

In ideal first-order decay, each half-life removes half of whatever amount remains, not half of the original amount repeatedly. After one half-life, 50% remains; after two, 25%; after three, 12.5%. Thus the half-life does not depend on the starting concentration when k is constant. This differs from many zero- or second-order cases, where the half-life depends on concentration.

Checks, Limits, and Common Misconceptions

A straight-looking ln(C)-versus-time plot supports first-order behavior, but does not prove a unique mechanism. Measurement error, background signal, changing conditions, or multiple reaction pathways can bend the plot. Compare alternative rate-law plots or fit the original concentration data when deciding whether the model is appropriate.

Two-point calculations are especially sensitive to measurement uncertainty. If the two concentrations are nearly equal, the logarithmic ratio is small and small measurement errors can strongly affect the estimated k. If a measured value is at or below a detection limit, it should not be entered as zero; use an appropriate analysis that accounts for censored or uncertain data instead.

First-order kinetics describes the observed rate dependence on concentration, not necessarily a one-step molecular event. A reaction with a complicated mechanism can show first-order behavior under particular conditions. Also, a constant k is only expected when conditions such as temperature and solution environment remain sufficiently stable.

Frequently Asked Questions

What is the graph of a first-order reaction?
Concentration versus time is an exponentially decreasing curve. A plot of ln(concentration) versus time is linear, with slope −k when time units match the reported rate constant.

How do you find k from a first-order graph?
Read the slope of a natural-log concentration versus time line and take its negative: k = −slope. Alternatively, use two concentrations with k = ln(C0/Ct)/t.

Why is the first-order graph linear after taking a logarithm?
The integrated rate law is ln(Ct) = ln(C0) − kt. It has the straight-line form y = b + mx, with y = ln(C), x = time, and slope −k.

Is half-life constant for a first-order reaction?
Yes, if the rate constant stays constant. The half-life is ln(2)/k and does not depend on the initial concentration under the first-order model.

Should I plot ln(C) or log(C)?
Either can produce a straight line, but the slope differs. For ln(C), slope = −k; for log10(C), slope = −k/2.303. State which logarithm you used before calculating k.

Related

Formula used
in c0 | Initial concentration | mol/L | 0.100 | 0
in ct | Concentration at time t | mol/L | 0.0500 | 0
in t | Elapsed time | s | 60 | 0
in tp | Prediction time | s | 120 | 0
out k | First-order rate constant k | s^-1 | ln(c0 / ct) / t | 4
out half | Half-life | s | ln(2) / k | 2
out cp | Predicted concentration at prediction time | mol/L | c0 * exp(-k * tp) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →