molecalculator

Moles & Molar Mass

Half Life Chapters: Full List & Order

Calculator No. 01-7636 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Half-Life chapters are the discrete levels that make up the game’s single-player campaign. This article lists every chapter in the original Half-Life (1998) and its expansions, plus the chapters in Half-Life 2 and its episodes, in the order you play them. You’ll also find a quick breakdown of how chapter selection works, what each chapter is known for, and answers to common questions about chapter counts and skipping.

Formula

The molarity (concentration) of a solution is the amount of solute in moles divided by the volume of the solution in liters:

c = m / (M × V)

where:

  • c = molarity (mol/L, written as M)
  • m = mass of solute (g)
  • M = molar mass of the solute (g/mol)
  • V = final solution volume (L, so mL must be divided by 1000)

This is the standard definition of molar concentration. It assumes the solute is fully dissolved and the volume is the final volume of the solution, not the volume of solvent added.

Worked Example

Using the default values from the calculator: you dissolve 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) in enough water to make 250 mL of solution.

First, convert mL to L:

250 mL = 250 / 1000 = 0.250 L

Then calculate moles of NaCl:

moles = 2.922 g / 58.44 g/mol = 0.05000 mol

Now divide by the volume:

c = 0.05000 mol / 0.250 L = 0.2000 mol/L

So the molarity is 0.2000 M (or 200.0 mM). The calculator rounds to 4 decimal places, giving 0.2000 mol/L.

Assumptions

  • The solute is pure and completely dissolves.
  • The volume used is the final volume of the solution, not the volume of solvent added.
  • Temperature is near 25 °C (molarity changes slightly with temperature because volume changes).

When to Use This Calculator

Use this whenever you need to prepare a solution of known molar concentration from a solid reagent. Typical lab tasks include:

  • Making a buffer or media with a specific molarity.
  • Diluting a stock solution (though that uses a different formula).
  • Checking the concentration of a solution you already made.

The result tells you how many moles of solute are in each liter of solution. For example, a 0.200 M NaCl solution contains 0.200 moles of NaCl per liter.

Common Mistakes

  • Using solvent volume instead of final volume: If you add 250 mL of water to 2.922 g of NaCl, the final volume will be slightly more than 250 mL. Always dissolve the solute in less water, then bring the total volume up to the mark.
  • Forgetting to convert mL to L: The formula requires liters. Dividing mL by 1000 is essential.
  • Using the wrong molar mass: For hydrated salts (e.g., CuSO₄·5H₂O), include the water of hydration in the molar mass.
  • Rounding too early: Round only at the end to avoid accumulating errors.

Limits of the Formula

Molarity is temperature-dependent because liquids expand when heated. For precise work, use a volumetric flask at a controlled temperature. Also, the formula assumes the solute does not significantly change the solution volume, which is true for most dilute solutions but not for very concentrated ones. For highly accurate work, consider molality (moles per kg of solvent) instead.

Frequently Asked Questions

How do I convert molarity to mg/mL?

Multiply molarity (mol/L) by the molar mass (g/mol) to get g/L, then divide by 1000 to get mg/mL. For example, 0.200 M NaCl × 58.44 g/mol = 11.688 g/L, which is 11.688 mg/mL.

What is the difference between molarity and molality?

Molarity is moles of solute per liter of solution (volume-based). Molality is moles of solute per kilogram of solvent (mass-based). Molality does not change with temperature, while molarity does.

Can I use this calculator for any solute?

Yes, as long as you know the molar mass of the solute. The calculator works for any solid that dissolves without reacting with the solvent.

What if I only have the density of the solution?

Density is not needed for molarity. If you have a mass-based concentration (like weight percent), you would need density to convert to molarity. That is a different calculation.

Why does the calculator show “Cannot compute”?

That happens when the inputs are impossible, for example a negative mass or volume. Check that all inputs are positive numbers.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →