Yes, there is an official Half-Life remake, but it is not a full remaster of the original game. The only officially licensed remake is Black Mesa, a fan-made total conversion that Valve approved and later allowed to be sold commercially. It rebuilds the original Half-Life (1998) in the Source engine, and it was released in full on Steam in March 2020 after more than a decade of development.
Formula
Molarity (c) is the amount of solute in moles divided by the volume of solution in liters:
c = m / (M × V)
- c – molarity (mol/L)
- m – mass of solute (g)
- M – molar mass of solute (g/mol)
- V – final solution volume (L)
Note that V is in liters, so if you measure volume in milliliters you must divide by 1000. The formula assumes the solute is fully dissolved and the final volume is used, not the volume of solvent added.
Worked Example
Using the default values from the calculator: you want to prepare 250 mL of a sodium chloride (NaCl) solution. The molar mass of NaCl is 58.44 g/mol, and you weigh out 2.922 g of NaCl.
- Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
- Calculate moles of NaCl: 2.922 g ÷ 58.44 g/mol = 0.05000 mol
- Divide moles by volume: 0.05000 mol ÷ 0.250 L = 0.2000 mol/L
The calculator shows 0.2000 mol/L (or 200.0 mM).
Assumptions
- The solute is pure and completely dissolves.
- The final volume is measured after dissolving, not the solvent volume.
- Temperature is assumed to be near 25 °C; molarity changes slightly with temperature because volume expands.
How to Use the Calculator
Enter the mass of the solute you plan to weigh, its molar mass (from the periodic table or the bottle label), and the final volume of solution you want. The calculator gives the molarity. This is useful for preparing buffers, media, or any solution where you need a specific concentration.
For example, to make 500 mL of a 0.1 M KCl solution (molar mass 74.55 g/mol), you would enter 0.1 × 74.55 × 0.5 = 3.7275 g. The calculator lets you check that math quickly.
Common Mistakes
- Using solvent volume instead of final volume. When you dissolve a solid, the final volume is usually slightly different from the solvent volume. Always dilute to the mark in a volumetric flask.
- Forgetting to convert mL to L. A common error is dividing by 100 instead of 1000.
- Rounding molar mass too early. Use at least two decimal places for molar mass to get accurate results.
- Confusing molarity with molality. Molarity is moles per liter of solution; molality is moles per kilogram of solvent.
Limitations of the Formula
The formula works for dilute solutions where the solute does not significantly change the volume. For concentrated solutions, the volume change can be large, so you should prepare the solution by dissolving the solute in less solvent and then topping up to the final volume. Also, some salts hydrate (e.g., CuSO₄·5H₂O); if you use a hydrate, include the water mass in the molar mass.
Frequently Asked Questions
What is the difference between molarity and molality? Molarity is moles of solute per liter of solution, while molality is moles per kilogram of solvent. Molarity depends on temperature because volume changes, but molality does not.
How do I prepare a solution from a concentrated stock? Use the dilution formula C₁V₁ = C₂V₂. For example, to make 1 L of 0.5 M from a 2 M stock, you need 0.5 × 1 / 2 = 0.25 L of stock, then add water to 1 L.
What if my solute is a liquid, not a solid? For liquids, you usually measure volume, not mass. Convert to moles using density and molar mass, or use a different calculator for dilution.
Why does the calculator show millimolar too? Many lab solutions are made in millimolar (mM) concentrations, especially in biology. 1 M = 1000 mM, so the second line just gives you that value for convenience.
Can I use this calculator for any chemical? Yes, as long as you know the molar mass. The formula is universal for any solute.
What is the safest way to handle strong acids or bases? Always add acid to water, not water to acid, to avoid splashing. Wear gloves and goggles, and follow your lab’s safety data sheet (SDS).
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check