molecalculator

Moles & Molar Mass

How Is Propane Gas Measured? Units & Methods

Calculator No. 01-11640 · Updated · Formula and assumptions shown below

Weight of propane 21.20 lb
Energy content
457,500 BTU
= Gallons of liquid propane × 91500
Energy content
482.50 MJ
= Gallons of liquid propane × 96.5
Gallons of liquid propane
5 gal
Set in the form below
You enter
Gallons of liquid propane (gal)
You get
Weight of propane (lb), Energy content (BTU), Energy content (MJ)
Rounding
2 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Propane gas is measured by volume (liters or gallons) when liquid, by pressure (pounds per square inch or kilopascals) inside a tank, and by energy content (BTUs or megajoules) when used for heating or cooking. For practical purposes, most people measure propane in tank weight (pounds) to know how much fuel remains, or in gallons when filling a tank. This article explains the different units, how they relate, and how to read a propane tank gauge.

Formula

Liquid propane has a density of about 4.24 pounds per gallon at 60°F (15.6°C). The energy content of propane is about 91,500 BTUs per gallon, which equals about 96.5 megajoules per gallon (since 1 BTU ≈ 1.055 kJ). The formulas used in the calculator are:

  • Weight (lb) = gallons × 4.24 lb/gal
  • BTUs = gallons × 91,500 BTU/gal
  • Megajoules = gallons × 96.5 MJ/gal

These values are for liquid propane at standard temperature; the density changes slightly with temperature, but 4.24 lb/gal is the common approximation used for tank filling and appliance sizing.

Worked Example

Using the default value of 5 gallons of liquid propane:

  1. Weight = 5 gal × 4.24 lb/gal = 21.20 lb
  2. BTUs = 5 gal × 91,500 BTU/gal = 457,500 BTU
  3. Megajoules = 5 gal × 96.5 MJ/gal = 482.5 MJ

These match the calculator outputs exactly (rounded to 2 decimals for weight and MJ, and to the nearest whole BTU).

Assumptions

  • Propane is in liquid form at 60°F (15.6°C) and its density is 4.24 lb/gal.
  • Energy content is the gross heating value (higher heating value) of commercial propane.
  • The tank is filled to the standard 80% capacity, but the calculator uses the total liquid volume, not the tank’s water capacity.

Why Propane Is Measured in Different Ways

Propane is a gas at room temperature but is stored as a liquid under moderate pressure (about 100–200 psi at 70°F). Because it changes volume with temperature and pressure, there is no single “correct” way to measure it. The three main measurement contexts are:

  • Volume of liquid – used when filling tanks (gallons or liters).
  • Weight – used to estimate remaining fuel in a tank (pounds or kilograms).
  • Energy content – used to compare propane to other fuels or to size appliances (BTUs or megajoules).

Each method serves a different purpose, and understanding the conversion between them is essential for anyone buying propane, checking a tank, or planning a barbecue.

How to Read a Propane Tank Gauge

Most residential propane tanks have a float gauge that shows the percentage of liquid remaining. This gauge measures the liquid level, not the pressure, because pressure is not a reliable indicator of how much fuel is left (the vapor pressure stays relatively constant until the tank is nearly empty). The gauge reads 0% to 80% (the maximum fill level). To convert that percentage to gallons, you need to know the tank’s water capacity (in gallons). For example, a standard 20-pound barbecue tank holds about 4.7 gallons of water; at 80% full, it holds about 3.8 gallons of propane (weighing about 16 pounds).

For a 500-gallon home tank, a gauge reading of 50% means about 250 gallons of propane remain. To estimate the weight of the remaining fuel, multiply the gallons by 4.24 lb/gal.

Common Measurement Units and Conversions

Propane is measured in several units depending on the country and application. Here are the most common ones and how they relate:

  • Gallon (US) – the standard liquid volume unit in the US. 1 US gallon = 3.785 liters.
  • Liter – the metric liquid volume unit. 1 liter = 0.264 US gallons.
  • Pound (lb) – the weight unit used for tank capacity (e.g., a 20-lb tank holds about 20 lb of propane). 1 lb = 0.4536 kg.
  • Kilogram (kg) – used in metric countries. 1 kg = 2.205 lb.
  • BTU (British Thermal Unit) – the energy needed to raise 1 pound of water by 1°F. 1 gallon of propane contains about 91,500 BTU.
  • Megajoule (MJ) – the metric energy unit. 1 MJ = 947.8 BTU.

For gas-phase propane (as used in a pipeline or from a vaporizer), volume is often measured in cubic feet (ft³) or cubic meters (m³). One cubic foot of propane gas contains about 2,516 BTU, and one cubic meter contains about 88,800 BTU (at standard conditions).

How to Estimate How Much Propane You Have Left

The most reliable method for a small tank (like a BBQ cylinder) is to weigh it. The tare weight (empty weight) is stamped on the tank’s handle or collar. For a typical 20-lb tank, the tare weight is around 17–18 lb. To find the remaining propane:

  1. Weigh the tank on a bathroom scale.
  2. Subtract the tare weight (empty weight) from the total weight.
  3. The difference is the weight of the propane remaining.

For example, if your tank weighs 30 lb and the tare weight is 18 lb, you have 12 lb of propane left. Since a full 20-lb tank holds about 4.7 gallons, you can convert: 12 lb ÷ 4.24 lb/gal ≈ 2.83 gallons.

For larger tanks with a float gauge, you can read the percentage and multiply by the tank’s water capacity (in gallons) and then by 0.80 (since the tank is never filled above 80%). For example, a 250-gallon tank at 60% has 250 × 0.60 × 0.80 = 120 gallons of propane.

Why Pressure Is Not a Good Measure

Many people mistakenly think the tank pressure tells them how much propane is left. In reality, the vapor pressure of propane depends almost entirely on the temperature, not the liquid level. At 70°F, the pressure is about 110 psi, whether the tank is full or nearly empty. Only when the tank is almost completely empty (below about 5% liquid) does the pressure begin to drop significantly. Therefore, checking the pressure gauge is not a useful way to monitor fuel level.

Instead, use a float gauge (for large tanks) or weight (for small tanks). Some smart tank monitors use ultrasonic sensors to measure the liquid level electronically, which is another accurate method.

Frequently Asked Questions

How many gallons are in a 20 lb propane tank?

A 20 lb propane tank (the standard BBQ cylinder) holds about 4.7 gallons of liquid propane when full. This is because the tank’s water capacity is about 4.7 gallons, and it is filled to 80% capacity, which gives 4.7 × 0.80 = 3.76 gallons. However, the “20 lb” refers to the weight of the propane, not the volume. Since propane weighs 4.24 lb per gallon, 20 lb ÷ 4.24 ≈ 4.7 gallons.

How do I know how much propane is left in my tank?

For a small tank, weigh it and subtract the tare weight (stamped on the tank). For a large tank, read the float gauge (percentage) and multiply by the tank’s water capacity and then by 0.80. For example, a 500-gallon tank at 30% has about 500 × 0.30 × 0.80 = 120 gallons.

Is propane measured in pounds or gallons?

Both are used. In the US, small tanks are rated by weight (e.g., 20 lb, 30 lb), while large tanks are rated by gallon capacity (e.g., 250, 500 gallons). When you buy propane, you pay per gallon of liquid, but the tank’s capacity is often given in pounds. The conversion is 1 gallon ≈ 4.24 lb.

Why does my propane tank feel lighter when it’s cold?

Propane expands when warm and contracts when cold. A cold tank may have slightly lower pressure, but the weight of the liquid remains the same. However, the gauge reading can change because the liquid volume changes with temperature. To get an accurate reading, it’s best to check the gauge when the tank is at a moderate temperature (around 60°F).

Can I measure propane in cubic feet?

Yes, but only for gas-phase propane, not liquid. When propane is used as a gas (e.g., in a pipeline or after vaporization), it is measured in cubic feet (ft³) or cubic meters (m³). One cubic foot of propane gas contains about 2,516 BTU, and one gallon of liquid propane produces about 36.4 cubic feet of gas at standard conditions.

Safety and Accuracy Notes

When measuring propane, always follow the safety guidelines for handling and storing the fuel. Never fill a tank beyond 80% capacity, as liquid propane expands with temperature and can cause the tank to rupture. Use only certified tanks and have them inspected regularly. The density and energy content values used here are standard approximations; for precise engineering calculations, consult the propane supplier’s specifications, as the exact values can vary slightly with the propane composition and temperature.

Related

Formula used
in gal | Gallons of liquid propane | gal | 5 | 0.1
out lb | Weight of propane | lb | gal * 4.24 | 2
out btu | Energy content | BTU | gal * 91500 | 0
out mj | Energy content | MJ | gal * 96.5 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →