molecalculator

Moles & Molar Mass

Percent CV: Formula and How to Calculate It

Calculator No. 01-4597 · Updated · Formula and assumptions shown below

Percent CV 13.18 %
Mean
12.0000 measurement units
Result, rounded to 4 decimal places
Standard deviation
1.4142 measurement units
Result, rounded to 4 decimal places
Measurements
5 values
Set in the form below

Numbers separated by commas, spaces or new lines.

You enter
Measurements, Standard deviation type
You get
Percent CV (%), Mean (measurement units), Standard deviation (measurement units)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Percent CV (coefficient of variation) shows the size of a standard deviation relative to a mean, expressed as a percentage. Enter your measurements to calculate the sample or population percent CV and see the mean and standard deviation used in the result.

Formula

Percent CV is the standard deviation divided by the arithmetic mean, multiplied by 100:

Percent CV = (standard deviation ÷ mean) × 100%

For a sample, use the sample standard deviation: s = √[Σ(xᵢ − x̄)² ÷ (n − 1)]. For a complete population, use the population standard deviation: σ = √[Σ(xᵢ − μ)² ÷ n].

  • xᵢ: an individual measurement, in the same units as the other measurements.
  • x̄ or μ: the arithmetic mean, in the measurement units.
  • s or σ: sample or population standard deviation, in the measurement units.
  • n: number of measurements; it is dimensionless.
  • Percent CV: relative variation, expressed as a percentage and therefore dimensionless.

The calculator uses sample standard deviation by default, a common choice when your measurements are a sample from a wider process or population. Choose Population only when the values entered are the entire group you intend to describe. The calculator expects numerical values on a common scale and calculates the mean and standard deviation from the list you enter.

Worked Example

Use the default measurements 10, 12, 11, 13, and 14, and select Sample.

  1. Calculate the mean: (10 + 12 + 11 + 13 + 14) ÷ 5 = 12.
  2. Find each deviation from 12: −2, 0, −1, 1, and 2. Square them: 4, 0, 1, 1, and 4. Their sum is 10.
  3. Calculate the sample standard deviation: s = √(10 ÷ (5 − 1)) = √2 ≈ 1.4142.
  4. Divide the standard deviation by the mean and multiply by 100: (1.4142 ÷ 12) × 100 ≈ 11.79%.

The calculator reports a percent CV of 11.79%, a mean of 12, and a sample standard deviation of approximately 1.4142, in the same units as the measurements. The standard deviation shown in the output is rounded to four decimal places; the CV is rounded to two.

Assumptions

  • All entered values are quantitative measurements on the same scale and use the same units.
  • Sample is the default because observations are often a subset of a larger process; select Population when the data are the full group of interest.
  • The arithmetic mean is nonzero and positive for the usual interpretation of percent CV. The formula is undefined when the mean is zero.
  • Percent CV describes spread relative to the mean; it does not assess whether the measurements are accurate or whether a process is acceptable.

What You’ll Need

  • A list of at least two measurements, recorded in consistent units.
  • A decision about whether those values are a sample or the entire population.
  • A calculator or spreadsheet if working the arithmetic by hand.

Step-by-Step

  1. Collect comparable measurements. Use values representing the same quantity under comparable conditions. For example, do not combine masses recorded in grams with masses recorded in milligrams until you convert them to one unit.
  2. Choose sample or population. Select Sample when your observations represent a subset and you want to estimate variation in a larger group. Select Population when you have every value in the group you are describing. This choice changes the standard deviation denominator: n − 1 for a sample, n for a population.
  3. Enter the values. Replace the example list with your measurements, separated by commas. Include each valid observation once. Check decimal points, signs, and any missing or mistyped values before calculating.
  4. Find the mean. Add the measurements and divide by their count. The mean provides the reference level against which the spread is compared.
  5. Find the matching standard deviation. Calculate the deviations from the mean, square them, add the squares, and divide by n − 1 for a sample or n for a population. Take the square root. Use the calculator’s standard-deviation selection to apply the appropriate version.
  6. Divide by the mean and convert to percent. Divide the standard deviation by the mean, then multiply by 100. The result is percent CV. Keep extra digits through the calculation and round only the final value to a useful number of decimal places.
  7. Interpret the result in context. A smaller percent CV means less spread relative to the mean; a larger value means more relative spread. There is no universal cutoff for “good” or “bad”—compare it with relevant requirements, similar data, or established process criteria.

Common Mistakes

  • Using the wrong standard deviation. Sample and population formulas differ. State which one you used so another person can reproduce the result.
  • Mixing units or scales. Convert all observations to the same unit before calculating. A consistent change of unit does not change CV, but mixing units can make the result meaningless.
  • Using CV when the mean is zero or near zero. Division by zero is undefined; a mean close to zero can make CV extremely large and unstable. Report the mean and standard deviation separately instead.
  • Rounding too early. Rounding the mean or standard deviation before dividing can noticeably shift the result, especially with small datasets. Retain full calculator precision until the end.
  • Assuming CV proves data quality. CV describes relative dispersion, not bias, accuracy, normality, or whether a measurement procedure is reliable.
  • Comparing unlike data. A CV comparison can be misleading when datasets differ in measurement meaning, have very different distributions, or include negative values.

Tips

  • Keep the original observations and note the sample size, units, and whether the sample or population formula was used.
  • Use CV to compare relative spread between positive-valued datasets measured in different units, provided the quantities and contexts are meaningfully comparable.
  • For a quick check, remember that CV is a ratio multiplied by 100: if the standard deviation is 0.5 and the mean is 10, CV is 5%.
  • Report the mean and standard deviation alongside CV. The percentage alone hides the underlying scale and number of observations.
  • Follow your lab method, the safety data sheet (SDS) and your supervisor when this calculation supports bench work.

Troubleshooting

The calculator will not accept my data: Check that the list contains numbers separated by commas, without labels or units typed into the values. Enter units consistently, such as all measurements in grams.

The result is undefined or unusually large: Check whether the mean is zero or very close to zero. CV is not a useful stable summary in that situation; report the mean and standard deviation separately and explain the scale of the data.

My result differs from a spreadsheet: Verify that both calculations use the same observations and the same sample or population convention. Some tools default to sample standard deviation, while others may default to population standard deviation. Also compare unrounded values rather than displayed, rounded results.

I get a negative CV: A negative mean can produce a negative result under the signed formula. The conventional CV is generally intended for positive-ratio-scale data with a positive mean; do not simply take an absolute value without explaining that choice. For data with negative values or a mean near zero, CV may not be appropriate.

Frequently Asked Questions

What does percent CV tell you?
It expresses standard deviation as a percentage of the mean, so it summarizes variation relative to the typical value.

Is percent CV the same as relative standard deviation?
Usually, yes. Relative standard deviation (RSD) is commonly calculated as standard deviation divided by mean, multiplied by 100%; conventions can vary, so name the standard-deviation method used.

Should I use sample or population standard deviation?
Use sample standard deviation for a subset used to represent a larger group. Use population standard deviation when your data include the complete group you want to describe.

Can percent CV be greater than 100%?
Yes. It means the standard deviation is greater than the positive mean. That may be valid, though it can indicate that CV is a poor summary for the data.

Can I calculate CV for negative values?
The arithmetic may be possible, but the result may be negative or misleading if the mean is negative or close to zero. CV is most interpretable for positive-valued measurements with a positive mean.

What is a good percent CV?
There is no universal good value. Acceptable variation depends on the measurement, process, study design, and applicable criteria; compare against a relevant standard rather than a generic cutoff.

Related

Formula used
list data | Measurements | 10, 12, 11, 13, 14
sel kind | Standard deviation type | Sample=1, Population=2
out cv | Percent CV | % | 100 * (sd(data) / mean(data)) | 2
out avg | Mean | measurement units | mean(data) | 4
out stdev | Standard deviation | measurement units | sd(data) * (kind - 1) + psd(data) * (2 - kind) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →