molecalculator

Moles & Molar Mass

How to Calculate Percent Solution

Calculator No. 01-11133 · Updated · Formula and assumptions shown below

Percent (w/v) 1.17 %
Mass of solute
2.922 g
Set in the form below
Final solution volume
250 mL
Set in the form below
You enter
Mass of solute (g), Final solution volume (mL)
You get
Percent (w/v) (%)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide shows you how to calculate the percent concentration of a solution, a common calculation in chemistry and biology labs. You’ll learn the two main types (weight/volume and weight/weight), the formulas, and how to apply them step by step. By the end, you’ll be able to prepare solutions with accurate concentrations.

Formula

The most common percent solution in lab work is weight/volume (w/v), defined as:

Percent (w/v) = (mass of solute in grams / final volume of solution in mL) × 100

Where:

  • Mass of solute (g) – the amount of solid dissolved.
  • Final volume (mL) – the total volume of the solution after the solute is dissolved and made up to volume.
  • Percent (w/v) – grams of solute per 100 mL of solution.

Other variants:

  • Weight/weight (w/w): (mass of solute / mass of solution) × 100 – used when both solute and solvent are weighed.
  • Volume/volume (v/v): (volume of solute / volume of solution) × 100 – used for liquids mixed with liquids.

Worked Example

Using the default values from the calculator: mass of solute = 2.922 g, final volume = 250 mL.

Step 1: Write the formula.

Percent (w/v) = (mass of solute / final volume) × 100

Step 2: Plug in the numbers.

Percent (w/v) = (2.922 g / 250 mL) × 100

Step 3: Divide first.

2.922 / 250 = 0.011688

Step 4: Multiply by 100.

0.011688 × 100 = 1.1688%

Rounded to two decimal places, the answer is 1.17% (w/v).

Assumptions

  • The solute is completely dissolved in the solvent.
  • The final volume is measured after dissolution, not the initial solvent volume (important when the solute adds significant volume).
  • For w/v, the solute is a solid and the solvent is a liquid (usually water).
  • Temperature is assumed to be room temperature unless otherwise specified; density changes with temperature can affect w/w and v/v calculations.

What You’ll Need

  • Balance (to weigh the solute) – accuracy depends on the desired precision.
  • Volumetric flask or graduated cylinder (to measure final volume).
  • Solvent (typically distilled water).
  • Calculator (or use the one above).

Step-by-Step

  1. Determine the percent type you need. Check your protocol: it should specify % (w/v), % (w/w), or % (v/v). If not specified, assume w/v for solids in liquids.
  2. Weigh the solute. Use a clean, dry container and tare the balance. Record the mass in grams.
  3. Decide the final volume. This is the total volume of the solution you want to prepare (e.g., 250 mL).
  4. Apply the formula. For w/v: percent = (mass in g / volume in mL) × 100. For w/w: percent = (mass of solute / total mass of solution) × 100. For v/v: percent = (volume of solute / total volume of solution) × 100.
  5. Calculate the required solute amount (if preparing from a desired percent). Rearrange the formula: mass (g) = (percent / 100) × volume (mL). For example, to make 500 mL of a 2% (w/v) solution, you need (2/100) × 500 = 10 g of solute.
  6. Dissolve the solute. Add the solute to a beaker with about 70–80% of the final volume of solvent. Stir until completely dissolved.
  7. Make up to the final volume. Transfer the solution to a volumetric flask and add solvent until the bottom of the meniscus reaches the mark. Mix well.
  8. Label the solution with the concentration, solute, solvent, and date.

Common Mistakes

  • Using solvent volume instead of final volume. For w/v, the volume in the denominator is the final solution volume, not the volume of solvent added. If you add 250 mL of water to 10 g of solute, the final volume may be more than 250 mL.
  • Mixing up percent types. A 10% (w/w) solution is not the same as 10% (w/v) unless the density is exactly 1 g/mL. Always check the label.
  • Forgetting to convert units. If your volume is in liters, convert to mL (1 L = 1000 mL) before using the w/v formula, or use the formula with liters and multiply by 1000.
  • Rounding too early. Keep extra digits during intermediate steps and round only the final answer.
  • Ignoring the meniscus. When making up to volume, read at eye level at the bottom of the curved surface.

Tips

  • For precise work, always use a volumetric flask, not a beaker, for the final volume.
  • If the solute is slow to dissolve, use a stir bar or gentle heating (but let it cool back to room temperature before making up to volume, because volume changes with temperature).
  • For w/w solutions, weigh the container with the solute, then add solvent until the total mass reaches the target. For example, to make 100 g of a 5% (w/w) solution, weigh 5 g solute and add solvent until the total mass is 100 g.
  • When preparing small volumes, use a balance with appropriate precision (e.g., 0.001 g for 1% solutions).
  • Always add the solute to the solvent, not the other way around, especially for concentrated acids or bases (safety first).

Troubleshooting

My solution looks cloudy or has undissolved particles. This usually means the solute hasn’t fully dissolved. Stir longer, warm slightly (if safe), or sonicate. If it still doesn’t dissolve, check the solubility limit – you may be exceeding it.

My final volume is more than expected. This can happen if the solute adds significant volume. That’s why you should make up to the final volume after dissolution, not add all the solvent at once.

My calculated percent doesn’t match the label on the bottle. Recheck your measurements and the percent type. If you used w/v but the label says w/w, the values will differ.

I get a negative or zero percent. You likely entered a zero mass or volume. Check your inputs.

I need a different concentration than the formula gives. Use the rearranged formula to find the required solute mass or volume. For example, to make 200 mL of 3% (w/v), you need (3/100) × 200 = 6 g.

Frequently Asked Questions

What does % (w/v) mean? It means grams of solute per 100 mL of solution. For example, a 5% (w/v) NaCl solution contains 5 g of NaCl in every 100 mL of final solution.

How do I convert % (w/v) to molarity? First, convert percent to grams per liter (multiply by 10). Then divide by the molar mass of the solute. For example, 5% (w/v) = 50 g/L. If the molar mass is 58.44 g/mol (NaCl), molarity = 50 / 58.44 ≈ 0.856 M.

Is percent solution the same as parts per hundred? Yes, percent is parts per hundred. But be careful: parts per million (ppm) and parts per billion (ppb) are also used for very dilute solutions.

Can I use the percent formula for any solute? Yes, as long as the solute dissolves. For gases dissolved in liquids, percent is rarely used; molarity or ppm is more common.

What is the difference between % (w/w) and % (w/v)? % (w/w) uses mass of solute divided by total mass of solution (both in grams), while % (w/v) uses mass of solute (g) divided by volume of solution (mL). For water, 1 mL ≈ 1 g, so they are close, but for other solvents they differ.

How do I prepare a 1% solution? For w/v, dissolve 1 g of solute in enough solvent to make a final volume of 100 mL. For w/w, mix 1 g solute with 99 g solvent (total 100 g).

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in v | Final solution volume | mL | 250 | 0.001
out c | Percent (w/v) | % | (m / v) * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →