molecalculator

Moles & Molar Mass

Pressure From Density: Formula and Calculator

Calculator No. 01-2063 · Updated · Formula and assumptions shown below

Gauge pressure from fluid column 19,613.30 Pa
Absolute pressure at bottom
120,938.30 Pa
= Gauge pressure from fluid column + Pressure at surface
Fluid density
1000 kg/m^3
Set in the form below
Vertical fluid height
2 m
Set in the form below
You enter
Fluid density (kg/m^3), Vertical fluid height (m), Pressure at surface (Pa)
You get
Gauge pressure from fluid column (Pa), Absolute pressure at bottom (Pa)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate the pressure caused by a fluid column when you know the fluid’s density and the column’s vertical height. Enter density and height to get gauge pressure; add the surface pressure if you need absolute pressure. This calculation assumes the fluid is at rest and its density is uniform.

Formula

For a stationary fluid of constant density, the pressure difference across a vertical depth is pressure change equals density times gravitational acceleration times vertical depth:

ΔP = ρgh

  • ΔP is the pressure increase from the fluid surface to the point below, in pascals (Pa). This is gauge pressure when the surface is exposed to the surrounding atmosphere.
  • ρ (rho) is fluid density, in kilograms per cubic metre (kg/m³).
  • g is gravitational acceleration. The calculator uses 9.80665 m/s², the conventional standard value.
  • h is vertical depth below the fluid surface, in metres (m). It is not the length of a sloping pipe or container.

To find absolute pressure at the bottom, use Pabsolute = ΔP + Psurface. Here the calculator’s surface-pressure input is in pascals and defaults to 101,325 Pa, a standard-atmosphere reference. Use the actual pressure above the fluid if it differs from that reference. One pascal equals one newton per square metre; 1 kPa = 1,000 Pa and 1 bar = 100,000 Pa.

Worked Example

Using the calculator’s default values, take water with density 1,000 kg/m³, a vertical depth of 2 m, and a surface pressure of 101,325 Pa.

  1. Write the hydrostatic formula: ΔP = ρgh.
  2. Substitute the values: ΔP = 1,000 kg/m³ × 9.80665 m/s² × 2 m.
  3. Calculate: ΔP = 19,613.30 Pa, or 19.61 kPa. Rounded to the calculator’s two decimal places, the gauge-pressure result is 19,613.30 Pa.
  4. Add the surface pressure for absolute pressure: Pabsolute = 19,613.30 Pa + 101,325 Pa = 120,938.30 Pa.

The pressure difference is the extra pressure due to the water above the point. Absolute pressure includes the pressure already acting on the water’s surface.

Assumptions

  • The fluid is at rest, and density is constant throughout the stated depth.
  • Depth is measured vertically downward from the fluid surface.
  • The calculation uses standard gravity, 9.80665 m/s².
  • The surface pressure is 101,325 Pa unless you replace the default with a relevant value.

What You’ll Need

  • The fluid’s density in kg/m³. Use a reliable value for the fluid and its temperature or conditions; density is not universal for a substance.
  • The vertical distance from the fluid surface to the point of interest, in metres.
  • The pressure at the fluid surface if you want absolute pressure. For an open container, local atmospheric pressure is appropriate; the default is a standard reference, not a live weather reading.
  • A calculator, or the calculator above. If converting units yourself, note the conversion factors before substituting values.

Step-by-Step

  1. Choose the point where you want pressure. Identify the fluid surface and the point below it. The formula gives the pressure increase between those two levels. In a tank, for example, use the vertical depth from the liquid surface to the point at the tank bottom.
  2. Find the fluid density. Enter density in kg/m³. Water is often approximated as 1,000 kg/m³ for a basic estimate, but its density varies with temperature and is slightly different from that value under ordinary conditions. For a more accurate result, use a density value appropriate to the actual liquid and conditions.
  3. Measure vertical depth. Enter the height of fluid above the point in metres. Convert centimetres to metres by dividing by 100; convert millimetres to metres by dividing by 1,000. For example, 75 cm is 0.75 m. If the liquid surface is level with the point, depth is zero and the fluid-column pressure difference is zero.
  4. Calculate gauge pressure. Multiply density by 9.80665 m/s² and by depth: ΔP = ρgh. The units reduce to kg/(m·s²), which is a pascal. The calculator reports this pressure increase in Pa; divide by 1,000 to express it in kPa.
  5. Decide whether you need absolute pressure. Gauge pressure measures pressure relative to the pressure at the surface. Absolute pressure measures from a perfect vacuum, so add surface pressure to the gauge result. For an open tank, enter the local atmospheric pressure if known. If the liquid is sealed or pressurized, use the actual pressure at its surface instead.
  6. Check whether the model fits. The simple formula works for a static fluid with approximately uniform density. It does not calculate pressure losses caused by flow, pumps, friction, or narrow passages. For gases across a large height or conditions where density changes substantially, a constant-density calculation may be inaccurate.

Common Mistakes

  • Mixing units: Combining density in g/cm³ with height in metres without conversion gives a wrong result. Convert density to kg/m³ first; 1 g/cm³ = 1,000 kg/m³.
  • Using the wrong height: Use vertical depth, not the length of a pipe that runs diagonally or curves. Pressure depends on the vertical difference in elevation.
  • Confusing gauge and absolute pressure: ρgh gives a pressure difference. It is not the total absolute pressure unless surface pressure is zero on the absolute scale, which is not the case for an ordinary open tank.
  • Assuming every liquid has the density of water: Oils, brines, and other liquids can have substantially different densities. Use a suitable value rather than a generic estimate.
  • Applying the equation to moving fluid: The hydrostatic relation does not include velocity-related effects or frictional losses in flowing systems.
  • Rounding too early: Keep useful precision in density and depth during calculation, then round the final result to a sensible number of significant figures.

Tips

  • Write every quantity with its unit before calculating. This makes conversion errors easier to spot.
  • Use the same reference point for depth and surface pressure. A pressure reading from a gauge may already be gauge pressure, so do not add atmospheric pressure to it unless you are converting to absolute pressure.
  • For layered, stationary liquids, calculate each layer’s contribution separately and add the pressure increases: ΔP = g(ρ1h1 + ρ2h2 + …). Measure each layer’s vertical thickness.
  • State the pressure unit in reports. Pa, kPa, bar, and atmospheres are different scales; include the conversion rather than giving an unexplained number.

Troubleshooting

  • The result seems far too large or small: Check whether density is in kg/m³ and depth is in metres. A depth entered as 200 instead of 2 for 200 cm makes the result 100 times too high.
  • Gauge pressure is negative: With nonnegative density and depth, this formula should not produce a negative value. Check for a negative input, a sign convention copied from another equation, or a point that is above rather than below the reference surface.
  • Your measured pressure does not match: Confirm whether the instrument reports gauge or absolute pressure, and check the measurement location. Flow, temperature-dependent density, trapped gas, and pressure losses can also explain a difference.
  • The container is sealed or under pressure: Replace the default surface pressure with the pressure acting on the fluid surface. Ensure it is in Pa and that you know whether the source value is absolute or gauge before adding it.
  • The fluid is layered or density changes with depth: Do not use one average density without checking its suitability. Sum layer-by-layer contributions, or use a model that accounts for changing density when precision matters.

Frequently Asked Questions

Can density alone determine pressure?
No. For a fluid column, you also need vertical depth and gravitational acceleration. To find absolute pressure, you also need the pressure at the fluid surface.

Does ρgh give gauge pressure or absolute pressure?
It gives the pressure increase from the surface to the point. For a surface open to the atmosphere, that increase is gauge pressure. Add the surface pressure to get absolute pressure.

What density should I use for water?
For a rough estimate, 1,000 kg/m³ is commonly used. For a precise result, use water’s density at the relevant temperature and conditions.

Does the shape of the tank affect hydrostatic pressure?
Not at a given depth in the same stationary fluid. The pressure depends on density, gravity, and vertical depth, not the container’s width or shape.

Can I use this formula for air or another gas?
Only as an approximation when density is nearly constant over the height. For a tall gas column or changing temperature and pressure, density varies and a more detailed model may be needed.

How do I convert the answer from Pa to kPa?
Divide pascals by 1,000. For example, 19,613.30 Pa is 19.6133 kPa, or 19.61 kPa when rounded to two decimal places.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in h | Vertical fluid height | m | 2 | 0
in ps | Pressure at surface | Pa | 101325 | 0
out pg | Gauge pressure from fluid column | Pa | rho * 9.80665 * h | 2
out pa | Absolute pressure at bottom | Pa | pg + ps | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →