This guide explains how to convert electrical quantities (voltage, current, impedance, power) to the per-unit (pu) system, a method used in power system analysis to simplify calculations by normalizing values to a common base. You’ll learn the formulas, a worked example, and common pitfalls to avoid. No prior experience with per-unit is needed, but a basic understanding of Ohm’s law and power formulas helps.
What You’ll Need
- A calculator (or spreadsheet)
- The actual value you want to convert (e.g., 13.8 kV, 150 A, 5 Ω)
- The base values for the system (base voltage, base power, etc.)
- Knowledge of whether you are working with single-phase or three-phase systems
Step-by-Step
- Select base values. Choose a base power (Sbase) in VA or MVA (e.g., 100 MVA) and a base voltage (Vbase) in volts or kV (e.g., 13.8 kV). These are arbitrary but should reflect the system’s rating. For three-phase systems, Vbase is the line-to-line voltage.
- Calculate derived base values. From Sbase and Vbase, compute:
- Base current: Ibase = Sbase / (√3 × Vbase) for three-phase, or Sbase / Vbase for single-phase.
- Base impedance: Zbase = (Vbase)² / Sbase for three-phase (using line-to-line voltage), or Vbase² / Sbase for single-phase.
- Convert voltage. Divide the actual voltage (in the same units as Vbase) by Vbase. Example: Vpu = Vactual / Vbase.
- Convert current. Divide the actual current by Ibase. Example: Ipu = Iactual / Ibase.
- Convert impedance. Divide the actual impedance (in ohms) by Zbase. Example: Zpu = Zactual / Zbase.
- Convert power. Divide the actual power (in VA, W, or var) by Sbase. Example: Spu = Sactual / Sbase.
- Check your units. Ensure that all actual values are in the same base units as the base values (e.g., if Vbase is in kV, the actual voltage must be in kV).
Common Mistakes
- Mixing single-phase and three-phase formulas. Using √3 in a single-phase calculation or omitting it in three-phase leads to errors.
- Using line-to-neutral voltage with line-to-line base. Always match the voltage type.
- Forgetting to convert units. If Vbase is in kV, but actual voltage is in volts, divide by 1000 first.
- Using MVA for Sbase and VA for actual power. Convert everything to the same power unit.
- Not recalculating base impedance when changing base voltage. Base impedance changes with the square of the voltage.
Tips
- Always write down the base values at the top of your calculation to avoid confusion.
- Use a consistent base power across the entire system (e.g., 100 MVA) to simplify transformer calculations.
- When converting per-unit values from one base to another, use the formula: Zpu_new = Zpu_old × (Sbase_new / Sbase_old) × (Vbase_old / Vbase_new)².
- Remember that per-unit values are dimensionless; they are ratios.
Troubleshooting
- If your per-unit value seems too large or too small, check that you used the correct base values and that your actual value is in the same units.
- If you get a negative impedance, you likely have a sign error or are using a complex impedance incorrectly; ensure you are using the magnitude.
- If you are converting a transformer’s impedance, remember that the rated voltage on each side is different; use the base voltage appropriate for that side.
- If your three-phase calculation gives a current that seems off, verify that you used line-to-line voltage and included √3 in the denominator.
Frequently Asked Questions
Why use per-unit instead of actual values?
Per-unit simplifies calculations by removing large numbers and making transformer ratios disappear. It also helps compare equipment ratings across different voltage levels.
What are typical base values?
Common choices are 100 MVA for power and the rated voltage of a system (e.g., 13.8 kV). You can choose any, but consistency is key.
How do I convert per-unit back to actual?
Multiply the per-unit value by the corresponding base value. For example, Vactual = Vpu × Vbase.
Does per-unit work for single-phase systems?
Yes, but you omit the √3 factor in base current and impedance calculations.
What if my base voltage is different from the actual voltage?
That’s fine; the per-unit value reflects the ratio. Just ensure you use the correct base for the part of the system you’re analyzing.
Can I use per-unit for power factor calculations?
Yes, power factor is a ratio and remains the same in per-unit, but you must use consistent base power for real and reactive power.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED