molecalculator

Moles & Molar Mass

Convert wt% to Molarity: Formula and Calculator

Calculator No. 01-2338 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a solute’s weight percentage (wt%) into molarity, the number of moles of solute per liter of final solution. Enter the wt%, the solute’s molar mass, and the solution density; the calculator returns mol/L and mM. Density is needed because wt% gives a mass fraction, while molarity depends on solution volume.

Formula

The formula is:

Molarity (mol/L) = (wt% / 100) × density (g/mL) × 1000 (mL/L) ÷ molar mass (g/mol)

  • wt% is the solute’s mass divided by the solution’s mass, multiplied by 100.
  • Density is the mass of the complete solution per unit volume, in g/mL.
  • 1000 mL/L converts the solution volume from milliliters to liters.
  • Molar mass is the solute’s mass per mole, in g/mol.
  • Molarity is the amount of solute, in moles, per liter of solution.

The calculator’s equivalent expression is (w / 100) × d × 1000 / mm, where w is wt%, d is density, and mm is molar mass. The units cancel to mol/L. To report millimolar, multiply mol/L by 1000 mM per mol/L.

Worked Example

Use the calculator’s default values: a 10 wt% solution, molar mass 58.44 g/mol, and density 1.071 g/mL.

  1. Choose a 100 g portion of solution as a convenient basis. At 10 wt%, it contains 10 g of solute.
  2. Convert that solute mass to moles: 10 g ÷ 58.44 g/mol = 0.1711157 mol.
  3. Use density to find the volume of the 100 g solution: 100 g ÷ 1.071 g/mL = 93.37068 mL, or 93.37068 mL ÷ 1000 = 0.09337068 L.
  4. Divide moles by solution volume: 0.1711157 mol ÷ 0.09337068 L = 1.8321 mol/L.
  5. Convert to millimolar: 1.8321 mol/L × 1000 = 1832.1 mM, displayed as 1832 mM with the calculator’s rounding.

The same result follows directly from the formula: (10 / 100) × 1.071 × 1000 / 58.44 = 1.8321 mol/L.

Assumptions

  • The wt% is mass percent: grams of solute per 100 g of total solution.
  • The density applies to the solution at the temperature and conditions relevant to the concentration.
  • The volume used is the volume of the complete solution, not the volume of solvent added.
  • The entered molar mass matches the solute’s chemical form, including hydration or salt form where applicable.
  • This is concentration arithmetic; it does not account for chemical reactions, purity corrections, or volume changes during preparation.

Step-by-Step

  1. Confirm what the percentage means. This method is for wt% or mass percent, sometimes written % w/w. For example, 10 wt% means 10 g of solute in every 100 g of solution. Do not use it unchanged for volume percent or mass-per-volume concentration.
  2. Find the molar mass. Look up or calculate the molar mass for the exact compound and form you have, in g/mol. A hydrated compound and its anhydrous form have different molar masses; so can different salts of the same active chemical species.
  3. Find the solution density. Use a reliable value for the particular concentration and temperature, in g/mL. Density varies among substances and often changes with concentration and temperature. Do not substitute the density of pure water unless it is an appropriate value for your solution.
  4. Convert wt% to a mass fraction. Divide the percentage by 100. For 10 wt%, the mass fraction is 0.10 g solute per g solution.
  5. Use density to get solute mass per liter. Multiply the mass fraction by density and by 1000 mL/L. For the example, 0.10 × 1.071 g/mL × 1000 mL/L = 107.1 g/L of solute.
  6. Convert grams per liter to moles per liter. Divide the solute mass concentration by molar mass: 107.1 g/L ÷ 58.44 g/mol = 1.8321 mol/L. The g units cancel, leaving mol/L.
  7. Check the result and report sensible precision. Confirm that the concentration is plausible for the compound and that the density and molar mass use the expected units. Report only as many significant figures as the input data justify; extra calculator digits do not improve uncertain measurements.

Common Mistakes

  • Leaving out density: wt% alone does not specify liters of solution. You need density, or another valid way to determine final solution volume.
  • Using solvent volume instead of solution volume: Molarity is based on the final volume of the solution. Adding a stated volume of solvent to solute does not generally make that same final volume.
  • Confusing percentage types: A value in % w/v (grams per 100 mL) is not wt%. Do not treat it as a mass fraction or apply this formula without the correct conversion.
  • Mixing units: The formula here expects density in g/mL and molar mass in g/mol. If density is in kg/L, convert it or use a consistently derived formula; do not enter the number as though it were g/mL without checking equivalence.
  • Using the wrong chemical form: A molar mass for an anhydrous compound will give the wrong answer if the material is a hydrate or a different salt.
  • Over-rounding during calculation: Keep several digits in intermediate steps, then round the final answer according to the quality of the inputs.

Tips

  • Use the density listed for the specific wt% and temperature whenever available. If a reference gives density in kg/L, its numerical value is the same as g/mL, because 1 kg/L = 1 g/mL.
  • A quick dimensional check helps: mass fraction × g/mL × mL/L gives g/L; dividing by g/mol gives mol/L.
  • For a mixture with multiple solutes, calculate each solute’s molarity separately using its own wt%, molar mass, and appropriate solution density. The combined mass fractions must describe the same mixture.
  • If you know the mass of a solution sample instead, the sample mass cancels from the derivation. The density is still needed to convert the sample’s mass to volume.
  • For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Troubleshooting

The answer seems far too high or low: Check whether the input percentage is 10 rather than 0.10. The calculator expects the number in percent, so enter 10 for 10 wt%. Then verify the density unit and molar mass.

You cannot find a density for your solution: Search a trusted reference or the relevant product documentation for the exact concentration and temperature. If density is unknown, wt% cannot be converted to an exact molarity from the percentage and molar mass alone. You can report the formula or calculate a range using justified density limits, clearly labeling the estimate.

Your reference gives a different answer: Compare the density, temperature, chemical form, and definition of percentage used. Also check whether the other result is in mol/L, mmol/L, or another unit.

The solution is a mixture or reacts on preparation: A single-solute calculation may not describe it. Identify which chemical species the requested molarity refers to, and account for composition or reaction using appropriate analytical data rather than assuming all weighed material remains as that solute.

Frequently Asked Questions

Can I convert wt% to molarity without density?
No, not exactly. The wt% gives a solute-to-solution mass ratio, but molarity requires solution volume. Density provides the link between mass and volume.

Is 10 wt% the same as 10 g per 100 mL?
No. Ten wt% means 10 g of solute per 100 g of solution. Ten g per 100 mL is a mass-per-volume concentration, and the two match only under particular density conditions.

Does temperature affect the conversion?
Yes. Density can change with temperature, which changes the volume and therefore the molarity. Use density measured or reported at the relevant temperature.

Can I convert molarity back to wt%?
Yes, if you know density and molar mass. Rearrange the formula: wt% = molarity (mol/L) × molar mass (g/mol) ÷ [density (g/mL) × 1000 mL/L] × 100.

What if my concentration is given in % w/v?
That means mass per volume, commonly grams per 100 mL. Convert it to g/L, then divide by molar mass in g/mol to obtain mol/L. Do not treat % w/v as wt%.

Related

Formula used
in w | Solute concentration | wt% | 10 | 0 | 100
in mm | Molar mass | g/mol | 58.44 | 0.001
in d | Solution density | g/mL | 1.071 | 0.001
out c | Molarity | mol/L | (w / 100) * d * 1000 / mm | 4
out cm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →