molecalculator

Moles & Molar Mass

Find Mass from Volume and Molarity

Calculator No. 01-4302 · Updated · Formula and assumptions shown below

Mass of solute 2.9220 g
Amount of solute
0.0500 mol
= Molarity × (Final solution volume ÷ 1000)
Concentration in millimolar
200.00 mM
= Molarity × 1000
Molar mass
58.44 g/mol
Set in the form below
You enter
Molar mass (g/mol), Final solution volume (mL), Molarity (mol/L)
You get
Mass of solute (g), Amount of solute (mol), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds the mass of a solute needed for a specified solution volume and molarity. Enter the solute’s molar mass and the final solution volume; the calculator returns mass in grams, along with the equivalent concentration in millimolar.

Formula

First find the amount of solute in moles, then convert moles to mass using its molar mass:

n = C × V
m = n × M = C × (V / 1000) × M

  • m is the required solute mass in grams (g).
  • n is the amount of solute in moles (mol).
  • C is molarity in moles per liter (mol/L).
  • V is the final solution volume in milliliters (mL). Dividing by 1000 converts milliliters to liters.
  • M is molar mass in grams per mole (g/mol).

Molarity is defined as moles of dissolved solute per liter of final solution. The conversion from moles to grams works because the molar mass gives grams per mole. The calculator uses the entered molar mass; check that it matches the chemical formula and the form of the material you intend to use.

Worked Example

Using the calculator’s default values—molar mass 58.44 g/mol, final volume 250 mL, and molarity 0.2 mol/L—calculate the mass as follows:

  1. Convert the final volume to liters: 250 mL / 1000 = 0.25 L.
  2. Calculate the amount of solute: 0.2 mol/L × 0.25 L = 0.05000 mol.
  3. Convert the amount to mass: 0.05000 mol × 58.44 g/mol = 2.922 g.
  4. Convert molarity to millimolar for the additional output: 0.2 mol/L × 1000 = 200 mM.

The calculator therefore returns a solute mass of 2.922 g, an amount of 0.0500 mol, and a concentration of 200 mM.

Assumptions

  • The volume entered is the final solution volume, not the volume of solvent added.
  • The solute is pure, and the molar mass entered applies to its actual chemical form, including any hydrate or salt form.
  • Molarity refers to the stated solution volume and conditions; the calculation does not correct for temperature-related volume changes.
  • The formula calculates the mass of solute, not the mass of solvent or total solution.

What You’ll Need

  • The desired molarity, in mol/L.
  • The intended final solution volume, in mL.
  • The solute’s molar mass, in g/mol. Find it from the chemical formula and appropriate atomic weights, or use a reliable reference for the exact compound and form.
  • A calculator, or the calculator fields above. For bench work, also consult your lab method and the relevant safety information.

Step-by-Step

  1. Identify the exact solute. Write down its full chemical formula and confirm whether it is an anhydrous compound, a hydrate, or another specified form. These can have different molar masses.
  2. Find the molar mass. Use the molar mass for that exact formula in g/mol. If calculating it from a formula, multiply each element’s atomic weight by its count in the formula and add the contributions. For example, a compound with a different hydration state needs the water molecules included.
  3. Choose the target concentration. Enter molarity in mol/L. If your target is given in millimolar, convert it to mol/L by dividing by 1000; for example, 200 mM is 0.200 mol/L.
  4. Choose the final volume. Enter the volume of the completed solution in mL. Convert other units first: 1 L = 1000 mL, so 0.5 L is 500 mL.
  5. Calculate moles. Convert the final volume to liters by dividing by 1000, then multiply by molarity: moles = molarity × volume in liters.
  6. Calculate mass. Multiply the moles by molar mass: mass in grams = moles × molar mass in g/mol. The mol units cancel, leaving grams.
  7. Check the result and prepare only according to an approved method. Check the units and significant figures, then follow your lab method, the safety data sheet (SDS), and your supervisor. Do not treat the calculated mass as a substitute for a validated procedure.

For example, if a problem gives 200 mM and 250 mL, convert to 0.200 mol/L and 0.250 L before calculating. Using a molar mass of 58.44 g/mol gives 0.200 × 0.250 × 58.44 = 2.922 g. The calculation tells you the theoretical solute mass; it does not specify a safe or suitable laboratory procedure.

Common Mistakes

  • Using milliliters as though they were liters. Molarity is in mol/L. Convert mL to L by dividing by 1000; skipping this step makes the calculated mass 1000 times too large.
  • Entering mM as mol/L. Convert millimolar to molar by dividing by 1000. For instance, 5 mM is 0.005 mol/L, not 5 mol/L.
  • Using solvent volume instead of final volume. Molarity is based on the total volume of the solution. The volume of solvent used alone is not necessarily the final volume.
  • Choosing the wrong molar mass. Hydrates and anhydrous forms differ, as can salts with different counterions. Use the formula corresponding to the material being considered.
  • Rounding too early. Keep extra digits through the calculation, then round the final answer to a sensible precision based on the input measurements.
  • Confusing mass concentration with molarity. A value in g/L is not mol/L. Convert it using the molar mass if the task requires molarity.

Tips

  • Write down units at every step. They provide a quick check: (mol/L) × L × (g/mol) reduces to g.
  • Check the scale of the result. A larger target molarity, larger final volume, or larger molar mass increases the required mass in direct proportion.
  • Keep intermediate values unrounded. Round the reported mass only after multiplying all inputs.
  • When using a balance, the practical weighing precision and material purity may limit how closely the prepared concentration matches the calculated target.
  • If the target concentration is very small, check whether the mass is practical to measure accurately. A different, validated preparation approach may be needed; follow your lab’s procedure rather than improvising.

Troubleshooting

  • The answer is 1000 times too large or too small: check whether volume was entered in mL and whether the calculator converted it to L. Also check whether the concentration is mol/L or mM.
  • The answer seems chemically implausible: verify the compound’s formula, molar mass, and hydration state. Confirm that concentration means molarity rather than mass per volume.
  • The calculator rejects an input: use nonnegative values and compatible units. A molar mass must be greater than zero; use a positive final volume and concentration.
  • The measured or prepared concentration does not match the target: check the actual final volume, weighing record, reagent identity and purity, and whether the method’s conditions match the assumptions. Ask your supervisor before making adjustments.

Frequently Asked Questions

What is the formula for finding mass from molarity and volume?
Use mass (g) = molarity (mol/L) × volume (L) × molar mass (g/mol). Convert volume to liters before multiplying.

Can I use volume in milliliters?
Yes, if you convert it to liters by dividing by 1000. The calculator does this conversion for an input in mL.

What if I know the concentration in mM?
Divide the mM value by 1000 to get mol/L. For example, 25 mM equals 0.025 mol/L.

Does volume mean the amount of solvent?
No. It means the final total volume of the solution. Molarity is defined per liter of solution.

How do I find molar mass?
Use the compound’s chemical formula and add the atomic weights of all atoms in it, accounting for subscripts and any waters of hydration. Make sure the value matches the exact form being used.

How many significant figures should I report?
Use the precision justified by the inputs and measurement method. Keep extra digits during the calculation, then round the final mass appropriately.

Related

Formula used
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
in c | Molarity | mol/L | 0.2 | 0
out m | Mass of solute | g | c * (v / 1000) * mm | 4
out n | Amount of solute | mol | c * (v / 1000) | 4
out cm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →