Use this calculator to find pH from a hydroxide-ion concentration or a pOH value. Enter one known quantity and get the corresponding pH, using the standard dilute-aqueous-solution relationship at 25 °C. If you have a measured pH-meter reading, use that as the practical check.
Formula
For hydroxide concentration, first calculate pOH, then subtract it from the ion-product constant expressed as pKw:
pOH = −log10[OH⁻]
pH = pKw − pOH = 14 − pOH at 25 °C.
Here, [OH⁻] is the hydroxide-ion concentration in mol/L. pOH and pH are dimensionless logarithmic values. The calculator’s first output uses the entered hydroxide concentration: pH = 14 + log10([OH⁻]). Its second output is pOH = −log10([OH⁻]). The alternative route is pH = 14 − pOH when pOH is known. The fixed value 14 is pKw for water at approximately 25 °C; it is not universal at every temperature.
Use a positive concentration for [OH⁻]. The input limits allow values from 0 to 1 mol/L, but zero cannot be used in a logarithm, so enter a value greater than zero. Enter a pOH between 0 and 14 for the pOH route. The calculator assumes the value supplied is a concentration suitable for the introductory dilute-solution approximation; concentrated solutions may require activities rather than concentrations.
Worked Example
The default hydroxide concentration is 0.001 mol/L, or 1.000 × 10−3 mol/L.
1. Calculate pOH.
pOH = −log10(0.001) = −(−3) = 3.
2. Calculate pH.
pH = 14 − 3 = 11.
The calculator therefore returns pH = 11 and pOH = 3. The other default input, pOH = 3, gives the same pH: 14 − 3 = 11. This agreement is a useful check on the two ways to enter the information.
Assumptions
- The calculation uses pKw = 14.00, appropriate as a common approximation for water at 25 °C.
- The solution is dilute enough that concentration can stand in for hydroxide activity.
- The input is the hydroxide concentration of the solution, not the amount of hydroxide added before dilution.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. A pH-meter reading is the real check; temperature and ionic strength can shift pH.
What You’ll Need
- A hydroxide concentration in mol/L, or a pOH value. If your concentration is in another unit, convert it to mol/L first.
- A calculator that can take a base-10 logarithm, if you are calculating by hand.
- For an experimental result, the solution temperature and a properly calibrated pH meter. The formula gives an estimate; measurement checks the actual sample.
Step-by-Step
- Identify what you know. Use the hydroxide route if the value you have is [OH⁻], such as 0.001 mol/L. Use the pOH route if a reliable pOH value is already given. Do not enter a pH value into either field.
- Check concentration units. The calculator expects mol/L, also called molarity. Convert mmol/L to mol/L by dividing by 1,000. Convert μmol/L by dividing by 1,000,000. For example, 2 mmol/L is 0.002 mol/L. Do not confuse mmol/L with mol/L.
- Enter the hydroxide concentration. Put the positive concentration in the hydroxide field. For a concentration expressed in scientific notation, enter the coefficient and power of ten correctly; for example, 2 × 10−4 mol/L means 0.0002 mol/L.
- Read pOH and pH. The calculator first finds pOH by taking the negative base-10 logarithm, then finds pH by subtracting pOH from 14. For [OH⁻] = 0.001 mol/L, pOH is 3 and pH is 11.
- Or enter pOH directly. If pOH is your known value, enter it in the pOH field and calculate pH as 14 − pOH. The two routes should agree when they refer to the same solution and use the same temperature assumption.
- Keep sensible precision. Do not report more digits than your concentration measurement supports. A displayed result with many decimal places does not make the input more precise; round only after the calculation.
- Check the result against context. At 25 °C, an ordinary aqueous solution is generally expected to have pH between 0 and 14. Values outside that range can occur in concentrated or special systems, but the simple concentration calculation may not describe them accurately.
- Verify experimentally when it matters. Measure the solution with a calibrated meter using a suitable method. Temperature and ionic strength influence readings, and the meter reading is the practical check for the sample.
Common Mistakes
- Using log instead of negative log. pOH is −log10[OH⁻]. For a concentration below 1 mol/L, the logarithm is negative, so the minus sign makes pOH positive.
- Mixing up pH and pOH. pH is not −log[OH⁻]; that expression gives pOH. Convert with pH = 14 − pOH at 25 °C.
- Entering the wrong units. A value in mmol/L is 1,000 times the corresponding mol/L value. Convert before entering it or the logarithm, and therefore the result, will be wrong.
- Entering zero or a negative concentration. A logarithm is undefined for zero or negative numbers. Hydroxide concentration must be positive.
- Assuming pH + pOH always equals 14. This is the standard approximation at 25 °C. Water’s ion product changes with temperature, so use the appropriate pKw when conditions are not near 25 °C.
- Treating a calculated estimate as a measurement. The equation does not account fully for activity effects, contamination, calibration, or temperature-dependent behavior. Do not substitute it for a meter reading when an experimental value is required.
Tips
- Write the concentration with units before calculating, then convert to mol/L. This simple habit catches many factor-of-1,000 errors.
- For powers of ten, use the exponent directly where possible: if [OH⁻] = 10−5 mol/L, pOH = 5 and pH is about 9 at 25 °C.
- Use the relation pH + pOH = pKw as a cross-check. At 25 °C, the two values should add to 14.
- Keep the temperature with your recorded result. A pH value without temperature and measurement context may not be comparable with another reading.
- For concentrated solutions, use a method based on activities or a validated equilibrium calculation rather than relying only on concentration-based pH arithmetic.
Troubleshooting
The calculator rejects my input: Check that the hydroxide value is greater than zero and no more than 1 mol/L, or that pOH is within the stated 0–14 range. If your source gives a different unit, convert it first. A zero concentration cannot be used in a logarithm.
The result is unexpectedly acidic or basic: Recheck whether the number was entered in mol/L rather than mmol/L or μmol/L, and confirm that you used hydroxide—not hydrogen-ion—concentration. Check the exponent and decimal point carefully.
The calculated pH differs from the meter: Confirm meter calibration, temperature, sample handling, and concentration units. Ionic strength and non-ideal behavior can make concentration-based calculations differ from measured pH; rely on the meter for the actual sample and investigate using your lab’s method.
The solution is not near 25 °C: Do not assume pKw is exactly 14. Use a temperature-appropriate value of pKw and calculate pH = pKw − pOH, or measure the sample with a meter at the relevant temperature.
Frequently Asked Questions
How do I find pH from OH⁻ concentration?
Calculate pOH = −log10[OH⁻] with [OH⁻] in mol/L, then calculate pH = 14 − pOH at 25 °C.
What is the direct formula for pH from hydroxide concentration?
At 25 °C, pH = 14 + log10([OH⁻]), where [OH⁻] is in mol/L. This is the same relationship rearranged.
Can I calculate pH from pOH alone?
Yes. At 25 °C, subtract pOH from 14. For example, pOH 4 gives pH 10.
What if my OH⁻ value is in mmol/L?
Divide the number by 1,000 to convert mmol/L to mol/L before using the concentration formula.
Is pH + pOH always 14?
No. Their sum is pKw, which depends on temperature. A value of 14 is the usual approximation at 25 °C.
Why does my measured pH differ from the calculated value?
Temperature, ionic strength, calibration, and non-ideal solution behavior can affect the reading. The pH-meter reading is the real check for an experimental sample.
Related
Formula used
in oh | Hydroxide concentration | mol/L | 0.001 | 0 in poh | pOH | - | 3 | 0 out ph | pH from hydroxide concentration | - | 11 | 14 out pohcalc | pOH from hydroxide concentration | - | 3 | 14
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol