molecalculator

Moles & Molar Mass

How to Find Specific Enthalpy

Calculator No. 01-8218 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide shows you how to find specific enthalpy (h) for a pure substance, typically using temperature and pressure data from steam tables or a property calculator. You’ll learn the formula, how to apply it in a step-by-step calculation, and how to avoid common unit and reference-state errors. No prior thermodynamics knowledge is required, but familiarity with basic algebra and unit conversions helps.

Formula

For a pure substance, specific enthalpy is defined as:

h = u + P·v

where:

  • h = specific enthalpy (kJ/kg)
  • u = specific internal energy (kJ/kg)
  • P = absolute pressure (kPa)
  • v = specific volume (m³/kg)

In practice, you rarely compute h from u and v directly. Instead, you look up h from property tables (e.g., saturated steam tables or superheated vapor tables) at a given temperature and pressure. For a simple incompressible substance (like liquid water), a common approximation is:

h ≈ cp·T

where cp is the specific heat at constant pressure (kJ/(kg·K)) and T is the temperature in °C (relative to a reference state where h = 0 at 0 °C). The calculator above uses this approximation with cp = 4.19 kJ/(kg·K) for liquid water.

Worked Example

Using the default values from the calculator: T = 150 °C, P = 200 kPa.

For liquid water, we approximate h ≈ cp·T.

Step 1: Identify cp for liquid water. At typical conditions, cp ≈ 4.19 kJ/(kg·K).

Step 2: Multiply by the temperature in °C (since the reference is 0 °C):

h ≈ 4.19 × 150 = 628.5 kJ/kg

The calculator rounds to two decimal places, giving 628.50 kJ/kg.

Note: This approximation works only for liquid water at moderate temperatures (0–100 °C) and ignores pressure effects. For steam or other substances, use the appropriate property tables.

Assumptions

  • The substance is liquid water with a constant specific heat of 4.19 kJ/(kg·K).
  • The reference state for enthalpy is 0 kJ/kg at 0 °C (liquid water).
  • Pressure has negligible effect on liquid enthalpy (incompressible substance).
  • No phase change occurs; the substance remains liquid.

When to Use This Method

This simplified calculation is useful for quick estimates of the enthalpy of liquid water in heating and cooling applications, such as energy balance calculations for heat exchangers or hot water systems. However, for accurate engineering work, especially at high pressures or near the saturation curve, you must use steam tables or a thermodynamic property database. For steam (vapor) or superheated conditions, the specific enthalpy depends strongly on both temperature and pressure, and the simple cp·T formula is not valid.

How to Read the Result

The result is the specific enthalpy in kJ/kg, which represents the total energy content per unit mass of the substance relative to the reference state. A higher value indicates more thermal energy per kilogram. In energy balance calculations, you multiply the specific enthalpy by the mass flow rate (kg/s) to get the energy transfer rate in kW.

Common Mistakes

  • Using °F instead of °C: The formula assumes Celsius. If you have Fahrenheit, convert first: T(°C) = (T(°F) – 32) × 5/9.
  • Forgetting to use absolute pressure: In the full formula h = u + P·v, P must be absolute pressure, not gauge pressure. Gauge pressure is relative to atmospheric, so add atmospheric pressure (≈101.325 kPa) to gauge.
  • Using the wrong reference state: Different tables may use different reference states (e.g., 0 °C, 25 °C, or triple point). Always check the reference state of your data source.
  • Applying the liquid approximation to steam: The cp·T formula is only for liquid water. For steam, enthalpy includes latent heat and varies with pressure.
  • Unit mix-ups: Ensure cp is in kJ/(kg·K) and temperature in °C. If cp is in J/(g·K), convert to kJ/(kg·K) by multiplying by 1.

Tips

  • Always note the reference state when using enthalpy values from any source. Consistency is key when comparing or combining values.
  • For water, a more accurate cp varies slightly with temperature (ranges from 4.18 to 4.22 kJ/(kg·K) between 0 and 100 °C). Using 4.19 is a good average.
  • When dealing with steam, use the saturated steam tables for wet steam and superheated steam tables for dry steam. These tables list hf (saturated liquid), hg (saturated vapor), and hfg (latent heat).
  • For mixtures of liquid and vapor (quality x), the specific enthalpy is h = hf + x·hfg.
  • If you need high accuracy, use a thermodynamic property calculator or software, but always cross-check with tables for sanity.

Troubleshooting

  • Result seems too high or low: Check the temperature unit and the reference state. If you used °F, the result will be off by a factor of 5/9. Also, ensure you are using the correct phase (liquid vs. vapor).
  • Calculator shows “Cannot compute”: This happens if you enter a negative temperature below -273.15 °C (absolute zero) or a negative pressure. Correct the input.
  • Getting different values from tables: Different tables may use different reference states (e.g., 0 °C vs. 25 °C). Convert by adding or subtracting the difference in reference enthalpy. For liquid water, the difference is roughly cp × (T_ref2 – T_ref1).
  • Pressure effect seems ignored: In the simplified formula, pressure is not used. For liquid water, this is acceptable because the enthalpy of an incompressible substance is nearly independent of pressure. For gases, you must use the full property tables.

Frequently Asked Questions

Q: What is the difference between enthalpy and specific enthalpy?
Enthalpy (H) is the total energy of a system, measured in kJ. Specific enthalpy (h) is enthalpy per unit mass, in kJ/kg. It is an intensive property, so it does not depend on the amount of substance.

Q: Why do we use specific enthalpy instead of internal energy?
Enthalpy is convenient for constant-pressure processes because the heat transfer equals the change in enthalpy (Q = ΔH) when only pressure-volume work occurs. Many engineering systems (boilers, condensers) operate at constant pressure.

Q: Can I use this calculator for steam?
No. This calculator uses a liquid-water approximation. For steam, you must use steam tables or a property calculator that accounts for phase and pressure effects.

Q: What is the reference state for enthalpy?
There is no universal reference state. Many steam tables use 0 °C for liquid water (h = 0 at 0 °C), while others use 25 °C or the triple point. Always check the table’s reference state.

Q: How do I find specific enthalpy from a steam table?
Locate the table for your pressure (or temperature). For saturated conditions, read hf and hg. For superheated steam, find the row for your temperature and read h directly. For wet steam, use quality: h = hf + x·hfg.

Q: Does pressure affect the enthalpy of liquid water?
Very little. Because liquid water is nearly incompressible, its enthalpy changes negligibly with pressure. That is why the simplified formula ignores pressure. For gases, pressure has a significant effect.

Related

Formula used
in T | Temperature | °C | 150 | -273.15
in P | Pressure | kPa | 200 | 0
out h | Specific enthalpy | kJ/kg | T * 4.19 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →