molecalculator

Moles & Molar Mass

0.1 M Sodium Hydroxide: Calculator and Preparation

Calculator No. 01-1169 · Updated · Formula and assumptions shown below

NaOH mass for 0.1 M 1.000 g
Concentration
0.100 mol/L
Result, rounded to 3 decimal places
Concentration
100.0 mM
= Concentration × 1000
Final solution volume
250 mL
Set in the form below
You enter
Final solution volume (mL)
You get
NaOH mass for 0.1 M (g), Concentration (mol/L), Concentration (mM)
Rounding
3 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use this calculator to find the mass of sodium hydroxide (NaOH) needed for a specified final volume of 0.1 mol/L (0.1 M) solution. Enter the target volume in millilitres; it returns the NaOH mass in grams and the equivalent concentration in millimolar. Preparing the solution requires caustic-resistant protective equipment, an appropriate container, and a balance.

Formula

Mass of NaOH (g) = target concentration (mol/L) × molar mass of NaOH (g/mol) × final solution volume (mL) ÷ 1000 (mL/L). The target concentration is 0.1 mol/L, and NaOH has a molar mass of 39.997 g/mol, calculated from the standard atomic weights Na = 22.990 and O = 15.999 and H = 1.008. The division by 1000 converts millilitres to litres. The calculator’s concentration outputs use the calculated mass divided by molar mass and final volume in litres; millimolar (mM) is mol/L × 1000.

This calculation assumes the NaOH is pure and that the stated volume is the final solution volume, not the amount of water initially used. If your reagent is not sufficiently pure or its assay is known to differ from 100%, the simple calculation will not give an exact concentration; use an approved laboratory method to account for that or standardize the solution.

Worked Example

For the calculator’s default final volume of 250 mL:

  1. Convert volume to litres: 250 mL ÷ 1000 mL/L = 0.25000 L.
  2. Calculate amount of NaOH: 0.1 mol/L × 0.25000 L = 0.025000 mol.
  3. Calculate mass: 0.025000 mol × 39.997 g/mol = 0.999925 g, which rounds to 1.000 g at the calculator’s three decimal places.
  4. Check the calculated concentration using the unrounded mass: 0.999925 g ÷ 39.997 g/mol ÷ 0.25000 L = 0.10000 mol/L. This displays as 0.100 mol/L, or 100.0 mM.

Assumptions

  • NaOH is treated as pure, with molar mass 39.997 g/mol.
  • The target is 0.1 mol/L and the volume entered is the final solution volume.
  • The calculation is laboratory-planning arithmetic, not a substitute for assay correction or standardization.

What You’ll Need

  • Solid sodium hydroxide, with its label and safety data sheet (SDS) available.
  • A balance suitable for weighing the calculated mass, plus a clean weighing boat or equivalent.
  • A suitable container for dissolving the solid and a volumetric flask or other calibrated vessel for setting the final volume.
  • Deionized or distilled water, a transfer tool, and a stopper or compatible cap.
  • Chemical splash goggles, a lab coat or protective apron, and alkali-resistant gloves. Have access to the required eyewash and spill-response arrangements.

NaOH is strongly caustic. Dissolving it releases heat, and splashes can cause severe eye and skin injuries. Follow your lab method, the safety data sheet (SDS) and your supervisor. Do not prepare it outside an appropriately equipped and supervised laboratory.

Step-by-Step

  1. Choose the final volume. Enter the amount of solution you actually need, in millilitres, in the calculator. Read the required mass in grams. For 250 mL, the calculated mass is 1.000 g. Do not weigh a rounded value more coarsely than your balance can measure reliably.
  2. Set up safely. Put on the protective equipment required by the SDS and local procedure. Use a stable work area and a container with enough spare capacity for mixing. Keep the solid and solution away from skin and eyes. Never use food or drink containers.
  3. Weigh the NaOH. Use a clean, dry weighing boat. Avoid raising dust and close the reagent container promptly. NaOH absorbs moisture and carbon dioxide from air, so prolonged exposure can make the mass less representative of pure NaOH. If the material is visibly wet, contaminated, or of uncertain quality, stop and ask the responsible supervisor how to proceed.
  4. Add solid to water. Place a portion of the required water in the dissolving container, then add the NaOH slowly while stirring. Add the solid to the water—not water onto a pile of solid—and avoid splashing. The solution warms as the solid dissolves. Do not seal a hot solution or handle it in a way that risks pressure or a burn.
  5. Let it cool. Mix until no visible solid remains, then allow the solution to return to the temperature specified by your laboratory method. A warm liquid occupies a different volume from a cooled one, so setting the final volume while it is hot can produce an inaccurate concentration.
  6. Bring to final volume. Transfer the cooled solution to the calibrated vessel, rinsing the dissolving container into it as directed by the method. Add water carefully until the bottom of the liquid meniscus reaches the mark at the vessel’s calibration temperature. The target volume is the total solution volume; do not add the calculated water volume to the solid.
  7. Mix and label. Close the vessel and mix thoroughly by the method your lab allows. Label it with “0.1 mol/L NaOH,” preparation date, relevant hazard information, and any other details required by local rules. Store it in a compatible, tightly closed container according to the SDS and lab procedure. Do not use it if its identity or condition is uncertain.

Common Mistakes

  • Measuring the water rather than final solution volume: dissolving the solid changes the total volume. Dissolve first, cool, then make up to the final-volume mark.
  • Pouring water onto solid NaOH: localized heating can cause splashing. Add the solid slowly to water while mixing.
  • Filling to the mark while warm: cooling changes the volume and can leave the solution too concentrated. Wait until it reaches the specified temperature.
  • Assuming old or exposed pellets are pure: NaOH absorbs moisture and carbon dioxide. The calculated mass only gives the target concentration if reagent purity is adequate.
  • Rounding too early: keep the calculator’s unrounded value for planning and round only to a mass your balance can measure. A displayed result is not proof of the actual concentration.
  • Ignoring units: 250 mL is 0.250 L, not 250 L. The factor of 1000 in the formula is essential.

Tips

  • Plan the batch size before weighing; use the calculator again if the required final volume changes.
  • Use a calibrated volumetric vessel for accurate preparation. A general beaker is not designed to set an exact final volume.
  • Keep the container closed when not in use and follow local storage and labeling rules. NaOH solutions can absorb carbon dioxide, changing their composition over time.
  • If an exact analytical concentration is needed, follow an approved standardization procedure rather than relying only on the calculated mass.

Troubleshooting

The solution is still warm: wait for it to cool before adjusting the final volume. If it was already filled to the mark while hot, do not assume the concentration is correct; consult the method or supervisor.

Some solid remains: continue gentle mixing and check that the container has enough water and capacity. Do not add more NaOH to compensate for material that appears undissolved. If contamination or a failed preparation is suspected, isolate it and follow the laboratory’s disposal procedure.

The mass was spilled or uncertain: do not estimate what remains or add an arbitrary amount. Follow the lab’s spill procedure and restart with a verified quantity if permitted.

The wrong final volume was reached: adding water after exceeding the mark makes the solution less concentrated, while a short volume makes it more concentrated. Do not correct by guesswork; ask whether the batch can be recalculated, standardized, or must be discarded under local rules.

A splash reaches skin or eyes: immediately use the eyewash or safety shower and follow the SDS and emergency procedure. Get prompt assistance; do not delay rinsing to finish the preparation.

Frequently Asked Questions

How much NaOH is needed for 1 L of 0.1 M solution?
Using pure NaOH, the calculation gives 0.1 mol × 39.997 g/mol = 3.9997 g, approximately 4.000 g. Dissolve it in water, cool, and make the total volume up to 1 L.

Is 0.1 M the same as 0.1 N?
For NaOH in an acid–base neutralization where each mole supplies one mole of hydroxide, 0.1 mol/L corresponds to 0.1 equivalents/L. Normality depends on the reaction being considered, so molarity is the clearer concentration to report.

Can I use tap water?
For accurate laboratory work, use the water quality specified by the method, commonly deionized or distilled water. Tap water contains dissolved substances that may affect an application or measurement.

Does the calculator account for reagent purity?
No. It assumes pure NaOH. If an assay or purity is stated, the preparation needs an appropriate correction and may require standardization; follow the validated method used by your lab.

Can I store the solution for later?
Storage life depends on the container, conditions, and required accuracy. Keep it tightly closed in a compatible, clearly labeled container and follow the SDS and local procedure. For quantitative work, verify or standardize it when required.

Related

Formula used
in v | Final solution volume | mL | 250 | 0
out m | NaOH mass for 0.1 M | g | 0.1 * 39.997 * (v / 1000) | 3
out c | Concentration | mol/L | m / 39.997 / (v / 1000) | 3
out cmm | Concentration | mM | c * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →