molecalculator

Moles & Molar Mass

0.1 M Sodium Hydroxide: Calculate and Prepare It

Calculator No. 01-1170 · Updated · Formula and assumptions shown below

NaOH mass 0.9999 g
Amount of NaOH
0.0250 mol
= 0.1 × (Final solution volume ÷ 1000)
Final solution volume
250 mL
Set in the form below
You enter
Final solution volume (mL)
You get
NaOH mass (g), Amount of NaOH (mol)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the mass of sodium hydroxide (NaOH) needed to prepare a 0.1 mol/L solution at a chosen final volume. Enter the target volume in millilitres; the result is a planning calculation for laboratory work, not a substitute for checking the reagent label and solution concentration.

Formula

For a target molarity, mass = concentration × molar mass × final volume. In symbols, m = C × M × (V / 1000). Here, m is the mass of NaOH in grams, C is the target concentration in mol/L (0.1 mol/L), M is the molar mass of NaOH (39.997 g/mol, calculated from Na 22.990, O 15.999, and H 1.008), and V is the final solution volume in mL. Dividing by 1000 converts millilitres to litres. The second result is the amount in moles: n = C × (V / 1000).

Worked Example

Using the default final volume of 250 mL:

  1. Convert the volume: 250 mL / 1000 = 0.25 L.
  2. Calculate the required amount: 0.1 mol/L × 0.25 L = 0.025 mol.
  3. Calculate the mass: 0.025 mol × 39.997 g/mol = 0.999925 g.
  4. Rounded to the calculator’s four decimal places, the result is 0.9999 g NaOH.

The calculator reports 0.0250 mol as the amount of NaOH. The mass is a theoretical value; the purity and moisture content of the actual reagent can affect the concentration achieved.

Assumptions

  • The target is 0.1 mol/L, and the solute is pure, anhydrous NaOH with molar mass 39.997 g/mol.
  • The entered volume is the final solution volume, not the amount of water used.
  • NaOH is treated as fully dissociated for ordinary concentration calculations; this does not account for activity effects.
  • The calculation assumes no correction for assay, absorbed water, or carbon dioxide. Follow your lab method, the safety data sheet (SDS), and your supervisor.

What You’ll Need

  • Solid sodium hydroxide with its label and safety data sheet available.
  • Distilled or deionized water, plus a suitable container and a volumetric flask or other calibrated vessel for the final volume.
  • A balance, a clean weighing vessel, and a suitable tool for transferring the solid.
  • Laboratory coat, chemical splash goggles, and compatible chemical-resistant gloves. Use a designated work area with access to an eyewash station.

Sodium hydroxide is corrosive. Dissolving it in water releases heat and can cause splashing. Wear the required protective equipment and use your institution’s approved handling and disposal procedures. Never use food or drink containers.

Step-by-Step

  1. Choose the final volume. Enter the volume you need in the calculator. For example, 250 mL requires about 0.9999 g of pure NaOH. Confirm that the vessel is suitable for caustic solutions and can be used to measure the final volume accurately.
  2. Check the reagent. Read the container label for chemical identity, assay, and any special handling directions. Sodium hydroxide absorbs moisture and carbon dioxide from air, so an old or poorly sealed reagent may not have the assumed purity. If the assay is not effectively 100%, use your validated lab method to correct the mass or standardize the resulting solution.
  3. Put on protective equipment. Wear goggles, a lab coat, and compatible gloves. Keep the work area clear, and arrange the vessel so it cannot be knocked over. If solid or solution contacts skin or eyes, use the site’s emergency rinse procedure immediately and seek the required assistance.
  4. Weigh the calculated amount. Tare a dry weighing vessel, then add the mass shown by the calculator. Minimize the time the reagent is exposed to air, and avoid touching or transferring solid with bare hands. If you spill material, follow the local spill procedure rather than wiping it up casually.
  5. Add solid to water. Put some of the required water into a suitable container first. Slowly add the NaOH to the water while gently mixing. Do not pour water onto a pile of solid NaOH: the heat released can cause sudden boiling, splatter, or burns. Avoid inhaling dust.
  6. Let the solution cool. Continue gentle mixing until the solid has dissolved, then allow the solution to return to room temperature. The dissolution is exothermic; do not make up to the final mark while the solution is still warm, because its volume changes as it cools.
  7. Make up to the final volume. Transfer the cooled solution to the calibrated vessel, rinsing the original container into it if your method allows. Add water until the total solution volume reaches the mark. Mix thoroughly. Do not add the calculated amount of water as if it were the final volume.
  8. Label and store safely. Identify the solution as sodium hydroxide, record its concentration, preparation date, and any other details required by your lab. Use a tightly closed, compatible container and follow local storage and disposal rules. Keep it clearly separated from incompatible materials.

Common Mistakes

  • Measuring solvent instead of final volume: 250 mL of water plus NaOH does not necessarily make 250 mL of solution. Dissolve first, cool, then bring the solution to the required final volume.
  • Adding water to solid: This can create intense local heating and splashes. Add the solid gradually to water instead.
  • Using a damp or exposed reagent: NaOH can take up water and carbon dioxide, making a weighed mass less reliable. Check the label and follow the required standardization method.
  • Rounding too early: Keep the calculator’s mass unrounded until weighing. The balance’s readability and the reagent’s assay determine realistic precision; extra displayed digits do not guarantee extra accuracy.
  • Assuming the solution is exactly 0.1 M: The calculation gives the theoretical concentration under its assumptions. Accurate analytical work may require standardization against an appropriate reference according to an approved method.

Tips

  • Prepare only the volume needed for the work and use clean, suitable vessels.
  • Write the unit on every recorded value. The calculator takes mL and returns grams and moles; the target concentration is fixed at 0.1 mol/L.
  • Let the solution cool to room temperature before setting the final volume.
  • For a solution that must meet a specified analytical tolerance, account for reagent assay and standardize it using the lab’s approved procedure.

Troubleshooting

The solid will not dissolve: Keep the container stable and mix gently. Allow time for cooling if the solution is hot. Do not add more solid just to speed dissolution; verify that you weighed the right material and follow the lab method.

The solution is warm when it reaches the volume mark: Stop and let it cool to room temperature before adjusting the final volume. If it was already made to volume while hot, its concentration may be off; consult your supervisor about remaking it.

You added too much water: Do not guess how much NaOH to add back. If the final volume or concentration matters, remake the solution or use a validated correction based on a reliable measurement.

Some solid spilled or the mass is uncertain: Do not assume the intended amount reached the solution. Follow your local spill procedure and remake the batch if the concentration must be known.

The result seems inconsistent: Check that you entered millilitres, not litres, and confirm the target is 0.1 mol/L. Check the NaOH identity and purity on its label; this calculator assumes pure NaOH.

Frequently Asked Questions

How much NaOH is needed for 1 L of 0.1 M solution?
For pure NaOH, the calculation gives 0.1 mol × 39.997 g/mol = 3.9997 g, or about 4.000 g before any purity correction.

Is 0.1 M the same as 0.1 N for NaOH?
For acid-base neutralization where each mole of NaOH supplies one mole of hydroxide, 0.1 M corresponds to 0.1 N. Normality depends on the reaction being considered, so state the basis when reporting it.

Can I use tap water?
For casual, non-analytical work it may be adequate, but dissolved minerals and contaminants can affect results. Use distilled or deionized water when required by the method.

Why should the solution cool before final volume adjustment?
Dissolving NaOH releases heat, and warm solution occupies a different volume than cooled solution. Setting the mark while warm can give the wrong concentration at room temperature.

Does the calculator account for NaOH purity?
No. It assumes pure, anhydrous NaOH. If the label gives an assay below 100% or the reagent has absorbed moisture, use a validated purity correction and standardize when the application requires a known concentration.

How should I store the finished solution?
Use a tightly closed, chemically compatible container, label it clearly, and follow your lab’s storage and disposal rules. NaOH is corrosive and can absorb carbon dioxide from air.

Related

Formula used
in v | Final solution volume | mL | 250 | 0 | 1000000
out m | NaOH mass | g | 0.1 * 39.997 * (v / 1000) | 4
out n | Amount of NaOH | mol | 0.1 * (v / 1000) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →