This guide explains how to prepare a percent (%) solution, a common way to express concentration in chemistry and biology. You’ll learn the three types—weight/volume (w/v), volume/volume (v/v), and weight/weight (w/w)—and get step-by-step instructions for each. Enter the values you need, and the calculator below will compute the required mass or volume of solute and solvent.
Formula
For a weight/volume (w/v) percent solution, the formula is:
% (w/v) = (mass of solute in grams / final volume of solution in mL) × 100
For volume/volume (v/v) percent, use:
% (v/v) = (volume of solute in mL / final volume of solution in mL) × 100
For weight/weight (w/w) percent, use:
% (w/w) = (mass of solute in grams / total mass of solution in grams) × 100
Each variable is defined with its unit: mass in grams (g), volume in milliliters (mL), and total mass in grams (g). The final volume is the total volume after adding solute to solvent, not the solvent volume alone.
Worked Example
Let’s make a 0.9% (w/v) saline solution (NaCl) with a final volume of 250 mL. The molar mass of NaCl is 58.44 g/mol, but for percent we only need mass and volume.
Using the formula: % (w/v) = (mass / volume) × 100. Rearranged: mass = (% × volume) / 100 = (0.9 × 250) / 100 = 2.25 g.
So you weigh 2.25 g of NaCl, dissolve it in about 200 mL of distilled water, then add water to bring the total volume to exactly 250 mL. The calculator above gives the molarity of this solution: 2.25 g / 58.44 g/mol = 0.0385 mol, divided by 0.250 L = 0.154 mol/L (0.154 M).
Assumptions
- For w/v solutions, the solute is a solid and the solvent is a liquid (usually water).
- The final volume is measured after mixing; it may differ from the sum of solute and solvent volumes due to contraction or expansion.
- For w/w solutions, the total mass is the sum of solute and solvent masses.
- Temperature and pressure are assumed to be room conditions unless specified.
When to Use Each Type
Use w/v for solid solutes dissolved in liquid (e.g., NaCl in water). Use v/v for liquid solutes mixed with liquid solvents (e.g., ethanol in water). Use w/w when both solute and solvent are weighed, often in industrial or precise formulations, because it is temperature-independent.
How to Read the Result
A 10% (w/v) solution means 10 g of solute in every 100 mL of final solution. A 5% (v/v) solution means 5 mL of solute per 100 mL total. The percent is a ratio, so it has no units.
Common Mistakes
- Using solvent volume instead of final volume: Adding 10 g to 100 mL of water gives a final volume often greater than 100 mL. Always bring to the final volume with solvent.
- Confusing w/v with w/w: For w/w, you must weigh the solvent too, not measure its volume, because density varies with temperature.
- Rounding too early: For dilute solutions, small rounding errors in mass can significantly affect concentration.
- Ignoring the density of liquids: For v/v, measure volumes precisely; for w/w, weigh both components.
Tips
- Always use a volumetric flask for accurate final volume. Add solute, dissolve in a portion of solvent, then fill to the mark.
- For w/v, dissolve the solute in about 70-80% of the final volume, mix well, then adjust to the final volume.
- For v/v, measure the solute first, then add solvent to the final volume—this accounts for volume changes on mixing.
- Use a balance with appropriate precision (e.g., 0.01 g for 1% solutions).
- Label the solution with the percent, type (w/v, v/v, w/w), date, and your initials.
Troubleshooting
If the solute does not dissolve completely, try warming the solution gently (if safe) or stirring longer. Some solutes require pH adjustment or specific solvents. If you accidentally add too much solvent, the concentration is lower than intended; you can add more solute to correct, but it’s often easier to start over. If you added too much solute, you can dilute by adding more solvent, but recalculate the new percent.
Frequently Asked Questions
What does % w/v mean?
% w/v means grams of solute per 100 mL of final solution. For example, 5% w/v NaCl = 5 g NaCl in 100 mL total solution.
How do I make a 1% solution?
For w/v, dissolve 1 g of solute in enough solvent to make 100 mL final volume. For v/v, mix 1 mL of solute with solvent to make 100 mL.
Is percent solution the same as molarity?
No. Percent is grams or mL per 100 units, while molarity is moles per liter. To convert, you need the solute’s molar mass and the solution density.
Can I use tap water instead of distilled water?
For most lab work, use distilled or deionized water to avoid impurities that could affect reactions or measurements. Tap water contains ions and minerals.
How do I make a 10% solution from a 20% solution?
This is a dilution. Use the formula C1V1 = C2V2. If you want 100 mL of 10%, you need (10% × 100 mL) / 20% = 50 mL of the 20% solution, then dilute to 100 mL with solvent.
Why is my solution volume less than expected after adding solute?
Some solutes dissolve with volume contraction (e.g., ethanol in water). Always use a volumetric flask and adjust to the final volume with solvent to get the correct concentration.
Follow your lab method, the safety data sheet (SDS) and your supervisor when preparing any solution.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- PCR Primer Tm Calculation: How to Compute It
- Molecules to Moles Conversion Steps1.0000 mol
- Mean Rate of Reaction: How to Calculate It0.0050 mol/s
- Propane Vapor Pressure Calculator178.7 kPa
- mRNA vs Mature mRNA: Key Differences4,750
- Mass Fraction to Mole Fraction Calculator0.5195 fraction