A DNA purity calculator uses absorbance readings at 260, 280, and 230 nm to calculate the A260/A280 and A260/A230 ratios. Enter readings from the same sample and blank-corrected measurement; the calculator returns both ratios for assessing possible protein or reagent carryover. Ratios are screening indicators, not proof that DNA is uncontaminated or suitable for every application.
Formula
The calculator divides the absorbance at 260 nm by the absorbance at 280 nm, and separately divides the absorbance at 260 nm by the absorbance at 230 nm:
- A260/A280 = A260 ÷ A280
- A260/A230 = A260 ÷ A230
A260, A280, and A230 are absorbance readings at the stated wavelengths, reported in absorbance units (AU). Absorbance is dimensionless, so each ratio is also dimensionless. Use nonnegative readings from the same sample, measurement path, and blanking procedure. A denominator of zero cannot be used, and readings close to zero can make a ratio unstable; do not interpret such a result as a reliable purity measurement.
Worked Example
Using the calculator’s default readings:
- A260/A280 = 0.25 ÷ 0.137 = 1.8248, which rounds to 1.825.
- A260/A230 = 0.25 ÷ 0.125 = 2.000, which rounds to 2.000.
These are example ratios only. Whether they indicate acceptable purity depends on the sample type, measurement method, and requirements of the downstream application.
Assumptions
- All three readings are blank-corrected and measured on the same sample under comparable conditions.
- The entered absorbances are valid, nonnegative measurements and denominators are above zero.
- The calculator reports ratios only; it does not correct readings, estimate DNA concentration, or identify a contaminant.
What You’ll Need
- A nucleic-acid spectrophotometer or microvolume UV-Vis instrument that can measure at 230, 260, and 280 nm.
- A clean measurement surface or cuvette, appropriate blanking solution, and a well-mixed DNA sample.
- The instrument’s absorbance readings or exported measurement results.
- Your laboratory’s DNA purification and instrument instructions. Follow your lab method, the safety data sheet (SDS), and your supervisor.
Step-by-Step
- Choose the measurement method. Use a UV absorbance instrument capable of measuring all three wavelengths. A microvolume instrument uses a short optical path; a cuvette instrument may use a longer path. Readings and concentration calculations can depend on path length, so follow the instrument’s instructions rather than comparing unadjusted results from different setups.
- Prepare the sample and blank. Mix the DNA gently and briefly spin down droplets if your method calls for it. Use the same buffer or solvent used to elute or resuspend the DNA as the blank. A mismatch between the sample solution and blank can distort absorbance, especially near 230 nm.
- Clean and blank the instrument. Clean the measurement surface or cuvette as directed. Apply the blank, run the instrument’s blanking step, and confirm that the blank is suitable. Do not use water as a substitute if the sample is in a different buffer.
- Measure the DNA sample. Load the volume required by the instrument, making sure the sample contacts the measurement surface or fills the cuvette correctly. Avoid bubbles, fingerprints, lint, and residue. Measure at 230, 260, and 280 nm, either in one scan or with the instrument’s specified method.
- Check the readings before calculating. Confirm that the instrument accepted the sample and that the readings are within its reliable range. If it reports an error, saturation, or an absorbance too low for reliable measurement, follow its guidance. Reblank or dilute only as appropriate to the method, and record any dilution factor separately.
- Enter the readings. Enter the blank-corrected A260, A280, and A230 values in the calculator. Do not enter a concentration in place of absorbance, and do not mix readings from different samples or measurement runs.
- Calculate and interpret both ratios. Compare A260/A280 and A260/A230 with guidance for your DNA type and downstream assay. For relatively pure DNA, values around 1.8 for A260/A280 and around 2.0–2.2 for A260/A230 are commonly used as rough reference points, not pass/fail rules.
- Record context and decide whether to proceed. Save the raw readings, ratios, blank solution, instrument method, and sample identity. Check DNA concentration and integrity separately if the next step depends on them. If a ratio is unexpected or the sample is valuable, repeat the measurement and consider an independent check.
Common Mistakes
- Using the wrong blank: A blank that does not match the sample buffer can add or subtract background absorbance. Blank with the same solution used for the DNA sample.
- Relying on one ratio: A260/A280 alone will not reveal every salt, solvent, or reagent that absorbs near 230 nm. Review both ratios and the raw spectrum when available.
- Trusting ratios at very low absorbance: When readings approach the instrument’s detection limit, small measurement errors can cause large ratio changes. Treat low-signal ratios cautiously.
- Assuming a good ratio proves a good sample: RNA, degraded DNA, or other substances can affect readings. Absorbance ratios do not establish DNA integrity, identity, or freedom from all inhibitors.
- Comparing unlike measurements: Instrument path length, blanking, sample buffer, and DNA type affect comparisons. Use the same method where possible.
- Rounding too early: Enter the instrument’s reported readings at their available precision, then round the final ratios for reporting.
Tips
- Use fresh, clean consumables and avoid touching optical surfaces. Small residues can matter for low-volume measurements.
- Measure replicates when sample volume allows. Large disagreement between replicates may point to poor mixing, bubbles, contamination, or a measurement problem.
- Inspect the full UV spectrum if the instrument provides one. A spectrum may reveal unusual peaks or baseline shape that a pair of ratios cannot show.
- Use a DNA-specific fluorescence assay when you need a more selective concentration estimate, especially if RNA or free nucleotides may be present. It answers a different question from absorbance-based purity ratios.
- Use the acceptance criteria for the actual downstream application. A sample acceptable for one procedure may need additional cleanup for another.
Troubleshooting
- A ratio is undefined or extremely large: The denominator may be zero or very close to zero. Check the raw reading, blank, and instrument range; repeat the measurement rather than interpreting the ratio.
- A260/A280 is below the expected range: Protein or other UV-absorbing contamination is one possibility, but blank mismatch and low signal can also cause this. Reblank correctly, repeat, and review the sample preparation method before deciding on cleanup.
- A260/A230 is low: Carryover of salts, extraction reagents, or other compounds absorbing near 230 nm may be present. Check the buffer and purification steps, then repeat the reading. If needed, use a suitable cleanup method validated for your sample and downstream use.
- Ratios change between repeats: Mix the sample, check for bubbles or residue, clean the measurement surface, and repeat with a fresh blank. Confirm that each replicate uses the same sample and settings.
- Readings are negative or implausible: A poor blank, dirty surface, or instrument setup issue may be responsible. Reclean and reblank according to the instrument procedure; do not convert a negative reading into a positive value manually.
- Ratios look acceptable but the experiment fails: Purity ratios do not detect every inhibitor or damage. Check concentration with an appropriate method and assess integrity or assay compatibility separately.
Frequently Asked Questions
What is a good A260/A280 ratio for DNA?
About 1.8 is a common reference for relatively pure DNA. It is an approximate guide, not a universal acceptance threshold.
What is a good A260/A230 ratio?
Values around 2.0–2.2 are often cited for relatively pure nucleic acid. The sample buffer and measurement method can affect the result.
Can I measure purity with only A260/A280?
You can calculate that ratio, but it gives limited information. Measuring A260/A230 as well can help flag additional carryover, though neither ratio identifies a contaminant conclusively.
Does a purity ratio tell me the DNA concentration?
No. The ratios compare absorbance readings. Concentration requires a separate calculation or instrument result and may be inaccurate if other substances absorb at 260 nm.
Can these ratios be used for RNA?
The same wavelength ratios are also used as rough RNA purity indicators, but interpretation differs by sample type. Do not treat DNA reference values as automatic RNA acceptance criteria.
Should I purify DNA again if a ratio is outside the usual range?
Not automatically. Repeat the measurement and check blanking, signal strength, and sample requirements first. Consider cleanup only when results and downstream needs justify it.
Related
Formula used
in a260 | Absorbance at 260 nm | AU | 0.25 | 0 in a280 | Absorbance at 280 nm | AU | 0.137 | 0 in a230 | Absorbance at 230 nm | AU | 0.125 | 0 out r28 | A260/A280 purity ratio | ratio | a260 / a280 | 3 out r23 | A260/A230 purity ratio | ratio | a260 / a230 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %