molecalculator

Moles & Molar Mass

Hydrostatic Pressure and Density Calculator

Calculator No. 01-2065 · Updated · Formula and assumptions shown below

Hydrostatic gauge pressure 98,066 Pa
Absolute pressure at depth
199,392 Pa
= Surface absolute pressure + Hydrostatic gauge pressure
Gauge pressure
98.067 kPa
= Hydrostatic gauge pressure ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
You enter
Fluid density (kg/m^3), Vertical depth (m), Gravitational acceleration (m/s^2), Surface absolute pressure (Pa)
You get
Hydrostatic gauge pressure (Pa), Absolute pressure at depth (Pa), Gauge pressure (kPa)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Hydrostatic pressure is the pressure exerted by a fluid at rest because of the fluid above a point. For a uniform-density fluid, it equals density multiplied by gravitational acceleration and depth: p = ρgh. Enter the fluid’s density and the vertical depth to calculate gauge pressure; the calculator also reports absolute pressure using a standard atmospheric-pressure value.

Formula

For a stationary fluid with constant density, hydrostatic gauge pressure is pg = ρgh. Here, pg is pressure above the pressure at the fluid surface, in pascals (Pa); ρ is fluid density in kilograms per cubic metre (kg/m³); g is gravitational acceleration in metres per second squared (m/s²); and h is vertical depth below the surface in metres (m). A pascal is one newton per square metre.

Absolute pressure at depth is pabs = psurface + ρgh, where psurface is the absolute pressure acting on the fluid surface, in Pa. The calculator’s default surface pressure, 101,325 Pa, represents standard atmospheric pressure. It is a reference value, not a universal local measurement. The kPa output converts pascals to kilopascals using 1 kPa = 1,000 Pa.

Density must be in kg/m³ and depth in metres in this calculator. For a different gravitational acceleration, enter that value; 9.80665 m/s² is the conventional standard value used in the default example. The calculator treats the fluid as having uniform density and gravity as constant over the depth.

Worked Example

Using the defaults—water density 1,000 kg/m³, depth 10 m, gravitational acceleration 9.80665 m/s², and surface absolute pressure 101,325 Pa:

  1. Gauge pressure: pg = ρgh = 1,000 kg/m³ × 9.80665 m/s² × 10 m = 98,066.5 Pa, which rounds to 98,067 Pa at zero decimal places.
  2. Absolute pressure: pabs = 101,325 Pa + 98,066.5 Pa = 199,391.5 Pa, which rounds to 199,392 Pa.
  3. Gauge pressure in kilopascals: 98,066.5 Pa / 1,000 = 98.0665 kPa, which rounds to 98.067 kPa.

Assumptions

  • The fluid is at rest and has uniform density throughout the depth.
  • Gravity is constant over the vertical distance.
  • Depth is measured vertically downward from the fluid surface, not along a sloping wall or pipe.
  • The default surface pressure is standard atmospheric pressure; change it if the surface is sealed or subject to another known absolute pressure.

Why Density Determines Pressure

Pressure at depth comes from the weight of fluid supported above each unit of area. A denser fluid has more mass in the same volume, so a column of it weighs more and creates a larger pressure increase. Greater depth also means a taller column above the point, increasing the pressure in direct proportion.

For example, at the same depth and under the same gravity, a fluid with twice the density produces twice the hydrostatic gauge pressure. This relationship is why seawater produces slightly more pressure per metre than freshwater: dissolved salts make seawater denser. Exact values depend on salinity and temperature, so use a density appropriate to the fluid and conditions when precision matters.

The equation describes the pressure difference between a point and the fluid surface. It does not say that pressure acts only downward. In a stationary fluid, pressure at a point acts in all directions; the surrounding fluid transmits that pressure to walls and objects.

Gauge Pressure and Absolute Pressure

Gauge pressure is measured relative to the pressure at the surface. If an open tank is exposed to air, its surface pressure is atmospheric, and ρgh gives the pressure increase below that surface. Absolute pressure is measured from a perfect vacuum, so atmospheric pressure must be added for an open tank.

This distinction resolves a common confusion: at the surface of an open body of water, gauge pressure is approximately zero, but absolute pressure is not zero. It is approximately the local atmospheric pressure. Likewise, a pressure gauge that reads zero at the surface usually reports gauge pressure, not an absence of all pressure.

For a submerged object, hydrostatic pressure is not by itself the net force on the object. Pressure acts on all sides; the resulting force depends on pressure differences across its surfaces and on its shape and orientation. A flat horizontal area at one depth has a uniform hydrostatic pressure in this idealized model, while a vertical surface spans different depths and therefore experiences a pressure gradient.

Using the Calculator and Checking Units

Enter density, vertical depth, gravitational acceleration, and the absolute pressure at the fluid surface. The first result is gauge pressure, followed by absolute pressure and gauge pressure in kPa. For an open water tank near ordinary atmospheric conditions, the defaults are a useful illustration, but actual water density and local air pressure may differ.

  • Convert density: if a value is given in g/cm³, multiply by 1,000 to obtain kg/m³. For instance, 1.00 g/cm³ equals 1,000 kg/m³.
  • Convert depth: if depth is given in centimetres, divide by 100 to obtain metres. A 50 cm depth is 0.50 m.
  • Use vertical depth: measure the height difference from the free surface to the point. A longer path through a sloping container does not mean greater hydrostatic depth.
  • Choose the right surface pressure: use absolute pressure in Pa. For a pressurized or evacuated enclosure, standard atmospheric pressure is not the correct surface value.

Because the formula is linear in depth, doubling the depth doubles gauge pressure when density and gravity remain unchanged. Pressure values can also be expressed in other units, but conversion must be explicit: 1 kPa is 1,000 Pa, and 1 bar is 100,000 Pa. Do not mix density in g/cm³, depth in centimetres, or pressure in atmospheres directly into the SI expression without converting them.

Limits and Practical Context

The simple equation applies to a fluid at rest and with constant density. In a liquid whose density changes appreciably with depth, the more general relationship is that the pressure change is the integral of ρg over vertical depth. Gas density can vary significantly with height, so a single constant-density calculation is only an approximation over sufficiently large altitude changes.

Motion, pumps, flowing pipes, waves, and rapid changes in elevation can introduce pressure effects that this hydrostatic model does not include. It also does not calculate pressure loss from friction in a moving fluid, impact loads, or the structural strength needed to contain pressure. For engineering design or safety decisions, use the applicable fluid properties, operating conditions, and engineering standards rather than treating this estimate as a complete design calculation.

In an ordinary laboratory or educational setting, the equation is useful for estimating how pressure changes with depth in a liquid column, comparing fluids, and checking whether a pressure value is physically plausible. It is a model, not a substitute for a measured pressure when the actual system’s conditions matter.

Frequently Asked Questions

How does density affect hydrostatic pressure?
At the same depth and gravitational acceleration, pressure increase is directly proportional to density. A denser fluid produces greater hydrostatic gauge pressure.

What is the hydrostatic pressure at 10 metres of water?
Using density 1,000 kg/m³ and standard gravity 9.80665 m/s², the gauge pressure is 98,066.5 Pa, or about 98.067 kPa. Absolute pressure is higher because surface pressure must be added.

Is hydrostatic pressure the same as absolute pressure?
Not necessarily. The value ρgh is the pressure increase relative to the fluid surface. Absolute pressure equals that increase plus the absolute pressure at the surface.

Does container shape change pressure at a given depth?
No, not for a stationary fluid with the same density and surface pressure. Hydrostatic pressure at a point depends on vertical depth, density, and gravity, not on the container’s overall shape.

Why is water pressure sometimes given in metres?
A pressure head expresses pressure as the height of a specified fluid column that would create it. The conversion depends on the fluid’s density and gravity, so a stated head is not a pressure unit independent of those assumptions.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0.000001
in h | Vertical depth | m | 10 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0.000001
in pa | Surface absolute pressure | Pa | 101325 | 0
out pg | Hydrostatic gauge pressure | Pa | rho * g * h | 0
out pabs | Absolute pressure at depth | Pa | pa + pg | 0
out pkpa | Gauge pressure | kPa | pg / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →