molecalculator

Moles & Molar Mass

RCF vs g in a Centrifuge: What’s the Difference?

Calculator No. 01-2240 · Updated · Formula and assumptions shown below

Relative centrifugal force (RCF) 1,118 × g
Speed for this RCF
10,000 rpm
Result, rounded to a whole number
Rotor radius
10 cm
Set in the form below
Speed
10000 rpm
Set in the form below
You enter
Rotor radius (cm), Speed (rpm)
You get
Relative centrifugal force (RCF) (× g), Speed for this RCF (rpm)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

RCF and g describe the same kind of quantity in centrifuge work: acceleration relative to Earth’s gravitational acceleration. RCF is the numerical value, expressed as a multiple of standard gravity; “g” is the unit-like shorthand for that multiple, so 1,000 × g means an RCF of 1,000.

Formula

This calculator converts between rotor speed and relative centrifugal force using the standard approximate relation:

RCF = 1.118 × 10−5 × r × rpm2

In the calculator’s expression, the factor of 10−5 is written as 1.118 × (rpm / 1,000)2, which is algebraically equivalent. Here, r is the rotational radius in centimetres, measured from the axis of rotation to the sample point, and rpm is revolutions per minute. RCF is a dimensionless multiple of standard gravitational acceleration, conventionally written × g.

The inverse relation is rpm = 1,000 × √[RCF / (1.118 × r)], with the same radius in centimetres. The first result is the RCF for the entered radius and speed; the second is the speed required to reach that RCF at that radius. The inverse result uses the calculated RCF, so it returns the original speed apart from rounding.

Worked Example

Using the defaults, the rotor radius is 10 cm and the speed is 10,000 rpm.

  1. Convert the speed to thousands of rpm: 10,000 / 1,000 = 10.
  2. Square that value: 102 = 100.
  3. Calculate the force: 1.118 × 10 × 100 = 1,118 × g.
  4. Find the speed for that RCF and radius: 1,000 × √[1,118 / (1.118 × 10)] = 1,000 × √100 = 10,000 rpm.

The calculator displays the RCF as 1,118 × g and the corresponding speed as 10,000 rpm.

Assumptions

  • The radius entered is in centimetres and is measured from the rotation axis to the relevant sample location.
  • The rotor is operating at a steady speed; the calculation does not model acceleration, braking, or vibration.
  • The conversion uses the conventional coefficient 1.118 × 10−5 for RCF calculated with radius in centimetres and speed in rpm.
  • The result is an idealized acceleration at the stated radius, not a guarantee of the force experienced everywhere in a sample.

What RCF and g Mean

RCF stands for relative centrifugal force. It compares the rotational acceleration at a particular point in the rotor with standard gravity, approximately 9.80665 m/s2. An RCF of 500 × g therefore represents an acceleration about 500 times standard gravity at the specified radius.

In lab instructions and centrifuge displays, people often say “spin at 5,000 g.” In this context, they generally mean an RCF of 5,000, not a force measured in newtons. The written notation “× g” makes the comparison with gravity explicit. It is not a different centrifuge setting from RCF.

RCF is not the same as rpm. RPM counts how many rotations the rotor makes per minute; RCF describes the resulting acceleration. A rotor’s radius matters, so identical rpm settings can produce different RCF values in different rotors.

Why Rotor Radius Matters

Rotational acceleration rises in direct proportion to radius and in proportion to the square of rotational speed. Doubling the radius doubles RCF at the same rpm. Doubling rpm, however, makes RCF four times as large. That squared relationship is why a modest speed change can substantially alter the calculated force.

For example, at 10,000 rpm, a point 10 cm from the axis experiences about 1,118 × g, while a point 5 cm from the axis experiences about 559 × g. Those are calculations for different radii in the same rotating system; they are not contradictory readings. The sample may extend across a range of radii, so its top and bottom can experience different accelerations.

Radius conventions can vary between rotor documentation and protocols. A maximum radius may be measured to the bottom of a tube or another specified point, while a minimum radius may refer to a point nearer the axis. Use the radius definition that matches the method you are following. Substituting a different point can make the result inaccurate even if the arithmetic is correct.

How to Use the Conversion

Use the calculator to translate a stated speed into an estimated RCF, or to estimate the speed needed for a target RCF at a known radius. To use it appropriately:

  • Find the relevant radius in the rotor or method documentation, and enter it in centimetres.
  • Enter the operating speed in rpm. Do not enter a target RCF in the speed field.
  • Read the first result as RCF in × g. The second result is the rpm associated with that RCF and radius.
  • Compare the target speed and force with the limits for the rotor, tubes, and centrifuge system. Follow the specified method when it gives a defined radius convention.

If you know the required RCF but not the speed, the inverse calculation is useful. It does not establish whether a particular rotor or vessel can safely operate at that speed. That must be checked against the equipment’s specified limits and applicable laboratory instructions.

Common Conversion Errors and Limits

A frequent mistake is to treat rpm and RCF as interchangeable numbers. They are not: rpm alone is insufficient to determine RCF unless the rotational radius is also known. Another common error is entering a radius in millimetres while the formula expects centimetres. Convert millimetres to centimetres by dividing by 10; for instance, 100 mm is 10 cm.

Rounding the radius or speed too early can also shift the result. Because speed is squared, an error in rpm has a stronger effect than the same percentage error in radius. The calculator rounds its displayed values to whole numbers, but that does not mean the underlying calculation is exact for a real sample. Rotor geometry, the selected radius point, speed stability, and the method’s conventions all matter.

RCF describes acceleration, not the time required for separation or the outcome of a procedure. It cannot by itself predict sedimentation, sample recovery, or whether a separation will work. Those depend on factors such as the sample, rotor design, tube position, and the specified run conditions. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

Is 1,000 g the same as an RCF of 1,000?
Yes, when “g” is being used to report centrifuge acceleration, 1,000 g means an RCF of 1,000: acceleration one thousand times standard gravity at the stated radius.

Can I convert rpm to RCF without knowing the rotor radius?
No. The conversion requires both rpm and the radius in centimetres. The same rpm can yield different RCF values in rotors with different radii.

Does the same rpm give the same RCF in every centrifuge?
No. RCF depends on both speed and radius. Different rotors, or different sample positions in a rotor, can have different RCF values at the same rpm.

What does 1,118 × g mean?
It means the calculated acceleration at the specified radius is about 1,118 times standard gravitational acceleration. It is a relative acceleration, not a force in newtons.

Which radius should I use?
Use the radius specified by the rotor documentation or the protocol. If a method identifies a particular sample point, such as the tube bottom, use that point rather than guessing.

Related

Formula used
in r | Rotor radius | cm | 10 | 0
in s | Speed | rpm | 10000 | 0
out rcf | Relative centrifugal force (RCF) | × g | 1.118 * r * (s / 1000)^2 | 0
out rpm | Speed for this RCF | rpm | 1000 * sqrt(rcf / (1.118 * r)) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →