Pressure altitude is the altitude indicated when an altimeter is set to standard pressure; density altitude is pressure altitude corrected for nonstandard temperature, and describes how dense the air behaves. The distinction matters especially in aviation: pressure altitude is a pressure-based reference, while density altitude helps explain aircraft performance in the actual air.
Formula
This calculator estimates density altitude using the common approximation: density altitude in feet equals pressure altitude in feet plus 120 times the difference between outside air temperature and standard-atmosphere temperature at that pressure altitude, with temperatures in °C.
- PA is pressure altitude in feet.
- OAT is outside air temperature in degrees Celsius.
- ISA temperature at altitude is approximated as 15 − 2 × (PA ÷ 1,000) °C, using the standard tropospheric lapse rate of about 2 °C per 1,000 feet.
- DA is estimated density altitude in feet.
The approximation is useful for illustration and planning, but it is not a full atmospheric model or a substitute for an aircraft performance chart. It also estimates the ISA temperature from pressure altitude rather than calculating density from measured pressure, temperature, and humidity.
Worked Example
Using the defaults, pressure altitude is 5,000 ft and outside air temperature is 25 °C.
ISA temperature ≈ 15 − 2 × (5,000 ÷ 1,000) = 5 °C.
Temperature difference = 25 − 5 = 20 °C.
Density altitude ≈ 5,000 + 120 × 20 = 7,400 ft.
Assumptions
- The standard-atmosphere temperature lapse rate is approximated as 2 °C per 1,000 ft.
- The calculator uses a rule-of-thumb conversion and does not account explicitly for humidity or local atmospheric structure.
- It is for general explanation and preliminary study, not operational flight planning or aircraft performance decisions.
What Pressure Altitude Means
An altimeter does not directly measure height above the ground. It senses static air pressure and converts that pressure into an altitude indication according to a calibration. Because atmospheric pressure changes with weather and location, pilots adjust the altimeter setting to match a known local pressure when they need an indicated altitude referenced to mean sea level.
Pressure altitude is the altitude shown when the altimeter’s pressure setting is 29.92 inches of mercury (inHg), or 1013.25 hectopascals (hPa). It is a standardized pressure reference, not necessarily the aircraft’s height above terrain, nor necessarily its actual geometric height above sea level. It is commonly used for performance calculations, flight levels, and standardization between aircraft.
A lower-than-standard pressure setting generally means pressure altitude is higher than the altitude indicated with the local setting; a higher-than-standard setting generally means pressure altitude is lower. The exact relationship depends on the atmospheric pressure field. Do not confuse the altimeter setting with the pressure altitude itself: the setting is a pressure value entered into the altimeter, while pressure altitude is the resulting reference altitude under the standard setting.
What Density Altitude Means
Density altitude is the altitude in the standard atmosphere at which air would have the same density as the air at the aircraft’s location. In everyday terms, it is a way of describing how “thin” the air is for performance purposes. It is not a direct measurement of where an aircraft is, and it is not simply the elevation printed on a map.
Air density is affected mainly by pressure and temperature, and also by water vapor. At a given pressure, warmer air is less dense than cooler air. Humid air is also less dense than dry air at the same temperature and pressure, because water vapor molecules have lower average molecular mass than the nitrogen and oxygen they displace. Many quick rules of thumb consider pressure altitude and temperature but omit humidity.
When the air is warmer than standard for its pressure altitude, density altitude rises above pressure altitude. When it is colder than standard, density altitude falls below pressure altitude. If temperature matches the standard atmosphere and humidity is ignored, the two values are approximately equal.
Why the Difference Matters to Aircraft
Lower air density reduces the mass of air entering a naturally aspirated engine per intake volume and reduces the amount of lift produced for a given wing area, speed, and configuration. A propeller also has less dense air to accelerate. As a result, high density altitude can mean less engine and propeller performance, a higher true airspeed for a given indicated airspeed, and longer takeoff and landing distances. The size of each effect varies with aircraft design and conditions.
Consider an airport at 5,000 ft pressure altitude on a warm day. If the temperature is 25 °C, the simple estimate above gives a density altitude near 7,400 ft. The aircraft is still physically at the airport’s actual elevation, and its pressure altitude remains 5,000 ft; the higher density altitude communicates that the air’s density is more like standard-atmosphere air found at roughly 7,400 ft.
That number alone does not establish whether a flight is safe or whether an aircraft can depart. Pilots must use the applicable aircraft flight manual or pilot operating handbook, account for runway and obstacle conditions, weight, wind, configuration, and the relevant performance charts. Follow the aircraft’s approved procedures and current aviation weather information.
How to Estimate and Interpret It
A practical workflow is to find pressure altitude from a reliable aviation source or by setting the altimeter to 29.92 inHg (1013.25 hPa), then obtain the outside air temperature at the relevant location and time. Apply an approved aircraft-specific method or performance tool. The calculator above demonstrates the common rule of thumb, not a certified operational calculation.
- Temperature above standard: density altitude is higher than pressure altitude, often noticeably so on hot days.
- Temperature below standard: density altitude is lower than pressure altitude, though cold-weather operations still have other hazards.
- Higher elevation or lower pressure: pressure altitude tends to increase, raising density altitude unless other conditions offset it.
- Humidity: usually has a smaller effect than a substantial temperature change, but can increase density altitude and may be omitted by rough calculators.
Rules of thumb should be treated as estimates. Near the limits of aircraft performance, use the manufacturer’s performance data rather than rounding a rough density-altitude number. Weather can also vary across a runway, airport, and flight path; a single reported temperature or pressure may not represent every location or moment.
Common Misconceptions and Limits
Density altitude is not true altitude. It does not tell you how high above sea level or terrain the aircraft is. True altitude is geometric altitude adjusted for atmospheric conditions; density altitude is an equivalent-density concept. They can have different values and uses.
Pressure altitude is not always field elevation. Field elevation is the airport’s surveyed elevation above mean sea level. Pressure altitude depends on atmospheric pressure, so it may be higher or lower than field elevation.
A cool day does not erase every performance concern. Density altitude may be low, but aircraft weight, runway slope and surface, wind, obstacles, engine condition, and other factors still matter. Conversely, a warm day at a low-elevation airport can create a meaningful density-altitude penalty.
The calculator’s coefficient and lapse-rate approximation are not exact across all altitudes and atmospheric conditions. It omits humidity and assumes a simplified standard atmosphere. Use official aviation calculations and aircraft documentation for decisions, and do not treat this page’s estimate as dispatch or takeoff authorization.
Frequently Asked Questions
Is density altitude the same as pressure altitude?
No. Pressure altitude is based on pressure with the altimeter set to standard pressure. Density altitude adjusts that reference for air density, especially temperature, and can also be affected by humidity.
Can density altitude be lower than pressure altitude?
Yes. If the air is colder than standard for the pressure altitude, density is greater than standard at that pressure altitude, so density altitude is lower. Humidity can modify the result.
Why does density altitude increase on a hot day?
Warm air is less dense than cool air at the same pressure. The aircraft therefore performs as though it were operating at a higher altitude in the standard atmosphere.
How do I find pressure altitude?
Use a reliable aviation weather or performance source, or set the altimeter to 29.92 inHg (1013.25 hPa) and read the indicated altitude. Follow applicable procedures and account for instrument and reporting limitations.
Does density altitude affect cars or people?
Thin air can affect engine power and breathing at high elevations, but aviation density altitude is chiefly used to compare atmospheric density with aircraft performance. It is not a substitute for medical or vehicle-specific guidance.
Related
Formula used
in pa | Pressure altitude | ft | 5000 | -1000 in oat | Outside air temperature | °C | 25 | -80 out da | Density altitude | ft | pa + 120 * (oat - (15 - 2 * pa / 1000)) | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %