molecalculator

Moles & Molar Mass

Ka from pKa: Quick Conversion Formula

Calculator No. 01-9435 · Updated · Formula and assumptions shown below

Ka (acid dissociation constant) 1.778 × 10−5 mol/L
pKb (if conjugate base, water at 25 °C)
9.25
= 14 − pKa value
pKa value
4.75
Set in the form below
You enter
pKa value
You get
Ka (acid dissociation constant) (mol/L), pKb (if conjugate base, water at 25 °C)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To convert pKa to Ka, use the formula Ka = 10−pKa. Enter your pKa value below, and the calculator returns the acid dissociation constant (Ka) in scientific notation.

Formula

The relationship between Ka and pKa is defined by the negative base-10 logarithm:

pKa = −log₁₀(Ka)

Rearranging to solve for Ka gives:

Ka = 10−pKa

Where:

  • Ka is the acid dissociation constant, with units of mol/L (M)
  • pKa is a dimensionless number (the negative log of Ka)

The calculator also shows pKb for the conjugate base, using the water ion-product constant at 25 °C: pKa + pKb = 14.

Worked Example

Using the default pKa of 4.75 (acetic acid):

  1. Start with the formula: Ka = 10−pKa
  2. Substitute pKa = 4.75: Ka = 10−4.75
  3. Calculate: 10−4.75 = 1.7783 × 10−5 mol/L
  4. Round to 4 significant figures: Ka ≈ 1.778 × 10−5 mol/L

The calculator returns 1.778 × 10−5 mol/L, matching the known Ka of acetic acid (approximately 1.8 × 10−5 mol/L).

Assumptions

  • The conversion uses the mathematical definition of pKa exactly; no experimental error is introduced.
  • The pKb calculation assumes water at 25 °C where pKw = 14. At other temperatures, pKw differs (e.g., 13.99 at 25 °C, 13.62 at 50 °C).
  • Ka values are typically reported for dilute aqueous solutions at 25 °C and 1 atm pressure.

What pKa and Ka Actually Mean

Ka is the equilibrium constant for the dissociation of a weak acid in water:

HA ⇌ H⁺ + A⁻

Ka = [H⁺][A⁻] / [HA]

Larger Ka values indicate stronger acids—they dissociate more completely. For example, hydrochloric acid has a Ka around 10⁶ (essentially complete dissociation), while acetic acid has Ka ≈ 1.8 × 10⁻⁵. The pKa scale compresses this enormous range: a strong acid might have pKa = −7, while a very weak acid like phenol has pKa ≈ 10. Each unit of pKa represents a tenfold change in Ka.

Because pKa is logarithmic, the relationship is not linear. A difference of 2 pKa units means the Ka values differ by a factor of 100. This is why biochemists and chemists usually work with pKa values directly—they are easier to compare and plot.

When to Use This Conversion

You will need to convert pKa to Ka when:

  • Calculating the pH of a weak acid solution using the ICE table method (requires Ka, not pKa)
  • Determining the percent ionization of a weak acid
  • Comparing acid strengths quantitatively—a smaller pKa means a larger Ka and a stronger acid
  • Preparing buffer solutions where you need the exact Ka to use the Henderson-Hasselbalch equation
  • Working with polyprotic acids, where each dissociation step has its own Ka (Ka1, Ka2, Ka3) and corresponding pKa values

For example, phosphoric acid has pKa1 = 2.15, pKa2 = 7.20, and pKa3 = 12.35. Converting each gives Ka1 = 7.1 × 10⁻³, Ka2 = 6.3 × 10⁻⁸, and Ka3 = 4.5 × 10⁻¹³ mol/L. The huge spread shows how much weaker each successive dissociation step is.

Common Mistakes and Misconceptions

A frequent error is forgetting the negative sign. If you calculate 104.75 instead of 10−4.75, you get 56,234 instead of 0.0000178—a difference of ten orders of magnitude. Always double-check the exponent sign.

Another mistake is confusing pKa with pH. They are related but distinct: pH measures the actual hydrogen ion concentration in a solution, while pKa is a property of the acid itself, independent of concentration. For a weak acid, pH = pKa only when the acid is half-neutralized (when [A⁻] = [HA]).

Some students assume that a larger Ka always means a more dangerous or corrosive acid. While strong acids do have large Ka values, other factors like concentration, temperature, and the specific chemical properties matter more for safety. Ka only tells you about the equilibrium position, not about reactivity or hazards.

Also note that Ka values are temperature-dependent. The conversion formula itself is exact, but the pKa you plug in was measured at a specific temperature (usually 25 °C). If your experiment runs at 37 °C, the actual Ka will differ slightly from the converted value.

How to Read the Result

The calculator outputs Ka in scientific notation with 4 decimal places. For pKa = 4.75, the result is 1.778 × 10⁻⁵ mol/L. This means that in a 1 mol/L solution of acetic acid, roughly 0.0042% of the molecules are dissociated at equilibrium (you can verify this by solving the quadratic equation for a weak acid).

The pKb output is useful when you have the conjugate base. For acetic acid (pKa = 4.75), the acetate ion has pKb = 14 − 4.75 = 9.25. This tells you that acetate is a weak base, as expected. The relationship pKa + pKb = 14 holds only for conjugate acid-base pairs in water at 25 °C.

When interpreting results, remember that Ka values span many orders of magnitude. A “small” Ka like 10⁻¹⁰ means the acid is extremely weak—it barely dissociates. A “large” Ka like 10² means the acid is quite strong, though still not fully dissociated like a strong acid.

Limits of the Formula

The conversion Ka = 10−pKa is mathematically exact, so its limits come from the pKa value itself. pKa values are typically reported to 2-3 decimal places, which translates to an uncertainty of about 5-10% in Ka. For example, if pKa = 4.75 ± 0.01, then Ka ranges from 1.74 × 10⁻⁵ to 1.82 × 10⁻⁵ mol/L.

For very strong acids (pKa < 0) or very weak ones (pKa > 14), the Ka values become extreme (10⁷ or 10⁻¹⁴) and are rarely used directly. Chemists usually describe such acids qualitatively rather than by their Ka values.

The pKb calculation assumes pure water at 25 °C. In non-aqueous solvents or at extreme temperatures, the ion-product constant of water changes, and pKa + pKb ≠ 14. For most laboratory work in aqueous solutions near room temperature, this approximation is fine.

Finally, be aware that some sources report pKa values for the same acid differently depending on ionic strength. The thermodynamic pKa (at infinite dilution) differs slightly from the practical pKa measured in a buffer with added salts. For most calculations, the difference is small enough to ignore, but for precise work, use the pKa that matches your experimental conditions.

Frequently Asked Questions

What is the difference between Ka and pKa? Ka is the actual equilibrium constant (a number like 1.8 × 10⁻⁵), while pKa is its negative logarithm (a number like 4.75). pKa is easier to compare across acids because it compresses the huge range of Ka values into a smaller scale. Lower pKa means stronger acid.

Can I convert pKa to pH directly? No. pKa is a property of the acid, while pH is a property of the solution. For a weak acid HA at concentration C, pH depends on both Ka and C: pH = ½(pKa − log C) for dilute solutions where dissociation is small. The full calculation requires solving a quadratic equation.

Why is my calculator showing a negative Ka? It shouldn’t. Since Ka = 10−pKa and 10 raised to any real power is always positive, Ka must be positive. If you see a negative result, you likely entered a pKa outside the allowed range or there is a calculation error. Check that you entered the pKa value correctly.

How do I convert Ka to pKa? Use pKa = −log₁₀(Ka). For example, if Ka = 1.8 × 10⁻⁵, then pKa = −log₁₀(1.8 × 10⁻⁵) = 4.74. This is the inverse operation of the calculator on this page.

What is a good pKa to have for a buffer? For a buffer to work effectively, the desired pH should be within ±1 unit of the acid’s pKa. The buffer capacity is highest when pH = pKa. For example, to buffer at pH 4.75, acetic acid (pKa = 4.75) is ideal. Choose an acid whose pKa is closest to your target pH.

Does the conversion work for bases too? Yes, the same mathematical relationship applies to pKb and Kb: Kb = 10−pKb. For a conjugate acid-base pair in water at 25 °C, pKa + pKb = 14, so you can convert between acid and base strength using this relationship.

Related

Formula used
in pk | pKa value | - | 4.75 | -10 | 30
out ka | Ka (acid dissociation constant) | mol/L | 10^(-pk) | 4
out pkb | pKb (if conjugate base, water at 25 °C) | - | 14 - pk | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →