molecalculator

Moles & Molar Mass

Long Trail Distance Calculator: Plan Your Hike

Calculator No. 01-8887 · Updated · Formula and assumptions shown below

Total hiking distance 312.3 miles
Main trail length
273 miles
Set in the form below
Total side trips
12 miles
Set in the form below
Loop or backtrack factor
1.1
Set in the form below
You enter
Main trail length (miles), Total side trips (miles), Loop or backtrack factor
You get
Total hiking distance (miles)
Rounding
1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates the total distance of a long trail hike based on the trail’s length and the number of side trips or detours you plan to take. Enter the main trail length and any additional distances, and you’ll get the total miles you’ll actually walk, helping you plan food, water, and time.

Formula

The total distance is calculated as:

Total Distance = Main Trail Length + Side Trips + (Main Trail Length × (Loop Factor − 1))

  • Main Trail Length (m) – the official length of the trail, in miles (or kilometers, as long as you’re consistent).
  • Side Trips (s) – any extra miles you walk to viewpoints, shelters, or water sources that aren’t on the main trail.
  • Loop Factor (l) – a multiplier to account for backtracking, wrong turns, or doing short loops off the trail. A factor of 1.0 means no extra distance; 1.1 adds 10% of the main trail length.

Worked Example

Using the default values from the calculator: a 273-mile trail (like the Long Trail in Vermont), 12 miles of side trips, and a loop factor of 1.1.

  1. Extra from loop factor: 273 × (1.1 − 1) = 273 × 0.1 = 27.3 miles
  2. Add side trips: 273 + 12 = 285 miles
  3. Add loop extra: 285 + 27.3 = 312.3 miles

So the total hiking distance is approximately 312.3 miles, matching the calculator’s output.

Assumptions

  • All distances are in the same unit (miles or kilometers).
  • The loop factor is a rough estimate; it doesn’t account for elevation gain or terrain difficulty.
  • Side trips are one-way or round-trip distances as you plan them – the calculator simply adds them.

Why Total Distance Matters

Knowing your actual walking distance is crucial for planning. The official trail length is measured along the trail’s centerline, but you’ll rarely walk exactly that. You’ll take detours to campsites, water sources, or scenic overlooks. You might get lost and backtrack. You might do a short loop to a summit. All those extra steps add up, and they affect how much food you need, how many days you’ll be out, and how your body will feel.

For example, on the 273-mile Long Trail, a thru-hiker might add 20–30 miles in side trips to peaks like Camel’s Hump or Mount Mansfield. That’s a 10% increase, which can mean an extra day of food. On a shorter trail, say 50 miles, even a few side trips can shift your resupply plans.

How to Estimate Side Trips and Loop Factor

Before you start, look at a map or guidebook for your trail. List every planned detour:

  • Summit spurs (e.g., 0.5 miles round trip to a viewpoint)
  • Water sources that are off the trail (often 0.1–0.3 miles each)
  • Shelters or campsites that require a short walk
  • Resupply points that aren’t directly on the trail

Add those up as your side trips. For the loop factor, think about the trail’s character: a well-marked, linear trail might have a factor of 1.0–1.05. A trail with many junctions, poor signage, or lots of out-and-back spurs might be 1.1–1.2. If you’re planning to do a loop that returns to the same point, factor that in explicitly as a side trip or by increasing the loop factor.

Common Mistakes

  • Mixing units – don’t enter trail length in miles but side trips in kilometers. Convert everything to one unit first.
  • Forgetting elevation gain – total distance alone doesn’t tell you how hard a trail is. A 10-mile day with 3,000 feet of climb is much harder than a flat 10-mile day. Use this calculator for distance, but also check elevation profiles.
  • Overestimating your speed – a common rule of thumb is 2–3 miles per hour on flat terrain, but that drops to 1–2 mph with heavy packs or steep climbs. Use the total distance to estimate time, but be conservative.
  • Ignoring water sources – side trips to water can add significant distance in dry areas. Plan them carefully.

Alternatives and Related Tools

This calculator gives a simple sum. For more detailed planning, you might want:

  • Elevation gain calculators – to estimate total ascent and descent.
  • Pace calculators – to convert distance and elevation into hiking time.
  • Food and water calculators – to determine how much to carry based on days and distance.
  • GPS or mapping apps – to measure actual route distance with waypoints.

Remember that this is a planning tool, not a substitute for a physical map and a compass. Trail conditions, weather, and your own fitness will affect your actual mileage.

Frequently Asked Questions

What is the Long Trail’s official length?

The Long Trail in Vermont is officially 273 miles long, running from the Massachusetts border to the Canadian border. It’s the oldest long-distance trail in the United States, completed in 1930. However, the exact length can vary slightly as trails are rerouted.

How many miles a day should I plan on a long trail?

Most thru-hikers aim for 10–20 miles per day, depending on terrain, pack weight, and experience. On the Long Trail, with its rugged terrain and many peaks, 10–15 miles per day is common. Use the total distance from this calculator and divide by your planned daily mileage to get the number of days.

Does this calculator account for elevation gain?

No, it only calculates distance. Elevation gain is a separate factor that significantly affects hiking time and energy. For a more accurate plan, look up the trail’s total elevation gain and add time for climbing (roughly an extra 30–60 minutes per 1,000 feet of ascent).

Can I use this for any trail, not just the Long Trail?

Yes, absolutely. The calculator works for any linear or loop trail. Just enter the official length and your planned side trips. The name comes from the Long Trail, but the math applies universally.

What if I get lost and add extra miles?

That’s exactly what the loop factor is for. If you think you might make navigation errors, set the factor to 1.1 or 1.2 to add a buffer. It’s better to overestimate and have extra food than to run short.

How do I measure side trips if I don’t have a map?

Many guidebooks and trail apps list distances to viewpoints, shelters, and water sources. If you’re using a GPS or phone app, you can plot waypoints and measure the distance. Otherwise, estimate based on time: a 15-minute walk at 2 mph is roughly 0.5 miles.

Related

Formula used
in m | Main trail length | miles | 273 | 0
in s | Total side trips | miles | 12 | 0
in l | Loop or backtrack factor | - | 1.1 | 1
out t | Total hiking distance | miles | m + s + (m * (l - 1)) | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →