molecalculator

Moles & Molar Mass

Loss of Pressure Calculation: Formula & Examples

Calculator No. 01-11936 · Updated · Formula and assumptions shown below

Pressure loss 45,000 Pa
Pressure loss in bar
0.450 bar
= Pressure loss ÷ 100000
Pipe internal diameter
50 mm
Set in the form below
Pipe length
100 m
Set in the form below
You enter
Pipe internal diameter (mm), Pipe length (m), Average flow velocity (m/s), Darcy friction factor, Fluid density (kg/m³)
You get
Pressure loss (Pa), Pressure loss in bar (bar)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Loss of pressure calculation determines the drop in pressure in a pipe or system due to friction, fittings, and elevation changes. You enter the flow rate, pipe dimensions, fluid properties, and system layout, and the calculator returns the pressure loss in pascals or bar. This page explains the Darcy–Weisbach equation, the friction factor, and how to apply them to real piping problems.

Formula

The Darcy–Weisbach equation is the standard method for calculating pressure loss due to friction in a straight pipe:

Δp = f × (L / D) × (ρ × v² / 2)

Where:

  • Δp = pressure loss (Pa, N/m²)
  • f = Darcy friction factor (dimensionless)
  • L = pipe length (m)
  • D = internal pipe diameter (m)
  • ρ = fluid density (kg/m³)
  • v = average flow velocity (m/s)

This equation applies to any fluid (liquid or gas) as long as the flow is steady and the pipe is full. The friction factor f accounts for the roughness of the pipe wall and the flow regime (laminar or turbulent). For laminar flow (Reynolds number < 2300), f = 64/Re. For turbulent flow, f is found from the Colebrook equation or a Moody chart.

Worked Example

Using the default values from the calculator:

  • Pipe diameter D = 50 mm = 0.050 m
  • Length L = 100 m
  • Velocity v = 1.5 m/s
  • Friction factor f = 0.02
  • Density ρ = 1000 kg/m³ (water)

Step 1: Convert diameter to meters: D = 50 / 1000 = 0.050 m

Step 2: Calculate the dynamic pressure term: ρ × v² / 2 = 1000 × (1.5)² / 2 = 1000 × 2.25 / 2 = 1125 Pa

Step 3: Calculate the length-to-diameter ratio: L / D = 100 / 0.050 = 2000

Step 4: Multiply: Δp = 0.02 × 2000 × 1125 = 45,000 Pa

So the pressure loss is 45,000 Pa, which is 0.45 bar (since 1 bar = 100,000 Pa). The calculator shows 45,000 Pa and 0.450 bar.

Assumptions

  • The pipe is straight and horizontal (no elevation change).
  • The pipe is full of fluid (no free surface).
  • The friction factor is constant along the pipe (fully developed flow).
  • The fluid is incompressible (typical for liquids; for gases, use additional corrections if the pressure drop is large).
  • Minor losses from fittings, valves, and bends are not included in this calculation.

How to Read the Result

The pressure loss value tells you how much pressure is “used up” to overcome friction as the fluid moves through the pipe. In a pump system, the pump must provide enough head to overcome this loss plus any elevation changes and the required outlet pressure. For example, if your system needs 2 bar at the outlet and the pipe loss is 0.45 bar, the pump must supply at least 2.45 bar at the inlet.

Pressure loss is directly proportional to pipe length and the square of velocity. Doubling the flow velocity increases the loss by a factor of four. Reducing the pipe diameter also increases loss dramatically because the velocity increases for the same flow rate.

Common Mistakes and How to Avoid Them

  • Unit mix-ups: Always convert diameter to meters before using the formula. A common error is using millimeters directly, which gives a result 1000 times too large.
  • Confusing friction factor: The Darcy friction factor (f) is different from the Fanning friction factor (f_F), which is one-quarter of the Darcy value. Check which one your source uses.
  • Forgetting minor losses: The Darcy–Weisbach equation only covers straight-pipe friction. Elbows, tees, valves, and entrances add extra losses. Use equivalent lengths or loss coefficients (K) to include them.
  • Using the wrong density: Water is about 1000 kg/m³, but hot water, saltwater, or other fluids have different densities. For gases, density changes with pressure and temperature.
  • Rounding too early: Keep intermediate values with several significant figures to avoid large errors in the final answer.

When to Use This Calculation

Pressure loss calculations are used in:

  • Designing water supply systems for buildings or irrigation.
  • Sizing pumps and selecting pipe diameters for industrial processes.
  • Checking that existing pipes can deliver the required flow rate.
  • Estimating energy consumption due to friction in fluid transport.
  • Designing HVAC chilled water or hot water loops.

For a complete system, you must also consider elevation changes (static head) and the pressure required at the outlet. The total head (H) in meters is Δp/(ρg) plus elevation difference plus outlet pressure head.

Limitations and Alternatives

The Darcy–Weisbach equation assumes steady, fully developed flow in a straight pipe. It does not account for:

  • Minor losses from fittings and valves.
  • Changes in pipe diameter or direction.
  • Compressibility effects in gases when the pressure drop is more than about 10% of the inlet pressure.
  • Non-Newtonian fluids (e.g., slurries, polymer solutions).

For complex systems, engineers use software that applies the same equations but adds minor losses and iterates for the friction factor. The Hazen–Williams equation is an alternative for water pipes, but it is empirical and less accurate for different fluids. For gas pipelines, the Weymouth or Panhandle equations are often used.

To get the friction factor for turbulent flow, you need the Reynolds number (Re = ρvD/μ) and the relative roughness (ε/D). The Colebrook equation is implicit, so it is usually solved numerically. For quick estimates, the Moody chart or explicit approximations like the Swamee–Jain equation are used.

Frequently Asked Questions

What is the difference between pressure loss and head loss?

Pressure loss (Δp) is the actual pressure drop in pascals or bar. Head loss (h_f) is the equivalent height of fluid column that represents that pressure drop: h_f = Δp/(ρg). For water, 1 bar of pressure loss equals about 10.2 meters of head. Pumps are often rated in head (meters) rather than pressure.

How do I include fittings like elbows and valves?

Each fitting has a loss coefficient K, and the additional pressure loss is Δp_fitting = K × (ρv²/2). You can also use the equivalent length method, where each fitting is assigned a length of straight pipe that would cause the same loss. Add these lengths to the pipe length before using the formula.

Does pipe roughness matter?

Yes. Rough pipes (e.g., cast iron, concrete) have higher friction factors than smooth pipes (e.g., plastic, copper). The friction factor depends on the relative roughness (ε/D) and Reynolds number. For laminar flow, roughness does not matter, but for turbulent flow it does. Always use the correct friction factor for your pipe material.

What is the maximum acceptable pressure loss?

There is no universal limit; it depends on the system. For water distribution, a loss of 0.5 bar per 100 m is often acceptable, but for long pipelines, designers aim for lower losses to reduce pumping energy. For gravity-fed systems, the available head determines the maximum loss. Check local codes or design guidelines for your application.

Why does the calculator show pressure loss in pascals and bar?

Pascals are the SI unit for pressure, but bar is common in engineering and industry (1 bar = 100,000 Pa). The calculator gives both so you can use the result directly in pump curves or pressure gauges without conversion.

Related

Formula used
in d | Pipe internal diameter | mm | 50 | 0.001
in l | Pipe length | m | 100 | 0
in v | Average flow velocity | m/s | 1.5 | 0
in f | Darcy friction factor | - | 0.02 | 0.0001
in rho | Fluid density | kg/m³ | 1000 | 0
out dp | Pressure loss | Pa | f * (l / (d / 1000)) * (rho * v^2 / 2) | 0
out dpbar | Pressure loss in bar | bar | dp / 100000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →