Calculate the mass of a solute from its molarity, the final solution volume, and the solute’s molar mass. Enter those three values to get the required mass in grams, plus the corresponding amount in moles; the result assumes the stated molarity is the concentration of the finished solution.
Formula
The mass is m = C × V × M, where m is solute mass in grams (g), C is molarity in moles per litre (mol/L), V is final solution volume in litres (L), and M is molar mass in grams per mole (g/mol). The units cancel to give grams: (mol/L) × L × (g/mol) = g.
The calculator accepts volume in millilitres, so it converts that value explicitly: V (L) = V (mL) / 1000. In calculator terms, m = C × (v / 1000) × M, where v is the entered volume in mL. The amount of solute is n = C × V, or n = C × (v / 1000) with the entered units. Molarity itself is concentration: C = n / V.
Worked Example
Using the calculator’s default values—0.2 mol/L, 250 mL, and 58.44 g/mol—first convert the final volume to litres:
V = 250 mL / 1000 = 0.25 L
Then calculate the number of moles:
n = 0.2 mol/L × 0.25 L = 0.05 mol
Finally, multiply by molar mass:
m = 0.05 mol × 58.44 g/mol = 2.922 g
The calculator displays the mass to three decimal places: 2.922 g. It also reports 0.0500 mol to four decimal places. These values are the theoretical amount of pure solute needed for a final solution volume of 250 mL at 0.2 mol/L.
Assumptions
- The requested volume is the final solution volume, not the volume of solvent initially measured.
- The solute is pure, and the entered molar mass applies to its chemical form and composition.
- The stated molarity describes the finished solution at the conditions relevant to its preparation and use.
- This is arithmetic for study and lab planning, not a substitute for a validated method. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
How to Use the Result
Enter molarity in mol/L, volume in mL, and molar mass in g/mol. The mass output is how many grams of solute the equation calls for; the moles output is a useful check on the calculation. If your source gives concentration in millimolar, convert it first: 1 mM = 0.001 mol/L. For example, 200 mM is 0.200 mol/L.
Find molar mass by adding the atomic masses in the compound’s chemical formula, accounting for each atom’s subscript. For sodium chloride, using Na = 22.990 and Cl = 35.45 g/mol gives 58.44 g/mol when rounded to two decimal places. Use the formula and chemical form actually specified: a hydrate includes its water molecules, and a salt may have a different molar mass from the uncharged compound. Do not substitute a familiar value if the reagent’s label or assigned problem specifies another form.
When preparing a solution in a lab, the target volume means the final volume after solute has been dissolved and the solution has been brought to volume. Adding the calculated mass to a full measured volume of solvent generally produces a final volume larger than the target. The calculation does not prescribe a preparation procedure; use the applicable lab method and safety guidance.
Common Mistakes and Limits
- Forgetting the mL-to-L conversion: Molarity is per litre. Using 250 as though it were litres instead of converting 250 mL to 0.250 L makes the calculated mass 1,000 times too large.
- Using the wrong concentration units: A value in mM must be divided by 1,000 to obtain mol/L before applying the formula.
- Confusing molarity with molality: Molarity uses litres of final solution; molality uses kilograms of solvent. They are different concentration measures.
- Using solvent volume instead of final volume: The formula’s volume is the volume of the complete solution, not the starting water or other solvent.
- Rounding too early: Keep extra digits through the calculation and round the final mass to a precision justified by the input values and measurement method.
The equation gives a theoretical mass from the values supplied; it cannot establish that the solute dissolves completely, that the final solution reaches the target concentration in practice, or that the entered values are correct. A measured mass can differ because of balance readability, reagent purity, absorbed moisture, or an incorrect chemical form. For a solution made by diluting a stock, the same concentration relationship can determine the amount of stock needed, but the stock concentration and final volume must be known and the dilution method must be suitable.
Frequently Asked Questions
What is the formula for mass from molarity and volume?
Use m = C × V × M: multiply molarity in mol/L by final volume in L and molar mass in g/mol. If volume is in mL, divide it by 1,000 first.
How many grams are needed for 1 M in 100 mL?
The mass depends on the solute’s molar mass. Since 100 mL is 0.100 L, the required mass is 1 mol/L × 0.100 L × M g/mol, or 0.100 × M grams.
Can I calculate mass from molarity and volume without molar mass?
You can calculate the amount in moles using n = C × V, but converting moles to grams requires the solute’s molar mass: m = n × M.
Does volume mean the amount of solvent?
No. It means the final volume of the entire solution. The solute contributes to the solution, so solvent volume and final solution volume are not interchangeable.
How do I calculate mass when concentration is in mM?
Convert millimolar to molar by dividing by 1,000, convert the final volume from mL to L, and then use m = C × V × M. Keep all units consistent.
Related
Formula used
in c | Molarity | mol/L | 0.2 | 0 in v | Final solution volume | mL | 250 | 0 in mm | Molar mass | g/mol | 58.44 | 0 out m | Mass of solute | g | c * (v / 1000) * mm | 3 out n | Amount of solute | mol | c * (v / 1000) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters Into Liters Calculator: The Missing Dimension