molecalculator

Moles & Molar Mass

Carbon Melting Point: What Temperature Does It Melt?

Calculator No. 01-3497 · Updated · Formula and assumptions shown below

Temperature in kelvin 3,823.15 K
Pressure in pascals
101,325 Pa
= Pressure × 101325
Temperature
3550 °C
Set in the form below
Pressure
1 atm
Set in the form below
You enter
Temperature (°C), Pressure, Carbon form
You get
Temperature in kelvin (K), Pressure in pascals (Pa)
Rounding
2 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Carbon does not have a single ordinary melting point at atmospheric pressure: at about 1 atmosphere, solid carbon generally changes directly into gas rather than melting into a liquid. A liquid-carbon melting temperature is meaningful only when pressure is high enough to make the liquid phase stable, and reported values depend on the pressure and the carbon form.

Formula

This page’s calculator converts an entered temperature in degrees Celsius to kelvin: T(K) = t(°C) + 273.15. Here, t is the temperature in degrees Celsius and T is the same temperature in kelvin. It also converts the selected pressure in atmospheres to pascals: P(Pa) = p(atm) × 101,325, where p is pressure in atmospheres. The conversion factor is 101,325 Pa per atmosphere.

These outputs are unit conversions, not a prediction of carbon’s melting point. The selected carbon form is included to highlight that different structures and conditions matter; it does not alter the conversion equations. Carbon’s phase boundary is not represented by one universal temperature that can be calculated from a form selection alone.

Worked Example

Using the default inputs, the entered temperature is 3550 °C and the selected pressure is 1 atm.

  • Convert temperature: 3550 + 273.15 = 3823.15 K, which rounds to 3823.15 K at two decimal places.
  • Convert pressure: 1 × 101325 = 101325 Pa.

The temperature is an illustrative input, not a claim that carbon melts at 3550 °C under 1 atm. At that pressure, carbon does not form a stable ordinary liquid phase.

Assumptions

  • The calculator performs only Celsius-to-kelvin and atmosphere-to-pascal conversions.
  • It assumes the selected pressure is expressed in standard atmospheres, with 1 atm = 101,325 Pa.
  • It does not estimate phase equilibrium, account for impurities, or distinguish specific crystal structures in its numeric outputs.

Why Carbon Has No Simple Melting Point

A melting point is the temperature at which solid and liquid forms of a substance can coexist at a specified pressure. The pressure qualification matters: phase diagrams show which state is stable as both temperature and pressure change. For many familiar materials, the pressure is understood to be close to atmospheric pressure when people quote a melting point. Carbon is an important exception to that everyday shorthand.

At ordinary atmospheric pressure, heating solid carbon leads to sublimation: it passes from solid to gas without becoming a stable bulk liquid. This is why a temperature quoted as “the melting point of carbon” without pressure and context is misleading. Temperatures sometimes repeated online—often around 3,500–3,600 °C—may describe approximate high-temperature behavior, a sublimation-related value, or a condition-dependent estimate. They should not be presented as a universal atmospheric-pressure melting point.

Carbon’s phase behavior also depends on the structure of the solid. Graphite and diamond are distinct crystalline forms, while amorphous carbon lacks the same long-range crystal order. The thermodynamic stability of these forms varies with pressure and temperature, so a phase diagram is more informative than one isolated number.

When Liquid Carbon Can Exist

At sufficiently high pressures, liquid carbon can become a stable phase. The solid–liquid boundary then depends on pressure, and the transition temperature is not a fixed property independent of conditions. High-pressure carbon research uses specialized methods because the relevant conditions are extreme and measurements are difficult; estimates and reported transition points can vary with experimental technique and interpretation.

Consequently, a responsible answer to “What is carbon’s melting point?” is: at about 1 atm, carbon generally sublimes rather than melts; under pressure high enough to stabilize liquid carbon, its melting temperature depends on the pressure and phase conditions. A value without those details is incomplete.

Carbon Forms and Comparisons

Graphite and diamond are both made of carbon atoms, but their atoms are connected in different arrangements. Those structures affect stability and transformations. Graphite is the stable form under ordinary surface conditions, while diamond is favored at higher pressures. Amorphous carbon includes materials with varied structures, so it is not a single uniform crystalline phase with one sharply defined melting point.

Carbon should not be confused with a carbon-containing substance such as carbon dioxide. Carbon dioxide has its own phase behavior and, at atmospheric pressure, does not simply melt into a liquid; its solid form (dry ice) sublimates. Likewise, the melting point of a carbon compound cannot be used as the melting point of elemental carbon.

Common Misconceptions and Practical Meaning

  • “Carbon melts at 3,550 °C.” This lacks a pressure qualification and is not an ordinary atmospheric-pressure melting point.
  • “All carbon forms behave identically.” Graphite, diamond, and amorphous carbon differ structurally, and the stable phase depends on conditions.
  • “A calculator can give the melting point from the form alone.” It cannot: a phase-boundary calculation requires reliable thermodynamic data and specified conditions.
  • “Sublimation and melting mean the same thing.” They do not. Melting is solid to liquid; sublimation is solid directly to gas.

For schoolwork or a reference table, state the pressure beside any quoted transition temperature and identify whether the value refers to melting, sublimation, or a particular experimental condition. If a precise high-pressure value is needed, consult a phase diagram or a reliable scientific source that specifies its pressure range, carbon phase, and measurement method.

Frequently Asked Questions

What is the melting point of carbon in Celsius?
There is no single conventional melting point at 1 atm because carbon generally sublimates rather than forming a stable liquid. Under high pressure, the melting temperature depends on the conditions.

Does carbon melt at 3,550 °C?
Not as a universal melting point at atmospheric pressure. Values around this range need context, especially pressure and whether the reported event is melting or sublimation.

At what pressure does carbon become liquid?
Liquid carbon is associated with high-pressure conditions, but a precise threshold depends on the phase boundary and the reference data used. A pressure-free single answer is not reliable.

Does diamond have a different melting point from graphite?
Their stability and phase behavior differ because their atomic structures differ. Under ordinary pressure, neither has a simple, standard liquid melting point; pressure and transformation pathways matter.

What does carbon do when heated at normal pressure?
It generally changes from solid to gas by sublimation rather than passing through a stable liquid phase. The exact behavior depends on the environment and the material.

Related

Formula used
in t | Temperature | °C | 3550 | -273.15
sel p | Pressure | 1 atm=1, 10 atm=10, 100 atm=100, 1000 atm=1000
sel f | Carbon form | Graphite=1, Diamond=2, Amorphous carbon=3
out c | Temperature in kelvin | K | t + 273.15 | 2
out ppa | Pressure in pascals | Pa | p * 101325 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →