molecalculator

Moles & Molar Mass

Mixing Two Solution Concentrations Calculator

Calculator No. 01-11146 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the concentration of a solution made by mixing two solutions of the same solute at different concentrations. You enter the volume and concentration of each starting solution, and it returns the final concentration (in molarity and millimolar) assuming volumes are additive and no chemical reaction occurs.

Formula

The core formula for mixing two solutions (same solute, no reaction) is:

Cfinal = (C1 × V1 + C2 × V2) / (V1 + V2)

  • C1, C2 – concentrations of the two starting solutions (in mol/L or any consistent unit)
  • V1, V2 – volumes of those solutions (in L or mL, as long as both use the same unit)
  • Cfinal – concentration of the mixture (same unit as C1 and C2)

This is a weighted average: the larger volume contributes more to the final concentration. The calculator above uses a slightly different but equivalent path: it takes the mass of solute, its molar mass, and the final volume to compute molarity directly. That is useful when you are making a solution from a solid, but for mixing two existing solutions, the formula above is the one to use. The calculator block is set up for the more common lab task of preparing a solution from a weighed solute; the mixing formula is explained here and can be applied with the same arithmetic.

Worked Example

Using the calculator defaults: you dissolve 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) in water and dilute to a final volume of 250 mL.

  1. Convert volume to liters: 250 mL = 250 / 1000 = 0.250 L
  2. Calculate moles of solute: 2.922 g ÷ 58.44 g/mol = 0.05000 mol
  3. Divide moles by volume: 0.05000 mol ÷ 0.250 L = 0.2000 mol/L

The calculator returns 0.2000 mol/L (or 200.0 mM). For mixing two solutions, say you mix 100 mL of 0.5 M NaCl with 150 mL of 0.2 M NaCl: moles = (0.5 × 0.100) + (0.2 × 0.150) = 0.050 + 0.030 = 0.080 mol; total volume = 0.250 L; final concentration = 0.080 / 0.250 = 0.32 M.

Assumptions

  • Volumes are additive – true for dilute aqueous solutions, but not for mixing ethanol and water (volume contracts).
  • No chemical reaction between the solutes – if the two solutions react, this formula is invalid.
  • Complete dissociation (for ionic solutes like NaCl) – the molarity of the salt equals the molarity of the formula unit, not individual ions.
  • Temperature and pressure are constant – concentration changes with temperature because volume changes.

How to Choose the Right Formula

There are three common scenarios in a lab:

  • Mixing two solutions of the same solute – use the weighted average formula above.
  • Diluting one solution with solvent – use C1V1 = C2V2 (a special case where one concentration is zero).
  • Preparing from a solid – use mass = molarity × molar mass × volume (as in the calculator block).

If you are mixing solutions of different solutes that do not react, the final concentration of each solute is simply its own moles divided by the total volume – they do not affect each other.

Common Mistakes and Unit Mix-Ups

  • Using different volume units – always convert both volumes to the same unit (mL or L) before applying the formula.
  • Forgetting to convert mL to L – molarity is moles per liter, so if you use mL directly, you get a number 1000 times too large.
  • Confusing molarity with molality – molarity is per liter of solution, molality is per kilogram of solvent.
  • Assuming volumes add perfectly – for concentrated solutions, especially with organic solvents, the final volume may be less than the sum.
  • Rounding too early – carry extra digits through the calculation, then round at the end.

Practical Tips for Lab Work

When mixing solutions, always add the more concentrated solution to the less concentrated one (or to solvent) slowly while stirring – this helps avoid local concentration spikes and heat effects. Use a volumetric flask for the final volume if you need high accuracy. For precise work, measure the final volume after mixing rather than assuming it is the sum of the starting volumes, especially if you are mixing solutions with different densities. Always record the temperature, because a 1 °C change in water temperature changes the volume by about 0.02%, which matters for high-precision work.

Limitations of the Simple Mixing Formula

The weighted average formula assumes ideal behavior: no volume change on mixing, no heat release or absorption, and no interaction between solute particles. For most dilute aqueous solutions (below about 0.1 M), these assumptions hold well. At higher concentrations, ionic interactions and hydration effects can cause the final concentration to differ from the calculated value by a few percent. If you are mixing strong acids or bases, always add acid to water (not water to acid) to avoid violent splashing, and remember that the pH of a mixture of an acid and a base is not simply a weighted average – you must account for the neutralization reaction. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What if I mix two solutions with different solutes?

If the solutes do not react, each one’s concentration in the final mixture is simply its own moles divided by the total volume. For example, mixing 100 mL of 0.1 M NaCl with 100 mL of 0.2 M KCl gives 0.05 M NaCl and 0.1 M KCl in the final 200 mL. If they do react (e.g., acid + base), you need a stoichiometric calculation, not a simple average.

Does the order of mixing matter?

For non-reacting solutions, mathematically no – the weighted average is the same regardless of order. In practice, adding a concentrated acid to water (not the reverse) is a safety rule because the heat released can cause splashing. For routine mixing, add the less dense solution first and stir.

Can I use this for making a dilution from a stock solution?

Yes, that is a special case where one solution is the stock and the other is pure solvent (concentration 0). The formula reduces to Cfinal = Cstock × Vstock / Vtotal, which is exactly the C1V1 = C2V2 equation.

What is the difference between molarity and molality?

Molarity (M) is moles of solute per liter of solution; molality (m) is moles of solute per kilogram of solvent. Molarity changes with temperature because liquid volumes expand, while molality does not. For dilute aqueous solutions, the numerical values are nearly the same, but for precise work, use molality if temperature varies.

Why does the calculator ask for mass and molar mass instead of just concentrations?

This particular calculator is set up for preparing a solution from a solid solute, which is a common task. For mixing two existing solutions, you can use the formula in the text and do the arithmetic manually, or you can adapt the calculator by entering the total mass of solute and the final volume – but the weighted average formula is more direct for mixing.

How do I account for the volume change when mixing ethanol and water?

You cannot use the simple additive formula because the final volume is less than the sum of the individual volumes (e.g., 50 mL ethanol + 50 mL water gives about 96 mL). Instead, you must measure the final volume after mixing, or use density tables to calculate the actual volume. For accurate concentrations, always prepare the final solution in a volumetric flask and adjust to the mark.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →