molecalculator

Moles & Molar Mass

Mixing Two Solutions of Different Percentages

Calculator No. 01-11147 · Updated · Formula and assumptions shown below

Final percentage 16.67 %
Solute mass in final mix
25.00 g
Result, rounded to 2 decimal places
Mass of solution 1
100 g
Set in the form below
Percentage of solution 1
10 %
Set in the form below
You enter
Mass of solution 1 (g), Percentage of solution 1 (%), Mass of solution 2 (g), Percentage of solution 2 (%)
You get
Final percentage (%), Solute mass in final mix (g)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Mixing two solutions of different percentages produces a final solution whose percentage concentration lies strictly between the two starting percentages, weighted by the amount of each solution used. To find the exact result, you calculate the total mass (or volume) of solute from both solutions, divide by the total mass (or volume) of the mixture, and multiply by 100.

Formula

The final percentage concentration \( p_f \) is given by:

\( p_f = \frac{m_1 \cdot p_1 + m_2 \cdot p_2}{m_1 + m_2} \)

where:

  • \( m_1 \) and \( m_2 \) are the masses of solution 1 and solution 2 (in grams or any consistent unit).
  • \( p_1 \) and \( p_2 \) are the percentage concentrations of solute in each solution (in % w/w).
  • The numerator \( m_1 \cdot p_1/100 \) gives the mass of solute in solution 1; similarly for solution 2.
  • The denominator is the total mass of the final mixture.

This formula assumes that percentages are by mass (w/w). If your percentages are by volume (v/v) or mass/volume (w/v), the calculation changes – see the section on unit types below.

Worked Example

Using the default values from the calculator: 100 g of a 10% solution mixed with 50 g of a 30% solution.

Step 1: Find the mass of solute in each solution.

  • Solution 1: 100 g × 10% = 100 × 0.10 = 10 g solute
  • Solution 2: 50 g × 30% = 50 × 0.30 = 15 g solute

Step 2: Add the solute masses: 10 + 15 = 25 g solute.

Step 3: Add the solution masses: 100 + 50 = 150 g total.

Step 4: Divide and convert to percentage: (25 / 150) × 100 = 16.67%.

The final solution is 150 g of a 16.67% solution. Notice this is closer to 10% than to 30% because you used more of the 10% solution.

Assumptions

  • Percentages are by mass (w/w) unless stated otherwise.
  • Densities are assumed to be 1 g/mL when converting volumes to masses – this is only true for dilute aqueous solutions near room temperature.
  • No chemical reaction occurs between the two solutions; the solute simply mixes.
  • The final volume is assumed to be the sum of the individual volumes only if the solutions are ideal – real solutions can contract or expand slightly.

When to Use This Calculation

This calculation is common in laboratory prep, agriculture (mixing fertilizers or pesticide sprays), food science (diluting juices or syrups), and industrial processes. For example, you might mix a 5% saline solution with a 20% saline solution to get an intermediate concentration for a buffer. The same math applies when you dilute a concentrated stock solution with pure solvent (which is a 0% solution) – the formula reduces to the standard dilution equation.

You can also use it in reverse: if you know the target percentage and the amount of one solution, you can solve for the required mass of the other. The calculator above gives the forward direction; for reverse problems, rearrange the formula algebraically.

Common Mistakes and Misconceptions

  • Using volumes instead of masses: If your percentages are w/w, you must use masses. If you only have volumes, you need densities to convert. Many people mistakenly use mL as if they were grams, which works only for water-like solutions.
  • Ignoring the percentage unit: A 10% solution means 10 g of solute per 100 g of solution, not 10 g per 100 mL of solvent. Always read the label carefully.
  • Assuming the final concentration is the average: The final percentage is a weighted average, not a simple arithmetic mean. Mixing equal masses of 10% and 30% gives 20%, but mixing unequal masses shifts the result toward the larger mass.
  • Forgetting to convert percentages to decimals: In the formula, you must divide the percentage by 100 before multiplying by mass.

Percentage Types: w/w, v/v, and w/v

Percent concentration can be expressed in three ways:

  • % w/w (mass/mass): grams of solute per 100 g of solution. This is the most common for solid solutes dissolved in liquids. The formula above works directly.
  • % v/v (volume/volume): mL of solute per 100 mL of solution. Used for liquid-liquid mixtures like alcohol in water. Here you can use volumes directly in the same formula, but only if volumes are additive (which is often not true for alcohol-water mixtures).
  • % w/v (mass/volume): grams of solute per 100 mL of solution. This is common in biology and medicine. To mix two w/v solutions, you must use the formula: (V1×C1 + V2×C2) / (V1+V2) where C is in g/mL, but the final volume may not equal V1+V2 due to volume changes.

Always check which type you are dealing with. The calculator above is for w/w; if you have w/v, convert to w/w using density.

How to Choose the Right Amounts

Suppose you need 200 g of a 15% solution, and you have a 10% and a 30% solution. You can use the formula to find the masses needed. Let \( x \) be the mass of the 10% solution and \( 200 – x \) be the mass of the 30% solution. Then:

\( 0.10x + 0.30(200 – x) = 0.15 \times 200 \)

Solving: \( 0.10x + 60 – 0.30x = 30 \) → \( -0.20x = -30 \) → \( x = 150 \) g of 10% solution and 50 g of 30% solution.

This is a classic “alligation” problem. The ratio of the two solutions is inversely proportional to the difference between the target and each starting percentage. In this example, the target (15%) is 5 points away from 10% and 15 points away from 30%, so you need 3 times more of the 10% solution (15/5 = 3).

Practical Considerations and Safety

When mixing solutions, always add acid to water (not water to acid) if one of the solutions is a strong acid – this prevents dangerous splattering. Wear appropriate personal protective equipment (gloves, goggles, lab coat) and work in a well-ventilated area. Follow your lab’s standard operating procedures and the safety data sheet (SDS) for each chemical. If the solutions are reactive with each other (e.g., acid and bleach), do not mix them without specific training. The calculation above assumes no chemical reaction, only physical mixing.

For very precise work, account for temperature: densities change with temperature, so a w/w percentage is temperature-independent, but w/v percentages are not. If you need high accuracy, prepare solutions by mass rather than volume.

Frequently Asked Questions

Can I mix a 10% and a 30% solution to get exactly a 20% solution? Yes, but only if you mix equal masses of each. For example, 100 g of each gives 200 g total with 20 g + 30 g = 50 g solute, which is 25%? Wait – let’s recalculate: 100 g of 10% has 10 g solute; 100 g of 30% has 30 g solute; total solute = 40 g; total mass = 200 g; 40/200 × 100 = 20%. Yes, equal masses give exactly the average.

What if I mix a solution with pure water (0%)? The formula still works: set p2 = 0. For example, mixing 50 g of a 20% solution with 50 g of water gives (50×0.20 + 50×0) / 100 × 100 = 10%. This is a dilution.

Does the final volume equal the sum of the individual volumes? Not always. For many aqueous solutions, volumes are nearly additive, but for alcohol-water mixtures, the total volume is less than the sum due to molecular packing. If you need an exact final volume, use a volumetric flask and add solvent to the mark.

How do I mix solutions with different densities? If your percentages are w/w, you must use masses. If you only have volumes, convert each volume to mass using its density (mass = volume × density). For example, 100 mL of a solution with density 1.1 g/mL has a mass of 110 g.

Why is the final percentage not just the average of the two percentages? Because the average ignores the different amounts of each solution. The final concentration is a weighted average, where the weights are the masses of each solution. The more solution you use, the more it pulls the result toward its own percentage.

Can I use this calculator for molarity (mol/L) instead of percentage? No, molarity is moles per liter, and mixing two molar solutions requires a different formula: M1V1 + M2V2 = Mf(V1+V2), assuming volumes are additive. This works only for ideal solutions and when no volume change occurs. For accurate work, use a volumetric flask.

Related

Formula used
in m1 | Mass of solution 1 | g | 100 | 0
in p1 | Percentage of solution 1 | % | 10 | 0
in m2 | Mass of solution 2 | g | 50 | 0
in p2 | Percentage of solution 2 | % | 30 | 0
out pf | Final percentage | % | (m1*p1/100 + m2*p2/100) / (m1+m2) * 100 | 2
out sf | Solute mass in final mix | g | m1*p1/100 + m2*p2/100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →