molecalculator

Moles & Molar Mass

Mm to Radius Converter: Convert Diameter to Radius

Calculator No. 01-2802 · Updated · Formula and assumptions shown below

Radius 5.000 mm
Radius
0.500 cm
= Radius ÷ 10
Radius
0.005000 m
= Radius ÷ 1000
Radius
0.1969 in
= Radius ÷ 25.4
You enter
Diameter (mm)
You get
Radius (mm), Radius (cm), Radius (m), Radius (in)
Rounding
3 dp · 6 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A millimeter (mm) is a unit of length, while radius describes the distance from a circle’s center to its edge. If you know a circle’s diameter in millimeters, divide it by 2 to get its radius in millimeters; this calculator converts that diameter to radius and also reports the equivalent radius in other units.

Formula

Radius is half the diameter:

r = d / 2

  • d is the circle’s diameter in millimeters (mm).
  • r is its radius in millimeters (mm).

The additional outputs convert that radius: centimeters = millimeters / 10, meters = millimeters / 1,000, and inches = millimeters / 25.4. The international inch is exactly 25.4 mm. These are unit conversions; they do not change the circle’s size.

Worked Example

For the default diameter of 10 mm:

r = d / 2 = 10 mm / 2 = 5.000 mm

  • Centimeters: 5.000 mm / 10 = 0.500 cm
  • Meters: 5.000 mm / 1,000 = 0.005000 m
  • Inches: 5.000 mm / 25.4 = 0.1969 in

The radius is 5.000 mm. The other values are the same length expressed in different units.

Assumptions

  • The input is a diameter, not a radius.
  • The shape is a circle, so its radius is exactly half its diameter.
  • The input is a nonnegative length measured in millimeters.
  • Displayed values are rounded; calculations use the entered diameter.

What “Mm to Radius” Means

The phrase “mm to radius” is ambiguous because millimeters are units, whereas radius is a geometric measurement. A unit alone cannot be converted into a radius: you need a length value and must know what that value represents. In common searches, people may mean “convert a diameter given in millimeters to its radius.” For that task, halve the diameter.

If you already have the radius in millimeters, no geometric conversion is needed. Entering that radius as the calculator’s diameter would halve it incorrectly. Check whether your drawing, measurement, or specification labels the value as radius, diameter, or a circle’s width before calculating.

How to Use the Converter

  1. Find the circle’s diameter, the distance across it through its center, in millimeters.
  2. Enter that value in the Diameter field.
  3. Read the first result for radius in millimeters, or use the additional outputs for centimeters, meters, and inches.

The input must be zero or greater because a physical diameter cannot be negative. A zero diameter gives a zero radius; real circles normally have a positive diameter. The calculator does not impose a maximum, but very large measurements should still be checked against the measurement method and the intended application.

Diameter, Radius, and Other Circle Measurements

The radius is the distance from the center of a circle to its circumference. The diameter passes through the center from one side to the other, making it twice the radius. A line across a circle that does not pass through the center is a chord, not necessarily the diameter.

For example, a circular opening 24 mm across has a radius of 12 mm. Conversely, if a specification gives a radius of 12 mm, its diameter is 24 mm. This distinction matters because formulas use these measurements differently:

  • Circumference: C = 2 × pi × r, or C = pi × d.
  • Area: A = pi × r2, or A = pi × (d / 2)2.

For a diameter of 10 mm, the radius is 5 mm, the circumference is about 31.416 mm, and the area is about 78.540 mm2. The area uses square millimeters, not millimeters. The converter reports radius only; circumference and area are included here to clarify why confusing radius and diameter can have a larger effect in other calculations.

Accuracy, Rounding, and Common Mistakes

Keep the original measurement’s precision in mind. If a diameter was measured as 10 mm to the nearest millimeter, reporting a radius of 5.000 mm does not make the underlying measurement accurate to a thousandth of a millimeter. The extra digits in calculator output are useful for unit conversion, but they cannot add precision that the measurement did not have.

  • Halving the wrong value: Divide only a diameter by 2. A radius is already the center-to-edge distance.
  • Mixing units: Convert all lengths to a common unit before using them together. For example, do not combine a radius in millimeters with a diameter in centimeters without conversion.
  • Using a width that misses the center: Only the circle’s full diameter is twice the radius. An off-center chord is shorter.
  • Rounding too early: Keep the unrounded radius for subsequent area or circumference calculations, then round the final result appropriately.
  • Confusing mm and Mm: In standard SI notation, lowercase mm means millimeter. Uppercase M is the prefix mega, so Mm denotes a megameter, not a millimeter. Search queries often use capitalization casually, but technical writing should distinguish them.

For a physical object that is not perfectly circular, one diameter may not describe every direction. Measure across the center in the direction relevant to your application, or take multiple measurements if the object’s shape needs to be assessed. This simple converter assumes an ideal circle and does not estimate measurement uncertainty or compensate for an irregular edge.

Frequently Asked Questions

How do I convert mm to radius?
Millimeters do not convert to radius by themselves. If the millimeter value is a circle’s diameter, divide it by 2. For example, a 16 mm diameter has an 8 mm radius.

What is the radius of a 10 mm circle?
If 10 mm is the diameter, the radius is 5 mm. If 10 mm is already the radius, the diameter is 20 mm.

How do I convert a radius in mm to a diameter?
Multiply the radius by 2. A radius of 7 mm corresponds to a diameter of 14 mm.

How many inches is a radius in millimeters?
Divide the radius in millimeters by 25.4 to get inches. For instance, 5 mm is approximately 0.1969 inches.

Does “mm to radius” mean millimeters to millimeters?
Not exactly. Millimeters are a unit, and radius is a type of measurement. You need to know a circle’s diameter or radius before finding the other measurement.

Related

Formula used
in d | Diameter | mm | 10 | 0
out r | Radius | mm | d / 2 | 3
out cm | Radius | cm | r / 10 | 3
out m | Radius | m | r / 1000 | 6
out in | Radius | in | r / 25.4 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →