molecalculator

Moles & Molar Mass

Molar Mass of Glucose, Urea & Sucrose

Calculator No. 01-9884 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The molar masses are: glucose (C6H12O6) = 180.156 g/mol, urea (CH4N2O) = 60.056 g/mol, and sucrose (C12H22O11) = 342.296 g/mol. Enter the mass of any of these solutes and a final solution volume below to get its molarity, or use the calculator to convert between grams and moles for any compound.

Formula

Molarity (c) is the amount of solute in moles divided by the volume of solution in liters:

c = m / (M × V)

where:

  • c = molarity (mol/L, written M)
  • m = mass of solute (g)
  • M = molar mass of the solute (g/mol)
  • V = final solution volume (L) — note that you must convert mL to L by dividing by 1000

For a solid solute, the mass is measured on a balance, the molar mass comes from the chemical formula, and the volume is the final volume of the solution after the solid has dissolved and you have added solvent up to the mark.

Worked Example

Using the default values in the calculator: you have 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) and you prepare 250 mL of solution.

  1. Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
  2. Convert mass to moles: 2.922 g ÷ 58.44 g/mol = 0.05000 mol (exactly 0.05 mol)
  3. Divide moles by volume: 0.05000 mol ÷ 0.250 L = 0.2000 mol/L

The calculator shows 0.2000 M (or 200.0 mM). This is a standard 0.2 M NaCl solution, often used in biology labs as a saline or dilution stock.

Assumptions

  • The solute is pure and dry (no water of hydration unless specified).
  • The solution is ideal and dilute enough that volume changes on mixing are negligible.
  • The volume entered is the final volume of the solution, not the volume of solvent added.
  • Temperature is not a factor for molarity based on mass and final volume at the preparation temperature.

Background: Why These Three Molecules?

Glucose, urea, and sucrose are three of the most common solutes in chemistry and biology teaching labs. Glucose is a monosaccharide (a simple sugar) and the main energy source for cells. Urea is a small nitrogen-containing compound that is the chief nitrogenous waste product in mammals. Sucrose is a disaccharide made of glucose and fructose — ordinary table sugar. Each has a distinct molar mass, and knowing those values lets you prepare precise solutions for experiments, whether you are making a sugar gradient, a urea denaturation buffer, or a sucrose density gradient.

The molar mass of a compound is simply the sum of the atomic weights of all atoms in its formula, using the IUPAC standard atomic weights. For glucose (C6H12O6): 6×12.011 + 12×1.008 + 6×15.999 = 180.156 g/mol. For urea (CH4N2O): 12.011 + 4×1.008 + 2×14.007 + 15.999 = 60.056 g/mol. For sucrose (C12H22O11): 12×12.011 + 22×1.008 + 11×15.999 = 342.296 g/mol.

How to Use the Calculator

To use the calculator for glucose, urea, or sucrose, simply replace the default molar mass (58.44, which is NaCl) with the value for your compound:

  • Glucose: 180.156 g/mol
  • Urea: 60.056 g/mol
  • Sucrose: 342.296 g/mol

Then enter the mass you weighed out and the final volume you want. The calculator returns molarity in mol/L and in mmol/L. For example, to make 500 mL of 0.5 M glucose, you would need 0.5 mol/L × 0.5 L × 180.156 g/mol = 45.039 g of glucose. The calculator can also be used backward: if you know the desired molarity and volume, you can solve for mass by rearranging the formula (m = c × M × V).

Common Mistakes and Misconceptions

A frequent error is confusing molarity (mol/L) with molality (mol/kg of solvent). Molarity depends on the final solution volume, which changes slightly with temperature, while molality depends on the mass of solvent, which is temperature-independent. For dilute aqueous solutions, the numerical difference is small, but for concentrated solutions (like 5 M NaCl) it matters.

Another mistake is using the volume of solvent added instead of the final volume. If you dissolve a solid in 250 mL of water, the final volume might be 253 mL because the solute occupies space. Always use a volumetric flask and add solvent to the mark to get the exact final volume.

A third misconception: the molar mass of a hydrated salt (like CuSO4·5H2O) includes the water molecules. If you use the anhydrous molar mass for a hydrated compound, your molarity will be too high. The calculator’s molar mass input lets you enter the correct value for your specific reagent.

Comparing Glucose, Urea, and Sucrose

These three compounds illustrate how molecular size affects molar mass. Urea (60 g/mol) is a small molecule; glucose (180 g/mol) is about three times heavier; sucrose (342 g/mol) is nearly twice as heavy as glucose. This matters in experiments that rely on molar concentration, such as osmotic pressure, freezing point depression, or enzyme kinetics. A 1 M solution of each contains the same number of molecules (6.022 × 1023 per liter) but very different masses: 60 g for urea, 180 g for glucose, and 342 g for sucrose. If you need equal numbers of molecules, you must weigh out these different masses.

In biology, sucrose is often used in density gradients because its solutions are dense and relatively inert. Glucose is a common carbon source in microbial media. Urea is used to denature proteins in biochemistry. Each requires accurate molar mass for preparing stock solutions.

Practical Tips for Preparing Solutions

  1. Always use a calibrated balance and weigh the solute directly into a beaker or weighing boat.
  2. Dissolve the solute in about 70-80% of the final volume of distilled or deionized water.
  3. Stir or swirl until fully dissolved — glucose and sucrose dissolve easily, urea dissolves with a cooling effect.
  4. Transfer to a volumetric flask and bring to the mark with solvent. Mix thoroughly by inverting.
  5. Record the temperature, as volumetric glassware is calibrated at a specific temperature (usually 20 °C).

For accurate work, use analytical grade reagents and follow your lab method, the safety data sheet (SDS) and your supervisor.

Limitations of the Calculator

This calculator assumes the solute is a pure solid with a known molar mass. It does not account for:

  • Purity of the reagent (if it is 98% pure, you need to weigh more).
  • Water of hydration (as mentioned).
  • Non-ideal behavior in very concentrated solutions (activity coefficients).
  • Volume changes on mixing (for most dilute solutions, these are negligible).

For most teaching and research applications, these effects are small. If you need high precision, you should determine the exact concentration by titration or other analytical methods.

Frequently Asked Questions

What is the molar mass of glucose in g/mol? Glucose (C6H12O6) has a molar mass of 180.156 g/mol. This is the sum of 6 carbon atoms (12.011 each), 12 hydrogen atoms (1.008 each), and 6 oxygen atoms (15.999 each).

How do I calculate the molar mass of urea? Urea has the formula CH4N2O. Add the atomic weights: 1×12.011 (C) + 4×1.008 (H) + 2×14.007 (N) + 1×15.999 (O) = 60.056 g/mol. You can also look it up, but it is easy to compute.

Is sucrose molar mass the same as glucose? No. Sucrose (C12H22O11) has a molar mass of 342.296 g/mol, which is almost double that of glucose (180.156 g/mol). Sucrose is a disaccharide made of glucose and fructose, so it has more atoms.

How many grams of glucose do I need for 1 L of 1 M solution? Multiply molarity by volume by molar mass: 1 mol/L × 1 L × 180.156 g/mol = 180.156 g. Weigh out 180.156 g of glucose and dissolve to a final volume of 1 L.

What is the difference between molar mass and molecular weight? They are numerically the same, but molar mass has units of g/mol and is the mass of one mole of a substance, while molecular weight is a dimensionless ratio of the average mass of a molecule to 1/12 the mass of carbon-12. In practice, chemists use the terms interchangeably.

Can I use this calculator for other compounds? Yes, any solid solute with a known molar mass. Just replace the default molar mass with the value for your compound. The calculator works for any substance where you know the mass and final volume.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →