molecalculator

Moles & Molar Mass

Molarity of Pure Sulfuric Acid: Calculator and Formula

Calculator No. 01-2890 · Updated · Formula and assumptions shown below

Molarity 18.6582 mol/L
Molar concentration
0.018658 mol/mL
= Molarity ÷ 1000
H2SO4 mass fraction
1 fraction
Set in the form below
Solution density
1.83 g/mL
Set in the form below
You enter
H2SO4 mass fraction (fraction), Solution density (g/mL), Molar mass of H2SO4 (g/mol)
You get
Molarity (mol/L), Molar concentration (mol/mL)
Rounding
4 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Pure sulfuric acid (H2SO4) is about 18.4 mol/L at 20 °C, using a density of approximately 1.83 g/mL and a molar mass of 98.08 g/mol. This calculator estimates molarity from acid mass fraction and solution density; enter those values to get mol/L and mol/mL. “Pure” here means the concentrated reagent is treated as 100% H2SO4, not that it is a separate liquid with a concentration independent of temperature and density.

Formula

Molarity is the amount of dissolved substance, in moles, divided by the final solution volume in liters. When mass fraction and density are known, the equivalent calculation is:

M = (w × ρ × 1000) / MM

  • M is molarity in mol/L.
  • w is the mass fraction of H2SO4, expressed from 0 to 1. For 98% acid, enter 0.98.
  • ρ is solution density in g/mL.
  • 1000 converts the mass of one milliliter of solution to the mass of one liter, since 1 L = 1000 mL.
  • MM is the H2SO4 molar mass in g/mol. With abridged standard atomic weights H = 1.008, S = 32.06, and O = 15.999, MM = 2(1.008) + 32.06 + 4(15.999) = 98.072 g/mol, conventionally rounded here to 98.08 g/mol.

For a genuinely pure sample, w = 1. The calculation assumes the entered density applies at the temperature of interest. The calculator reports mol/mL as a secondary unit; 1 mol/mL equals 1000 mol/L, so this is a small number and is generally less convenient than molarity.

Worked Example

Using the calculator defaults—mass fraction 1, density 1.83 g/mL, and molar mass 98.08 g/mol—the mass of one liter is:

1.83 g/mL × 1000 mL/L = 1830 g/L.

The amount of H2SO4 in that mass is 1830 g/L ÷ 98.08 g/mol = 18.657 mol/L. Equivalently, (1 × 1.83 × 1000) ÷ 98.08 = 18.657 mol/L, displayed to four decimal places as 18.6566 mol/L. The secondary output is 18.6566 ÷ 1000 = 0.0186566 mol/mL, displayed to six decimal places as 0.018657 mol/mL.

Assumptions

  • The input density is an approximate value of 1.83 g/mL; density varies with temperature and composition. The result is therefore an estimate, not a temperature-independent constant.
  • The default mass fraction of 1 treats the sample as pure H2SO4. Commercial concentrated acid is commonly about 98% by mass, so it is not pure acid.
  • The calculation is concentration arithmetic only. It does not account for volume contraction or expansion during mixing; density is used for the final solution being described.

Why Pure Acid Is About 18.4 M

A liter of sulfuric acid at density 1.83 g/mL has a mass of about 1830 g. Dividing that by roughly 98.08 g for each mole gives about 18.7 moles per liter. A commonly quoted reference value is around 18.4 M, based on a density near 1.84 g/mL and a molar mass near 98.08 g/mol. Those approximate figures do not produce exactly the same result: (1.84 × 1000) ÷ 98.08 is about 18.76 M. This illustrates why a stated density, temperature, purity, and molar mass convention matter when a precise answer is needed.

For classroom and general reference purposes, “about 18.4 M” or “about 18.7 M” can both appear depending on the density value and rounding used. Do not treat either as an exact universal constant. For calculations that depend on accuracy, use the reagent’s certified mass fraction and density data at the relevant temperature, or use its stated concentration.

Pure Acid Versus Concentrated Acid

Concentrated sulfuric acid is often sold at roughly 98% H2SO4 by mass. Its molarity is not obtained by multiplying the pure-acid value by 0.98 alone: the density of the 98% solution must also be included. For illustration, using 0.98 mass fraction and a density of 1.84 g/mL gives (0.98 × 1.84 × 1000) ÷ 98.08 ≈ 18.39 mol/L. This is an example based on those specified inputs, not a universal specification for every bottle or temperature.

Mass percent and molarity describe different things. Mass percent is grams of acid per 100 g of solution; molarity is moles of acid per liter of solution. Converting between them requires density because a mass does not by itself tell you the solution’s volume. For 98% acid, 100 g of solution contains 98 g of H2SO4, but that is not 100 mL of solution.

When This Calculation Is Useful—and Its Limits

This conversion is useful when comparing a reagent label given in mass percent with a calculation requiring mol/L, or when checking a textbook estimate for concentrated sulfuric acid. It can also show why a small volume of concentrated acid represents a substantial number of moles. For dilute aqueous solutions, a stated molarity is usually more directly useful than converting from mass fraction and density.

  • Use mass fraction, not a percent number: enter 0.98 for 98%, not 98.
  • Use density in g/mL, not kg/L or g/L. Although 1 g/mL and 1 kg/L are numerically equivalent, the calculator expects g/mL.
  • Use the density for the actual composition and temperature. Density changes as temperature changes, which changes the calculated molarity per liter.
  • Keep enough significant figures in inputs. Reporting many calculator decimals does not make approximate density data highly precise.

The formula determines analytical molarity from the amount of H2SO4 present and the solution volume. It does not calculate pH, acid activity, or the concentration of each ionic species after dissociation. Sulfuric acid is diprotic, but that does not mean its molarity should be doubled: one mole of H2SO4 is one mole of sulfuric acid formula units. The number of acid equivalents depends on the reaction and how many protons are involved.

Safety

Sulfuric acid is highly corrosive and can cause severe burns. This calculator is for study and lab-planning arithmetic, not instructions for preparing or handling acid. Do not infer that a calculated concentration makes a substance safe to handle. For any bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. The calculator does not replace training, suitable protective measures, or local safety procedures.

Frequently Asked Questions

What is the molarity of pure sulfuric acid?
It is approximately 18.4–18.7 mol/L in commonly cited estimates, depending on the density and temperature assumed. Use a specified density and purity for a more defensible calculated value.

Is concentrated sulfuric acid 18 M?
It is often described as roughly 18 M. A typical concentrated solution is near 98% by mass, and its exact molarity depends on its density, composition, and temperature.

Why is density needed to calculate molarity?
Molarity is moles per liter, while mass fraction gives acid mass per solution mass. Density converts the solution’s mass into its volume, making the conversion possible.

Does one mole of sulfuric acid equal two moles?
No. One mole of H2SO4 is one mole of sulfuric acid. It can supply two acidic protons in appropriate reactions, but that affects equivalents, not the substance’s molarity.

Is 98% sulfuric acid pure?
No. A 98% mass fraction means 98 g of H2SO4 in every 100 g of solution; the remaining mass is principally water. It is concentrated, but not pure.

Related

Formula used
in w | H2SO4 mass fraction | fraction | 1 | 0 | 1
in d | Solution density | g/mL | 1.83 | 0.001
in mm | Molar mass of H2SO4 | g/mol | 98.08 | 0.001
out c | Molarity | mol/L | (w * d * 1000) / mm | 4
out cm | Molar concentration | mol/mL | c / 1000 | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →