RCF and g-force describe the same thing in centrifugation: relative centrifugal force, expressed as a multiple of Earth’s gravitational acceleration. RPM is different: it measures how fast the rotor turns, and the RCF produced at that speed depends on the rotor’s radius.
Formula
The calculator uses RCF = 1.118 × 10−5 × r × n2, where RCF is relative centrifugal force in multiples of standard gravity (× g), r is the radius in centimetres from the axis of rotation to the sample, and n is rotor speed in revolutions per minute (rpm). The numerical factor incorporates the conversion from rpm and centimetres to acceleration relative to standard gravity. The output is a dimensionless multiple: an RCF of 2,795 × g means an acceleration 2,795 times standard gravity, not a force measured in newtons.
To calculate speed from a target RCF, rearrange the same equation: n = √(RCF ÷ (1.118 × 10−5 × r)). This page’s calculator takes radius and rpm as inputs and reports RCF; use the rearranged equation when you know the desired RCF and need an rpm setting.
Worked Example
Using the defaults—radius 10 cm and speed 5,000 rpm:
- Square the speed: 5,0002 = 25,000,000 rpm2.
- Multiply by the radius: 10 × 25,000,000 = 250,000,000 cm·rpm2.
- Apply the conversion factor: 1.118 × 10−5 × 250,000,000 = 2,795 × g.
The calculator therefore reports an RCF of 2,795 × g at 5,000 rpm for a 10 cm radius.
Assumptions
- The radius is measured in centimetres from the rotation axis to the point in the sample whose RCF is wanted.
- The rotor turns at a steady stated speed; the calculation does not account for acceleration or deceleration.
- RCF is reported relative to standard gravity, approximately 9.80665 m/s2.
- The formula gives the local RCF at the radius entered. A sample extending across a range of radii experiences a range of RCF values.
How RCF and g-force relate
“RCF” stands for relative centrifugal force. In manuals and protocols, “× g” or “g-force” is the common way of writing its value. For example, 3,000 × g and an RCF of 3,000 refer to the same relative acceleration. The “g” here is a reference to gravitational acceleration; it does not mean grams, and RCF is not a mass or a direct measure of the force acting on a particular particle.
A centrifuge creates this acceleration by rotating a sample around an axis. In a simple description, the acceleration increases with the distance from the axis and with the square of rotational speed. That squared relationship matters: increasing rpm by 10% increases RCF by about 21%, if the radius stays the same. Doubling rpm gives four times the RCF.
For a fixed rotor and sample position, rpm and RCF are therefore convertible. But the same rpm on two rotors does not necessarily produce the same RCF because their radii can differ. A protocol that gives only rpm may not transfer directly between rotor designs.
How to find the correct radius
Use the radius specified for the rotor or the distance from its rotational axis to the sample location relevant to your protocol. It is not automatically the rotor’s outside diameter: radius is a distance from the axis, so it is half a diameter only when that diameter is measured through the axis to the same point.
- Fixed-angle rotor: the sample is held at an angle. The rotor manual may specify a maximum, average, or another reference radius; use the radius convention required by the protocol.
- Swinging-bucket rotor: the bucket moves outward during rotation. A protocol may refer to the maximum radius at the bottom of the bucket or to a defined sample position.
- Sample with appreciable height: the top and bottom of the liquid can be at different radii, so their local RCF values differ. A protocol’s specified radius is more useful than choosing one arbitrarily.
Do not substitute a radius from a different rotor merely because the rotor fits the same centrifuge. If the required radius or RCF convention is unclear, consult the rotor documentation or the method that specifies the run.
Choosing RCF or rpm
When comparing protocols or moving a method to a different rotor, RCF is usually the more portable value because it describes acceleration at a defined radius. RPM is still necessary for operating a centrifuge, but the rpm required to reach a target RCF depends on the chosen rotor’s effective radius.
For instance, a target of 2,795 × g at a 10 cm radius corresponds to 5,000 rpm. At a 5 cm radius, reaching the same RCF requires a higher speed: √(2,795 ÷ (1.118 × 10−5 × 5)) ≈ 7,071 rpm. These values are an illustration of the conversion, not a recommendation for a particular rotor or sample.
Before running a centrifuge, check the rotor’s rated maximum speed and the instrument’s limits. A calculated speed must never be treated as permission to exceed a limit. Also verify that the rotor, tubes, adapters, and sample conditions are compatible with the intended run. Follow your lab method, the safety data sheet (SDS) and your supervisor.
Common mistakes and limitations
- Confusing rpm with RCF: rpm is rotational speed; RCF is relative acceleration. They are related, but they are not interchangeable numbers.
- Entering millimetres as centimetres: this makes the calculated RCF ten times too small. Convert millimetres to centimetres by dividing by 10.
- Using diameter instead of radius: entering a diameter doubles the radius input and doubles the calculated RCF. Measure from the axis to the relevant point.
- Ignoring which point in the sample is meant: RCF varies with radius. Values described as maximum, average, or minimum RCF may differ for the same run.
- Assuming equal RCF means identical separation: separation also depends on sample properties, rotor geometry, run time, temperature, and other method conditions. RCF alone does not predict a complete outcome.
The standard conversion factor uses standard gravity and the stated radius convention. It does not calculate sedimentation time, rotor performance, sample heating, or whether a particular container or rotor is safe at a selected speed. Treat the result as a conversion aid, then check the equipment limits and the protocol.
Frequently Asked Questions
Is RCF the same as g-force?
Yes. In centrifuge settings, RCF and a value written as “× g” describe relative centrifugal acceleration. A value of 1,000 × g means 1,000 times standard gravitational acceleration.
What is the difference between RCF and rpm?
RPM counts rotor revolutions per minute. RCF describes the resulting acceleration relative to gravity and depends on both rpm and the radius at which it is calculated.
How do I convert rpm to RCF?
Use RCF = 1.118 × 10−5 × radius in cm × rpm2. Use the radius specified for the sample position and rotor, not an unrelated rotor dimension.
Can I use the same rpm on a different centrifuge?
Not necessarily. A different rotor radius can produce a different RCF at the same rpm. Compare the target RCF and the relevant rotor radius, and stay within all equipment limits.
Does a higher RCF always mean a better result?
No. The suitable RCF depends on the sample and method. Higher acceleration is not automatically appropriate and may affect sample quality or exceed equipment limits.
Related
Formula used
in r | Rotor radius to sample | cm | 10 | 0 in n | Rotor speed | rpm | 5000 | 0 out rcf | Relative centrifugal force | × g | 1.118e-5 * r * n ^ 2 | 0 out rpm | Rotor speed | rpm | n | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp