This calculator converts the electrical frequency (hertz, Hz) of an AC induction motor into its rotational speed (revolutions per minute, RPM). You enter the supply frequency, the number of motor poles, and (optionally) the slip percentage, and it returns the synchronous speed and the actual full-load speed.
Formula
The core relationship for an AC induction motor is:
Synchronous speed (RPM) = (120 × Frequency in Hz) / Number of poles
Where:
- Frequency (f) – the AC supply frequency in hertz (Hz). Common values are 50 Hz (most of the world) and 60 Hz (North America, parts of South America and Asia).
- Number of poles (p) – the total number of magnetic poles the motor stator is wound for. This is always an even integer (2, 4, 6, 8, …).
- Synchronous speed (Ns) – the speed of the rotating magnetic field, in revolutions per minute (RPM).
The constant 120 comes from converting seconds to minutes (60) and accounting for the fact that one electrical cycle corresponds to two pole passes (2). So 60 × 2 = 120.
For the actual full-load speed, you also need slip:
Actual speed = Synchronous speed × (1 – Slip / 100)
Slip (s) is the percentage difference between synchronous speed and rotor speed. It is typically 2–5% for standard induction motors at full load.
Worked Example
Using the default values from the calculator – frequency = 50 Hz, poles = 4, slip = 3%:
- Synchronous speed: Ns = (120 × 50) / 4 = 6000 / 4 = 1500 RPM
- Actual full-load speed: N = 1500 × (1 – 3/100) = 1500 × 0.97 = 1455 RPM
The calculator shows 1500 RPM for synchronous speed and 1455 RPM for actual speed, matching the steps above.
Assumptions
- The motor is a standard AC induction motor (asynchronous).
- The number of poles is an even integer and is the total pole count, not pole pairs.
- Slip is expressed as a percentage of synchronous speed.
- The supply frequency is constant (not a variable-frequency drive output with harmonics).
Why This Matters: Synchronous vs. Actual Speed
Many people confuse the two speeds. The synchronous speed is the speed of the rotating magnetic field – it is a theoretical value. The rotor never actually reaches it in an induction motor because it needs slip to induce current in the rotor bars. If the rotor ran at exactly synchronous speed, there would be no relative motion between the field and rotor, no induced current, and no torque. So the actual speed is always slightly lower than synchronous speed.
For example, a 4-pole motor on 60 Hz has a synchronous speed of (120 × 60) / 4 = 1800 RPM. With 3% slip, the actual full-load speed is 1800 × 0.97 = 1746 RPM. This is why a motor nameplate might say “1745 RPM” – that is the full-load speed, not the synchronous speed.
How to Choose the Right Motor Poles
If you know the desired speed and your supply frequency, you can work backward to find the number of poles needed:
- For 50 Hz: 2 poles → 3000 RPM; 4 poles → 1500 RPM; 6 poles → 1000 RPM; 8 poles → 750 RPM.
- For 60 Hz: 2 poles → 3600 RPM; 4 poles → 1800 RPM; 6 poles → 1200 RPM; 8 poles → 900 RPM.
These are synchronous speeds. The actual full-load speeds will be a few percent lower. When selecting a motor, always check the nameplate for the rated speed – it already accounts for slip at rated load.
Common Mistakes and Misconceptions
- Using pole pairs instead of poles: Some formulas use “pole pairs” (p/2). If you use the number of pole pairs directly, the formula becomes (120 × f) / (2 × pole pairs). Always confirm which one you have.
- Ignoring slip: For actual speed, slip matters. Synchronous speed is fine for calculating the magnetic field speed, but if you need the shaft speed, include slip.
- Mixing 50 Hz and 60 Hz: A motor designed for 50 Hz will run faster on 60 Hz (by 20%), which may cause overheating or mechanical issues unless it is rated for dual frequency.
- Assuming zero slip: Slip is never zero in an induction motor. Even at no load, there is a small slip (0.1–0.5%).
When to Use This Calculator
Use this tool when you need to:
- Estimate the speed of an existing motor from its nameplate data (poles and frequency).
- Determine the number of poles required for a target speed.
- Check if a motor will run at the right speed when connected to a different frequency supply (e.g., moving equipment from 50 Hz to 60 Hz).
- Understand the difference between synchronous and actual speed for a motor you are troubleshooting.
This calculator is for educational and planning purposes. For critical applications, always refer to the motor’s nameplate and manufacturer documentation.
Frequently Asked Questions
What is the difference between synchronous and actual speed?
Synchronous speed is the speed of the rotating magnetic field, calculated by 120×f/p. Actual speed is the rotor speed, which is always lower because of slip. For a 4-pole motor at 50 Hz, synchronous is 1500 RPM, but actual full-load might be around 1455 RPM (3% slip).
How do I find the number of poles from RPM?
Rearrange the formula: Poles = (120 × frequency) / synchronous RPM. For example, if you have a 60 Hz motor running at 1800 RPM (synchronous), poles = (120 × 60) / 1800 = 4. If you only know the actual RPM, you must estimate slip first.
Does this formula work for all AC motors?
No. It works for AC induction motors (asynchronous). Synchronous motors run at exactly synchronous speed with zero slip, so the formula gives the actual speed directly. DC motors and variable-frequency drive (VFD) applications use different relationships.
What happens if I run a 50 Hz motor on 60 Hz?
The synchronous speed increases by 20% (since 60/50 = 1.2). For example, a 4-pole motor goes from 1500 RPM to 1800 RPM. The motor may produce more power but also more heat and vibration. Unless the motor is rated for dual frequency, this can damage it.
Why do motor nameplates show speeds like 1745 RPM instead of 1800 RPM?
Because the nameplate lists the full-load speed, not the synchronous speed. The difference (55 RPM in this case) is due to slip at rated load. Slip is necessary for torque production in an induction motor.
Is slip always around 3%?
No. Slip varies with motor design and load. Typical full-load slip is 2–5% for standard motors, but small motors can have higher slip, and high-efficiency motors may have lower slip. At no load, slip is near zero.
Related
Formula used
in f | Frequency | Hz | 50 | 0 | 1000 in p | Number of poles | - | 4 | 2 | 100 in s | Slip | % | 3 | 0 | 20 out sync | Synchronous speed | RPM | (120 * f) / p | 0 out actual | Full-load speed | RPM | sync * (1 - s / 100) | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Test for Paired t Test: How to Check
- Normality Slay the Spire?