The absorbance equation is A = log10(I0/I), where I0 is the intensity of light entering a sample and I is the intensity of light exiting it. You enter the two light intensities (or the transmittance), and the calculator returns the absorbance, which is the quantity directly proportional to concentration in UV-Vis spectrophotometry.
Formula
The absorbance equation is written as:
A = log10(I0 / I)
Where:
- A = absorbance (dimensionless, often called optical density, OD)
- I0 = intensity of the incident light beam (before the sample)
- I = intensity of the transmitted light beam (after the sample)
Because the ratio I0/I has no units, absorbance itself has no units. The base-10 logarithm is used by convention; if you see ln (natural log) in a physics context, it is a different quantity called the napierian absorbance, but the standard chemistry definition uses log10.
Worked Example
Using the calculator defaults: I0 = 100 (arbitrary units) and I = 10 (same units).
Step 1: Write the ratio I0/I = 100 / 10 = 10.
Step 2: Take the base-10 logarithm: log10(10) = 1.
Step 3: The absorbance is therefore A = 1.000.
This also means the transmittance is (10/100) × 100 = 10%. An absorbance of 1 corresponds to 10% transmittance; an absorbance of 2 corresponds to 1% transmittance, and so on.
Assumptions
- The light is monochromatic (single wavelength).
- The sample is homogeneous and does not scatter light significantly.
- The detector measures only transmitted light, not reflected or fluorescent light.
- The intensity ratio is measured under identical conditions (same path length, same wavelength, same slit width).
How Absorbance Relates to Concentration: Beer-Lambert Law
The absorbance equation alone just defines the ratio of light intensities. The reason it is so useful is the Beer-Lambert law, which connects absorbance to concentration:
A = ε · c · l
Where:
- ε = molar absorptivity (L·mol−1·cm−1), a property of the molecule at a given wavelength
- c = concentration of the absorbing species (mol/L)
- l = path length of the cuvette (cm, typically 1 cm)
This is why a spectrophotometer can measure concentration: it measures A, and if you know ε and l, you can solve for c. The absorbance equation is the fundamental definition; the Beer-Lambert law is the practical application.
Transmittance vs. Absorbance
Many instruments report transmittance (%T) instead of raw intensities. The relationship is:
%T = (I / I0) × 100
So the absorbance can be calculated directly from percent transmittance:
A = log10(100 / %T) = 2 − log10(%T)
For example, if %T = 50, then A = 2 − log10(50) = 2 − 1.699 = 0.301. This is a common conversion in lab work because older instruments display %T, while quantitative analysis needs absorbance.
Common Mistakes and Misconceptions
- Using natural log instead of log10: The standard absorbance equation uses base-10. If you use ln, your value will be about 2.303 times larger.
- Forgetting that absorbance is additive: If a solution has two absorbing species, the total absorbance is the sum of each species’ absorbance, provided they do not interact.
- Assuming absorbance is linear at high concentrations: The Beer-Lambert law holds only for dilute solutions (typically A < 1.5–2). At high concentrations, molecular interactions and refractive index changes cause deviation.
- Mixing up I and I0: If you reverse them, you get a negative absorbance, which is physically meaningless for a simple measurement.
- Ignoring the blank: The I0 should be measured through a blank solution (cuvette plus solvent) to correct for reflection and solvent absorption.
How to Choose the Right Wavelength
The absorbance equation gives a value at any wavelength, but the most useful measurement is at the wavelength of maximum absorbance (λmax). At λmax, the molar absorptivity ε is highest, so the sensitivity is greatest and the calibration curve is most reliable. To find λmax, you run a spectrum (absorbance vs. wavelength) and pick the peak. For example, DNA absorbs at 260 nm, proteins at 280 nm, and many colored dyes in the visible range. Using the wrong wavelength can give a low absorbance that is hard to distinguish from noise.
Limits of the Absorbance Equation
The absorbance equation itself is exact for any ratio of intensities, but the Beer-Lambert law has practical limits:
- Deviations at high concentration: Above about 0.01 M, intermolecular interactions change ε.
- Stray light: If the instrument detects light that did not pass through the sample, the measured I is too high, and A is underestimated.
- Scattering: Turbid samples scatter light, making I too low and A too high.
- Bandwidth effects: If the monochromator passes a wide range of wavelengths, the measured absorbance is not exactly the true absorbance at the nominal wavelength.
For accurate work, keep absorbance in the range 0.1 to 1.0, where the relative error is smallest. Below 0.1, noise dominates; above 1.0, the detector may not be linear.
Frequently Asked Questions
Why is absorbance called optical density?
Optical density (OD) is an older term for the same quantity: OD = log10(I0/I). In microbiology, OD600 refers to absorbance measured at 600 nm to estimate cell density, but strictly it is absorbance, not true density.
Can absorbance be greater than 1?
Yes. An absorbance of 1 means 10% transmittance, 2 means 1%, 3 means 0.1%. There is no theoretical upper limit, but instruments become unreliable above about 2–3 because the transmitted light is too weak to measure accurately.
What is the difference between absorbance and absorptance?
Absorptance is the fraction of light absorbed, defined as (I0 − I)/I0, ranging from 0 to 1. Absorbance is the logarithm of the inverse transmittance. They are related but not equal; for example, 90% absorptance corresponds to an absorbance of 1.
How do I convert absorbance to percent transmittance?
Use the formula %T = 100 × 10−A. For A = 0.5, %T = 100 × 10−0.5 = 31.6%. This is useful when a protocol asks for transmittance but your instrument reads absorbance.
Why does the Beer-Lambert law fail at high concentration?
At high concentrations, molecules are close enough to affect each other’s electronic states, changing ε. Also, the refractive index of the solution changes, and the effective path length can differ. The law is a linear approximation valid for dilute solutions.
Does the absorbance equation depend on the solvent?
Not directly—the equation only uses light intensities. However, the solvent affects the molar absorptivity ε and the wavelength of maximum absorbance, so the same solute in different solvents will give different absorbance values at the same wavelength.
Related
Formula used
in i0 | Incident intensity I0 | - | 100 | 0 in i | Transmitted intensity I | - | 10 | 0 out a | Absorbance | - | log10(i0 / i) | 3 out t | Transmittance (I/I0) | % | (i / i0) * 100 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED