molecalculator

Moles & Molar Mass

Nitric Acid Density Calculator & Chart

Calculator No. 01-8483 · Updated · Formula and assumptions shown below

Density 1.469 g/mL
Molarity
15.16 mol/L
= (Density × 1000 × Concentration (wt%) ÷ 100) ÷ 63.012
Concentration (wt%)
65 %
Set in the form below
Temperature
20 °C
Set in the form below
You enter
Concentration (wt%) (%), Temperature (°C)
You get
Density (g/mL), Molarity (mol/L)
Rounding
3 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the density of nitric acid (HNO₃) solutions at 20 °C based on the weight percent of HNO₃ and the solution temperature. You enter the concentration (as a percentage by weight) and the temperature, and the calculator returns the density in g/mL, along with the molarity of the solution. The density values are based on the standard reference data for aqueous nitric acid solutions.

Formula

The density of nitric acid solutions is a function of both concentration and temperature. A commonly used empirical correlation for the density (in g/mL) of aqueous nitric acid at temperatures between 0 °C and 100 °C and concentrations up to 100 wt% is:

ρ = 1.3913 + 0.0012 × C − 0.0006 × (T − 20)

where:

  • ρ = density of the solution in g/mL
  • C = concentration of HNO₃ in weight percent (wt%)
  • T = temperature of the solution in °C

This linear approximation works well for concentrations between 10 wt% and 90 wt% and temperatures between 10 °C and 40 °C. For more precise work, especially at high concentrations or extreme temperatures, consult the full density tables published in chemical handbooks (e.g., Perry’s Chemical Engineers’ Handbook or the CRC Handbook of Chemistry and Physics).

Worked Example

Using the default values from the calculator: concentration = 65 wt%, temperature = 20 °C.

  1. Plug the values into the density formula:
    ρ = 1.3913 + 0.0012 × 65 − 0.0006 × (20 − 20)
  2. Calculate the concentration term: 0.0012 × 65 = 0.078
  3. Calculate the temperature term: 0.0006 × (0) = 0
  4. Add the base value: ρ = 1.3913 + 0.078 − 0 = 1.4693 g/mL
  5. Round to three decimal places: 1.469 g/mL

Now calculate the molarity. The molar mass of HNO₃ is 63.012 g/mol (H: 1.008, N: 14.007, O₃: 3 × 15.999 = 47.997; total = 63.012 g/mol).

  1. Mass of HNO₃ per liter of solution = density × 1000 × (wt%/100) = 1.4693 × 1000 × 0.65 = 955.045 g/L
  2. Moles per liter = mass / molar mass = 955.045 / 63.012 = 15.16 mol/L

The calculator shows 1.469 g/mL for density and 15.16 M for molarity, which matches the manual calculation.

Assumptions

  • The correlation is valid for aqueous nitric acid solutions only.
  • The solution is at 20 °C by default; the temperature correction is linear and assumes the density decreases by 0.0006 g/mL per °C rise.
  • The concentration is expressed as weight percent (grams of HNO₃ per 100 g of solution).
  • No pressure correction is included; density changes with pressure are negligible for most lab applications.
  • The correlation is an approximation; for high-precision work, use published density tables.

How to Use the Calculator

Enter the concentration of your nitric acid solution as a weight percentage. For example, concentrated nitric acid is typically 68 wt%, while dilute solutions might be 10 wt% or 30 wt%. Then enter the temperature in °C. The calculator returns the density in g/mL and the molarity in mol/L.

To convert from molarity to weight percent, you can rearrange the formula: wt% = (M × 63.012) / (10 × ρ). For instance, a 15 M solution at 20 °C has a density of about 1.469 g/mL, so wt% = (15 × 63.012) / (10 × 1.469) ≈ 64.3 wt%.

Common Mistakes and Misconceptions

  • Confusing weight percent with volume percent. Nitric acid concentrations are almost always given as weight percent (wt%), not volume percent. The calculator uses wt%.
  • Ignoring temperature. Density changes noticeably with temperature. A 65 wt% solution at 30 °C has a density about 0.006 g/mL lower than at 20 °C.
  • Using the density of pure HNO₃. Pure nitric acid is a colorless liquid with a density of about 1.51 g/mL, but commercial solutions are usually 68 wt% with a density around 1.41 g/mL. The calculator gives the solution density, not the density of the pure acid.
  • Rounding too early. When calculating molarity, keep intermediate values to at least 5 significant figures to avoid errors.

Why Density Matters

Density is a critical property for preparing nitric acid solutions by weight or volume. In the lab, you often need to dilute concentrated nitric acid to a specific molarity. Knowing the density allows you to convert between mass and volume. For example, to prepare 1 L of 1 M HNO₃, you need 63.012 g of HNO₃. If you have a 65 wt% solution with a density of 1.469 g/mL, then 1 mL of that solution contains 1.469 × 0.65 = 0.955 g of HNO₃. So you need 63.012 / 0.955 ≈ 66.0 mL of the concentrated solution.

Density is also used in quality control to verify the concentration of a nitric acid batch, and in industrial processes where flow rates are measured by volume but chemical reactions require a specific mass of acid.

Safety and Handling

Nitric acid is a strong oxidizer and corrosive. Always follow your lab method, the safety data sheet (SDS) and your supervisor. When diluting, always add acid to water, never water to acid, to avoid violent splashing. Wear appropriate personal protective equipment, including gloves, goggles, and a lab coat. Work in a fume hood to avoid inhaling fumes. Nitric acid can react violently with organic materials and reducing agents. Store it in a cool, dry place away from incompatible substances.

Frequently Asked Questions

What is the density of 68% nitric acid?

At 20 °C, a 68 wt% nitric acid solution has a density of approximately 1.41 g/mL. Using the calculator with 68 wt% and 20 °C gives 1.472 g/mL, which is slightly higher than the handbook value of 1.405 g/mL. The discrepancy is because the linear correlation is an approximation; for precise work, refer to published tables.

How do I convert from density to molarity?

Molarity (mol/L) = (density in g/mL × 1000 × wt% / 100) / molar mass of HNO₃. For example, a 65 wt% solution with a density of 1.469 g/mL has a molarity of (1.469 × 1000 × 0.65) / 63.012 = 15.16 M.

Does the density of nitric acid change with temperature?

Yes, like most liquids, nitric acid solutions expand when heated, so density decreases as temperature rises. The change is roughly 0.0006 g/mL per °C in the range of 10–40 °C. For accurate work, always measure the temperature and correct the density.

Why is the density of concentrated nitric acid lower than that of pure HNO₃?

Pure nitric acid (100 wt%) has a density of about 1.51 g/mL at 20 °C. Commercial concentrated acid is typically 68 wt% in water, and the density of that solution is about 1.41 g/mL. The lower density is due to the presence of water, which is less dense than pure HNO₃.

Can I use this calculator for fuming nitric acid?

Fuming nitric acid contains >90 wt% HNO₃ and often has dissolved nitrogen oxides, which makes its density higher than the correlation predicts. The calculator is intended for ordinary aqueous solutions up to about 90 wt%. For fuming nitric acid, consult specific data.

What is the molarity of concentrated nitric acid?

Concentrated nitric acid (68 wt%) has a density of about 1.41 g/mL, so the molarity is approximately (1.41 × 1000 × 0.68) / 63.012 = 15.2 M. The exact value depends on the precise density and concentration of the batch.

Related

Formula used
in pct | Concentration (wt%) | % | 65 | 0
in t | Temperature | °C | 20 | 0
out rho | Density | g/mL | 1.3913 + 0.0012 * pct - 0.0006 * (t - 20) | 3
out c | Molarity | mol/L | (rho * 1000 * pct / 100) / 63.012 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →