molecalculator

Moles & Molar Mass

Acidity Calculation by Titration: How It Works

Calculator No. 01-8436 · Updated · Formula and assumptions shown below

Acid concentration 0.1250 mol/L
Miliequivalents of acid
2.50 meq
Result, rounded to 2 decimal places
Volume of base (titrant)
25 mL
Set in the form below
Concentration of base
0.1 mol/L
Set in the form below
You enter
Volume of base (titrant) (mL), Concentration of base (mol/L), Volume of acid sample (mL), Moles of H+ per mole acid, Moles of OH- per mole base
You get
Acid concentration (mol/L), Miliequivalents of acid (meq)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Acidity calculation by titration determines the concentration of an acid in a solution by neutralizing it with a base of known concentration and measuring the volume of base required. You enter the volume and concentration of the titrant (base), the volume of the acid sample, and the stoichiometry of the reaction; the calculator returns the acid’s molarity. This page explains the titration formula, walks through a worked example, and covers the practical details you need to get accurate results.

Formula

The core relationship is that at the equivalence point, the moles of H⁺ from the acid equal the moles of OH⁻ from the base. For a monoprotic acid and a monoprotic base (like HCl and NaOH), the formula simplifies to:

M₁V₁ = M₂V₂

Where:

  • M₁ = molarity of the acid (mol/L) – what you are calculating
  • V₁ = volume of the acid sample (L)
  • M₂ = molarity of the base (mol/L) – known from preparation
  • V₂ = volume of the base used to reach the endpoint (L)

When the acid or base is polyprotic (e.g., H₂SO₄ or Ba(OH)₂), you must account for the number of ionizable protons or hydroxide ions. The general formula becomes:

ca = (cb × Vb × nb) / (Va × na)

Where:

  • ca = concentration of the acid (mol/L)
  • cb = concentration of the base (mol/L)
  • Vb = volume of base solution added (L)
  • Va = volume of acid sample (L)
  • na = number of H⁺ ions donated per acid molecule (e.g., 1 for HCl, 2 for H₂SO₄)
  • nb = number of OH⁻ ions donated per base molecule (e.g., 1 for NaOH, 2 for Ba(OH)₂)

All volumes must be in the same unit (L or mL) – the calculator converts mL to L by dividing by 1000.

Worked Example

Suppose you titrate 20.00 mL of an HCl solution with 0.1000 mol/L NaOH. It takes 25.00 mL of the NaOH to reach the endpoint. Using the default values from the calculator:

  1. Moles of NaOH used = 0.1000 mol/L × 25.00 mL / 1000 = 0.002500 mol
  2. Since nb = 1, moles of OH⁻ = 0.002500 mol
  3. At equivalence, moles of H⁺ = 0.002500 mol
  4. Since HCl provides 1 H⁺ per molecule (na = 1), moles of HCl = 0.002500 mol
  5. Concentration of HCl = 0.002500 mol / (20.00 mL / 1000) = 0.1250 mol/L

The calculator gives 0.1250 mol/L, matching the manual calculation.

Assumptions

  • The base solution is exactly the stated concentration (standardized).
  • The acid and base react completely and in the stoichiometric ratio given.
  • The endpoint detected (e.g., by color change or pH meter) corresponds exactly to the equivalence point.
  • Temperature effects on solution volume are negligible.
  • The acid is fully dissociated (strong acid) or the titration curve is interpreted correctly for weak acids.

How to Choose an Indicator

The indicator must change color at the pH of the equivalence point. For a strong acid–strong base titration, the equivalence point is at pH 7, so phenolphthalein (color change pH 8.2–10) or bromothymol blue (pH 6.0–7.6) works. For a weak acid–strong base, the equivalence point is above pH 7 (e.g., acetic acid with NaOH gives pH ~8.7 at equivalence), so phenolphthalein is suitable. For a strong acid–weak base, the equivalence point is below pH 7 (e.g., HCl with ammonia gives pH ~5.3), so methyl orange (pH 3.1–4.4) is appropriate. Using the wrong indicator can cause a systematic error of several percent.

Common Mistakes and How to Avoid Them

  • Using the wrong stoichiometric factor: For H₂SO₄, each mole gives 2 moles of H⁺. Forgetting this doubles your calculated concentration.
  • Not rinsing the burette: Residual water dilutes the titrant. Rinse the burette with the base solution before filling.
  • Reading the burette incorrectly: Read at eye level, from the bottom of the meniscus, and record to two decimal places.
  • Overshooting the endpoint: Add titrant dropwise near the endpoint. One extra drop of 0.1 mol/L NaOH is about 0.05 mL, which can cause ~0.2% error in a 25 mL titration.
  • Ignoring temperature: Burette volumes are calibrated at 20°C. At 30°C, glass expands slightly, but the effect is usually <0.1% – acceptable for most teaching labs.

Alternatives to Manual Titration

If you need higher precision or are titrating colored or turbid solutions, a pH meter with a glass electrode can be used to plot pH vs. volume of titrant. The equivalence point is the inflection point of the S-shaped curve. This method is more accurate than visual indicators, especially for weak acids or dilute solutions. Automatic titrators perform the same process with a motorized burette and software, improving reproducibility. For routine acid content in food (e.g., citric acid in juice), a simple titration with phenolphthalein is still standard.

Safety and Practical Tips

Always wear safety goggles and gloves when handling acids and bases. Concentrated acids and bases are corrosive – if you spill any, follow your lab’s emergency procedures. When preparing the base solution, use freshly boiled, deionized water to remove dissolved CO₂, which can react with the base and change its effective concentration. Standardize the base against a primary standard like potassium hydrogen phthalate (KHP) before use. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the difference between endpoint and equivalence point?

The equivalence point is the exact volume of titrant where the moles of H⁺ equal moles of OH⁻. The endpoint is the volume at which the indicator changes color. Ideally they are the same, but in practice the indicator’s transition range may not perfectly match the equivalence pH, causing a small systematic error. Choosing an indicator with a transition range that brackets the equivalence pH minimizes this.

Can I use this calculation for weak acids like acetic acid?

Yes, the calculation is the same because at the equivalence point all the weak acid has been neutralized. However, the equivalence point pH is not 7, so you must choose an indicator that changes color in the basic range (e.g., phenolphthalein). Also, the weak acid must be fully deprotonated at equivalence – which it is, because the strong base drives the reaction to completion.

Why do I need to standardize the NaOH solution?

NaOH absorbs CO₂ and water from the air, so its true concentration is lower than what you weighed. Standardization involves titrating a known mass of a primary standard (like KHP) with the NaOH to find its exact concentration. Using an unstandardized base introduces a direct error into your acid concentration result.

What if my acid is polyprotic, like phosphoric acid?

Phosphoric acid (H₃PO₄) has three ionizable protons, but they are not all neutralized at the same time. A titration with NaOH shows two distinct endpoints (the third is too weak to see). The first endpoint corresponds to na = 1, the second to na = 2. You must know which endpoint you are measuring and use the corresponding na in the formula.

How do I express acidity in terms like mg/L CaCO₃?

This is common in water chemistry. First calculate the acid concentration in mol/L, then convert to equivalents per liter (multiply by na). Then convert to mg/L CaCO₃ by multiplying by the equivalent weight of CaCO₃ (50.045 g/eq) and 1000 mg/g. For example, 0.002 mol/L HCl (n=1) gives 0.002 eq/L × 50.045 g/eq × 1000 = 100.1 mg/L as CaCO₃.

Related

Formula used
in v_b | Volume of base (titrant) | mL | 25.00 | 0
in c_b | Concentration of base | mol/L | 0.1000 | 0
in v_a | Volume of acid sample | mL | 20.00 | 0.001
in n_a | Moles of H+ per mole acid | - | 1 | 1
in n_b | Moles of OH- per mole base | - | 1 | 1
out c_a | Acid concentration | mol/L | (c_b * v_b / 1000 * n_b) / (v_a / 1000 * n_a) | 4
out meq | Miliequivalents of acid | meq | c_a * (v_a / 1000) * n_a * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →