molecalculator

Moles & Molar Mass

Normality of K2Cr2O7 Solution: How to Calculate

Calculator No. 01-7716 · Updated · Formula and assumptions shown below

Molarity 0.0397 mol/L
Normality (redox, Cr3+)
0.2384 eq/L
= Molarity × 6
Mass of K2Cr2O7
2.922 g
Set in the form below
Molar mass of K2Cr2O7
294.185 g/mol
Set in the form below
You enter
Mass of K2Cr2O7 (g), Molar mass of K2Cr2O7 (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Normality (redox, Cr3+) (eq/L)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The normality of a K2Cr2O7 solution depends on the reaction it is used for: in the common redox titration (dichromate being reduced to Cr3+), 1.0 M K2Cr2O7 equals 6.0 N. To find the normality of a specific solution, multiply its molarity by 6 (the number of electrons gained per dichromate ion in that reduction).

Formula

Normality (N) is defined as the number of equivalents of solute per liter of solution. For a redox reaction, one equivalent is the amount of substance that gains or loses one mole of electrons. The formula used here is:

N = M × n

where:

  • N = normality (equivalents per liter, eq/L)
  • M = molarity (moles per liter, mol/L)
  • n = number of electrons transferred per formula unit of the solute (for K2Cr2O7 in acidic reduction to Cr3+, n = 6)

Molarity itself is calculated from the mass of solute, its molar mass, and the final volume of solution:

M = m / (Mm × VL)

where m is mass in grams, Mm is molar mass in g/mol (294.185 g/mol for K2Cr2O7), and VL is volume in liters (mL ÷ 1000).

Worked Example

Using the default values from the calculator: 2.922 g of K2Cr2O7 (molar mass 294.185 g/mol) dissolved to a final volume of 250 mL.

  1. Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
  2. Calculate moles of K2Cr2O7: 2.922 g ÷ 294.185 g/mol = 0.009933 mol
  3. Calculate molarity: 0.009933 mol ÷ 0.250 L = 0.03973 mol/L (0.0397 M)
  4. Calculate normality: 0.03973 M × 6 = 0.2384 eq/L (0.2384 N)

The calculator gives the same result: molarity 0.0397 M, normality 0.2384 N.

Assumptions

  • The dichromate ion is completely reduced to Cr3+ in acidic solution (the standard redox titration condition).
  • The K2Cr2O7 is pure and anhydrous.
  • The final volume is used (not the volume of solvent added).
  • The solution is at typical laboratory temperature (density changes are negligible).

Why 6 Equivalents per Mole?

Potassium dichromate (K2Cr2O7) contains two chromium atoms, each in the +6 oxidation state. In acidic solution, the dichromate ion is reduced to two Cr3+ ions:

Cr2O72− + 14H+ + 6e− → 2Cr3+ + 7H2O

Each chromium atom gains 3 electrons (from +6 to +3), so the two chromium atoms together gain 6 electrons. Therefore, one mole of K2Cr2O7 accepts 6 moles of electrons, giving an n-factor of 6. This is the basis for the 1 M = 6 N conversion in redox titrations.

It is crucial to note that normality is reaction-specific. If K2Cr2O7 were used in a different reaction (for example, as an oxidizing agent in a non-redox context, which is rare), the n-factor could be different. But in virtually all analytical applications—such as the titration of iron(II) or the determination of chemical oxygen demand—the reduction to Cr3+ is what matters, so n = 6.

How to Prepare a Normal K2Cr2O7 Solution

To prepare a solution of a specific normality, you need to weigh the correct mass of K2Cr2O7 and dissolve it in a final volume of solution. The required mass is:

m (g) = N × V (L) × (Mm / n)

For example, to make 500 mL of 0.1 N K2Cr2O7:

  • Equivalent mass = 294.185 g/mol ÷ 6 = 49.0308 g/eq
  • Mass needed = 0.1 eq/L × 0.500 L × 49.0308 g/eq = 2.4515 g

Weigh 2.4515 g of dry K2Cr2O7, dissolve in distilled water, and dilute to exactly 500 mL in a volumetric flask.

K2Cr2O7 is a primary standard, meaning it can be weighed accurately and used directly to make a standard solution because it is available in high purity, is stable, and does not absorb moisture. This is an advantage over, say, KMnO4, which must be standardized against a primary standard.

Common Mistakes and Misconceptions

  • Using n = 6 for all contexts: As noted, normality depends on the reaction. In some older texts, you might see n = 3 for dichromate (based on one chromium atom), but that is incorrect for the full dichromate ion. Always use the balanced half-reaction.
  • Confusing molarity and normality: A 1 N K2Cr2O7 solution is not 1 M; it is 1/6 M (approximately 0.1667 M). If you mistakenly use molarity when you need normality, your titration calculations will be off by a factor of 6.
  • Volume of solvent vs. final volume: Always dilute to the final volume in a volumetric flask. Adding 500 mL of water to 2.45 g of solute does not give exactly 500 mL of solution.
  • Ignoring acidity: The reduction of dichromate to Cr3+ requires acidic conditions. If the solution is not sufficiently acidic, the reaction may not proceed as expected, and the effective n-factor could change (though in practice, titrations are done with excess acid).

Applications of K2Cr2O7 Normality

Knowing the normality of a K2Cr2O7 solution is essential in several quantitative analyses:

  • Iron titration: Determination of Fe2+ in ores or solutions. The reaction is 6Fe2+ + Cr2O72− + 14H+ → 6Fe3+ + 2Cr3+ + 7H2O. At the equivalence point, milliequivalents of Fe2+ = milliequivalents of dichromate.
  • Chemical Oxygen Demand (COD): In environmental testing, dichromate is used to oxidize organic matter in water samples. The amount of dichromate consumed is measured, and the normality is used to calculate the oxygen equivalent.
  • Standardization of other solutions: Because it is a primary standard, K2Cr2O7 can be used to standardize sodium thiosulfate (indirectly, via iodine) or other reducing agents.

Safety and Handling

Potassium dichromate is a strong oxidizer and a known carcinogen (hexavalent chromium). It is harmful if inhaled, swallowed, or absorbed through the skin. Always wear appropriate personal protective equipment (gloves, safety glasses, lab coat) and work in a fume hood if preparing solutions. Avoid contact with combustible materials, as dichromate can cause fires. Dispose of waste according to local regulations for chromium(VI) waste. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

Q: What is the normality of 0.1 M K2Cr2O7?
A: In acidic redox reactions, 0.1 M K2Cr2O7 is 0.6 N (0.1 × 6).

Q: How do I convert normality to molarity for K2Cr2O7?
A: Divide normality by 6: M = N / 6. For example, 0.5 N is 0.0833 M.

Q: Can I use K2Cr2O7 as a primary standard for preparing a normal solution?
A: Yes, K2Cr2O7 is a primary standard because it is available in high purity, is non-hygroscopic, and has a high molar mass, which reduces weighing errors.

Q: Why is the n-factor 6 and not 3?
A: The dichromate ion contains two chromium atoms, each changing from +6 to +3, so each ion gains 6 electrons total. The n-factor is per mole of K2Cr2O7, not per chromium atom.

Q: Does temperature affect the normality?
A: Normality is based on moles and volume; volume changes slightly with temperature, so at extreme temperatures the concentration can shift. For routine lab work at room temperature, the effect is negligible.

Q: What if I use K2Cr2O7 in a non-redox reaction?
A: Normality is only meaningful for the specific reaction. If dichromate is used in a precipitation or complexation reaction (rare), the equivalent weight would be different. Always define the reaction when stating normality.

Related

Formula used
in m | Mass of K2Cr2O7 | g | 2.922 | 0
in mm | Molar mass of K2Cr2O7 | g/mol | 294.185 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out n | Normality (redox, Cr3+) | eq/L | c * 6 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →