An enthalpy of formation table lists the standard molar enthalpy of formation (ΔHf°) for common compounds, typically in kJ/mol at 25 °C and 1 atm. You use it to calculate the heat of a reaction by subtracting the sum of the reactants’ formation enthalpies from the sum of the products’ formation enthalpies. The values are defined relative to elements in their most stable form, which are assigned a ΔHf° of exactly zero.
Formula
The standard enthalpy of reaction (ΔHrxn°) is calculated from formation enthalpies using Hess’s law:
ΔHrxn° = Σ [nproducts × ΔHf°(products)] − Σ [nreactants × ΔHf°(reactants)]
where:
- n = stoichiometric coefficient (dimensionless, from the balanced equation)
- ΔHf° = standard molar enthalpy of formation (kJ/mol)
- Σ = sum over all products or all reactants
Each ΔHf° is the enthalpy change when one mole of the compound forms from its elements in their standard states at 298.15 K (25 °C) and 1 bar (or 1 atm, depending on the table). For elements like O2(g), C(s, graphite), and H2(g), the value is 0 kJ/mol by definition.
Worked Example
Calculate the standard enthalpy of combustion of methane: CH4(g) + 2 O2(g) → CO2(g) + 2 H2O(l)
From a standard table (all values in kJ/mol):
- ΔHf°(CH4) = −74.87
- ΔHf°(O2) = 0
- ΔHf°(CO2) = −393.51
- ΔHf°(H2O(l)) = −285.83
Products: 1 × (−393.51) + 2 × (−285.83) = −393.51 − 571.66 = −965.17 kJ
Reactants: 1 × (−74.87) + 2 × 0 = −74.87 kJ
ΔHrxn° = −965.17 − (−74.87) = −890.30 kJ/mol
The combustion of one mole of methane releases 890.30 kJ of heat, which matches the accepted value of −890.4 kJ/mol within rounding.
Assumptions
- All substances are in their standard states at 298.15 K (25 °C) and 1 bar.
- Water is in the liquid state unless the table explicitly says H2O(g); the gas-phase value (−241.83 kJ/mol) differs by the enthalpy of vaporization (44.0 kJ/mol).
- The balanced equation uses the same physical states as the table entries.
- Formation enthalpies are independent of pressure for ideal gases; for condensed phases the correction is negligible.
Where to Find Reliable Tables
The most commonly cited source is the NIST Chemistry WebBook, which compiles data from the National Bureau of Standards (now NIST) and peer-reviewed literature. Other standard references include the CRC Handbook of Chemistry and Physics and the Lange’s Handbook of Chemistry. Most general chemistry textbooks include an appendix table covering 50–100 common substances—enough for typical homework and lab calculations. For industrial or research work, you may need the more comprehensive JANAF Thermochemical Tables, which cover thousands of species across a range of temperatures, not just 25 °C.
When you look up a value, check three things: the physical state (s, l, g, aq), the reference state of the elements (usually graphite for carbon, not diamond), and whether the table uses 1 bar or 1 atm as standard pressure. The difference between the two is small (about 0.1 kJ/mol for gases) but can matter in precise work.
Common Mistakes and Misconceptions
The most frequent error is forgetting to multiply each ΔHf° by its stoichiometric coefficient. Another is using the wrong physical state—for example, using H2O(g) when the reaction produces liquid water, which shifts the answer by 44 kJ per mole of water. A third mistake is treating the formation enthalpy of a compound as if it were the enthalpy of its decomposition; the sign is simply reversed, but only if the decomposition goes to the elements in their standard states.
Many students assume that all exothermic reactions have negative ΔHf° values, but that is not true. For example, NO(g) has a positive ΔHf° of +90.25 kJ/mol because forming it from N2 and O2 requires energy input. Similarly, ozone (O3) has a positive formation enthalpy (+142.7 kJ/mol) because it is less stable than O2. A positive formation enthalpy means the compound is less stable than its elements; a very negative one (like CO2 at −393.5 kJ/mol) means it is very stable.
Another misconception is that the table gives the “energy content” of a fuel. It does not. The formation enthalpy of a fuel like octane (−249.9 kJ/mol) tells you how much heat is released when it forms from elements, not how much energy is released when it burns. To get the combustion energy, you must run the full Hess’s law calculation with the products (CO2 and H2O).
How to Choose the Right Value
When a compound exists in multiple forms, pick the one that matches your reaction conditions:
- For water, decide between liquid (−285.83 kJ/mol) and gas (−241.83 kJ/mol). If the reaction is at 25 °C and water condenses, use liquid; if it stays as steam, use gas.
- For carbon, use graphite (0 kJ/mol) unless the reaction explicitly involves diamond (+1.90 kJ/mol) or amorphous carbon.
- For ions in aqueous solution, the convention sets H+(aq) to 0 kJ/mol, and all other ions are measured relative to that. This lets you calculate heats of reaction for acid–base and precipitation reactions.
- For organic compounds, check whether the table lists the value for the solid, liquid, or gas phase. Many tables list only one phase; if you need another, you must add or subtract the enthalpy of fusion or vaporization.
If your reaction is not at 25 °C, you cannot simply use the table value. You must apply Kirchhoff’s law, which adds a correction term ∫ΔCp dT to account for the heat capacity difference between products and reactants over the temperature range.
Limits of the Table
Formation enthalpy tables are only valid for the standard state, which means pure substances at 1 bar. Real solutions, mixtures, and high-pressure gases deviate from these ideal values. For dilute aqueous solutions, the error is usually small, but for concentrated solutions or non-ideal mixtures, you need activity-corrected data. The table also says nothing about kinetics—a reaction with a very negative ΔHrxn° might still be extremely slow without a catalyst. Thermodynamics tells you whether a reaction can happen; it does not tell you how fast.
For reactions involving ions, the formation enthalpies of aqueous ions are defined with the convention that ΔHf°(H+, aq) = 0. This is arbitrary but consistent, so you can use it to calculate heats of neutralization, dissolution, and precipitation. However, you cannot compare an ion’s formation enthalpy to a neutral molecule’s directly, because the ion values include the hydration energy relative to the proton convention.
Frequently Asked Questions
What is the difference between enthalpy of formation and enthalpy of combustion?
Enthalpy of formation is the heat change when one mole of a compound forms from its elements in their standard states. Enthalpy of combustion is the heat released when one mole of a substance burns completely in oxygen. Combustion enthalpies are always negative (exothermic) for fuels, while formation enthalpies can be positive or negative. You can calculate a combustion enthalpy from formation enthalpies using Hess’s law, as shown in the worked example above.
Why is the enthalpy of formation of an element zero?
By convention, the standard enthalpy of formation of an element in its most stable form is defined as zero. This gives a consistent reference point for all compounds. For example, O2(g) is zero, but O3(g) is +142.7 kJ/mol because ozone is not the most stable form of oxygen. The choice is arbitrary but universal, so all tables agree on the zero points.
Can I use a formation enthalpy table for reactions at temperatures other than 25 °C?
Not directly. The table values are for 298.15 K only. To find ΔH at another temperature, you must use Kirchhoff’s law: ΔH(T2) = ΔH(T1) + ∫T1T2 ΔCp dT, where ΔCp is the difference in heat capacities between products and reactants. For small temperature differences (a few tens of degrees), the correction is often small, but for high-temperature processes like combustion in engines, it is significant.
What does a positive enthalpy of formation mean physically?
A positive ΔHf° means that forming the compound from its elements absorbs heat—the compound is less stable than its constituent elements. Such compounds are called endothermic compounds. Examples include nitric oxide (+90.25 kJ/mol) and acetylene (+226.7 kJ/mol). Acetylene’s positive value is why it releases a large amount of heat when it burns; the products (CO2 and H2O) are much more negative, so the difference is large.
How do I handle hydrates or compounds with water of crystallization?
Hydrates have their own formation enthalpy values that include the water molecules. For example, CuSO4·5H2O(s) has a different ΔHf° than anhydrous CuSO4(s). You must use the value that matches the exact formula in your balanced equation. If your table lacks the hydrate, you can calculate it by adding the formation enthalpy of the anhydrous salt plus the formation enthalpy of the appropriate number of water molecules, but this ignores the hydration energy, so it is only an approximation.
Why do different tables show slightly different values?
The values come from experimental measurements, and different sources may use different reference states, temperature calibrations, or data sets. The NIST WebBook and the CRC Handbook usually agree to within a few tenths of a kJ/mol for well-studied compounds. For less common compounds, the uncertainty can be several kJ/mol. Always cite the source you used and note the standard pressure (1 bar vs. 1 atm) so your calculation is reproducible.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check