molecalculator

Moles & Molar Mass

PCB Thickness Calculator: Convert Layers to Millimeters

Calculator No. 01-3083 · Updated · Formula and assumptions shown below

Estimated PCB thickness 1.600 mm
Estimated PCB thickness
0.0630 in
Result, rounded to 4 decimal places
Copper layer count
2 layers
Set in the form below
Copper thickness per layer
0.035 mm
Set in the form below
You enter
Copper layer count (layers), Copper thickness per layer (mm), Dielectric thickness between copper layers (mm)
You get
Estimated PCB thickness (mm), Estimated PCB thickness (in)
Rounding
3 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A PCB thickness calculator estimates a printed circuit board’s finished thickness from its layer stack, or converts a known thickness between millimeters and inches. Entering the board’s actual layer and material dimensions gives a useful estimate; a layer count alone cannot determine thickness because copper, dielectric spacing, and fabrication choices vary.

Formula

This calculator estimates total thickness as the sum of the copper thicknesses and the dielectric gaps between adjacent copper layers:

t = (c × n) + (d × (n − 1))

  • t is estimated finished board thickness in millimeters (mm).
  • n is the number of copper layers.
  • c is the average copper thickness per layer in mm.
  • d is the dielectric thickness between adjacent copper layers in mm.

The inch output is t ÷ 25.4, using the exact conversion 25.4 mm per inch. The formula is a simplified stack-up model, not a universal manufacturing rule. It treats all copper layers as equally thick and all dielectric gaps as equal. In a real multilayer construction, core and prepreg sections can have different thicknesses, and the final pressed stack depends on the specified materials and fabrication process.

Worked Example

Using the calculator’s default values: two copper layers, 0.035 mm copper per layer, and a 1.53 mm dielectric gap:

  1. Copper contribution: 0.035 mm × 2 = 0.07000 mm.
  2. There is one gap between two layers: 1.53 mm × (2 − 1) = 1.53000 mm.
  3. Total: 0.07000 mm + 1.53000 mm = 1.600 mm.
  4. In inches: 1.600 mm ÷ 25.4 = 0.062992 in, or 0.0630 in to four decimal places.

The result is an estimate for the simplified stack represented by the inputs. It is not a claim that every two-layer board is 1.6 mm thick.

What PCB Thickness Means

PCB thickness usually means the overall thickness of the finished bare board, measured from one outside surface to the other. It is distinct from copper weight, copper thickness, dielectric thickness, and the thickness of an assembled board with components or solder added. When a drawing or order specification gives a thickness, check whether it means the finished board and whether a tolerance is stated.

Common nominal board thicknesses include 0.8 mm, 1.0 mm, 1.6 mm, and 2.0 mm. These are common design choices, not a complete list or a guarantee that a fabricator can supply every value for every construction. The actual acceptable range is defined by the drawing, manufacturing capability, and any applicable procurement specification.

Layer count does not directly tell you the thickness. A two-layer board may be thin or thick, while a multilayer board can use thinner dielectric sections to keep its overall thickness near a chosen target. The board’s materials and stack-up determine the result.

How to Use the Estimate

For a quick estimate, enter the number of copper layers, the thickness of one copper layer, and an average dielectric gap. The default copper input of 0.035 mm is 35 micrometers, a representative value often associated with 1 oz/ft² nominal copper foil before processing. Finished outer copper can differ from the starting foil because manufacturing may add copper during plating; the nominal foil designation should not be mistaken for a guaranteed finished copper thickness.

The dielectric input needs particular care. In a two-layer board it represents the insulation separating the two copper layers. For a board with more layers, it represents an average gap in this simplified calculation. If you know the stack-up, use its actual section thicknesses rather than assuming identical gaps. For a precise total, add the thickness of every copper and insulating section specified in the stack-up, including any outside coatings only if the required measurement includes them.

  • Use the same units for copper and dielectric inputs; this calculator expects millimeters.
  • Count copper layers, not component sides or signal traces.
  • For a custom design, use the fabricator’s proposed stack-up and finished-thickness tolerance.
  • For a known board thickness, the calculator’s inch output is a conversion, not an independent measurement.

Choosing Thickness and Understanding Tolerances

Thickness affects mechanical fit and may affect stiffness, connector engagement, enclosure clearances, and the board’s electrical geometry. A thicker board is generally more rigid for the same material and dimensions, but stiffness also depends on board size, shape, material, copper distribution, and support. For controlled-impedance designs, dielectric thickness and material properties matter; overall thickness alone is not enough to determine impedance.

Choose a target based on the assembly and mechanical drawing, then confirm that the proposed construction is available. A nominal value is not an exact measurement: fabrication tolerances allow the delivered board to fall within a stated range. Do not design a tight slot, edge connector, or enclosure fit around the nominal value without accounting for that tolerance. Ask for the finished thickness definition and tolerance when these details affect fit.

Costs cannot be calculated from thickness alone. Material selection, layer count, board dimensions, copper requirements, finish, tolerances, and production details all influence a quote. A special thickness or unusually tight tolerance may constrain manufacturing options, so get confirmation for the complete specification rather than treating a calculator result as a price or fabrication guarantee.

Common Misconceptions and Limits

A frequent mistake is to multiply the number of layers by copper thickness and call that the board thickness. That omits the insulating material, which commonly accounts for most of a board’s thickness. Another mistake is to multiply the dielectric gap by the layer count: for n layers there are n − 1 spaces between adjacent layers, as represented in this simplified model.

Real stack-ups are often asymmetric, use different copper thicknesses on different layers, or contain multiple dielectric materials. Copper is also not necessarily a uniform full-sheet thickness after patterning and processing. Consequently, this calculator is appropriate for a rough estimate or a simple symmetric construction, not a substitute for a manufacturer’s stack-up drawing, inspection, or finished-board specification. If the thickness is critical, obtain the construction and tolerance from the fabricator and verify the delivered board against the required specification.

Frequently Asked Questions

What is the standard PCB thickness?
There is no single standard thickness for all PCBs. Values such as 1.6 mm are common, but the right nominal thickness depends on the design, enclosure, connector, layer stack, and manufacturer’s available constructions.

How thick is a 2-layer PCB?
A two-layer PCB can be made to different thicknesses. Its total thickness is approximately the two copper layers plus the dielectric separating them, along with any included surface layers or coatings. Use a specified stack-up rather than layer count alone for an accurate value.

How many inches is 1.6 mm?
1.6 mm ÷ 25.4 = about 0.0630 inches. This is a unit conversion; it does not account for manufacturing tolerance.

Does copper weight determine PCB thickness?
No. Copper weight is a measure associated with copper thickness, not total board thickness. The dielectric and other stack-up layers also contribute, and finished copper can differ from nominal starting foil.

Is this calculator accurate enough for a PCB order?
It is useful for estimating a simple stack, but an order should state the required finished thickness and tolerance. For multilayer or tightly controlled designs, rely on the fabricator’s confirmed stack-up and specification.

Related

Formula used
in cu | Copper layer count | layers | 2 | 1
in ct | Copper thickness per layer | mm | 0.035 | 0
in dt | Dielectric thickness between copper layers | mm | 1.53 | 0
out t | Estimated PCB thickness | mm | ct * cu + dt * (cu - 1) | 3
out tin | Estimated PCB thickness | in | (ct * cu + dt * (cu - 1)) / 25.4 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →