molecalculator

Moles & Molar Mass

PCB Thermal Conductivity Calculator: How to Use It

Calculator No. 01-10359 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A PCB thermal conductivity calculator estimates how quickly heat moves through a printed circuit board’s material, typically giving you a thermal conductivity value in W/m·K or a thermal resistance in °C/W. You enter the board material (or its conductivity), the thickness of the copper and dielectric layers, and the trace dimensions, and the calculator returns the effective thermal conductivity or the temperature rise for a given power. This helps you predict whether a board will overheat before you build it.

Formula

The calculator uses the series thermal resistance model for a board with a copper layer on top of a dielectric substrate. The effective thermal conductivity is a thickness-weighted average:

k_eff = (k_copper × t_copper + k_substrate × t_substrate) / (t_copper + t_substrate)

  • k_eff = effective thermal conductivity (W/m·K)
  • k_copper = thermal conductivity of copper (385 W/m·K)
  • t_copper = copper thickness (m, converted from oz/ft²: 1 oz = 35 µm)
  • k_substrate = thermal conductivity of the dielectric (FR-4: 0.25 W/m·K, aluminum: 150 W/m·K, etc.)
  • t_substrate = thickness of the dielectric (m)

For a simple trace, the temperature rise is approximated by Fourier’s law: ΔT = P × L / (k_eff × A), where A is the cross-sectional area (width × thickness) of the trace.

Worked Example

Using the default values: FR-4 board (k = 0.25 W/m·K), total thickness 1.6 mm, 1 oz copper (35 µm), trace width 2 mm, trace length 50 mm, power 1 W.

  1. Convert copper thickness: 1 oz = 35 µm = 0.035 mm
  2. Substrate thickness = 1.6 mm – 0.035 mm = 1.565 mm
  3. Compute effective k: (385 × 0.035 + 0.25 × 1.565) / 1.6 = (13.475 + 0.391) / 1.6 = 13.866 / 1.6 = 8.666 W/m·K
  4. Trace cross-section area = 2 mm × 0.035 mm = 0.07 mm² = 7e-8 m²
  5. ΔT = 1 W × 0.05 m / (8.666 × 7e-8) = 0.05 / 6.066e-7 = 82,430 °C

That result is absurdly high because the model assumes heat flows only along the trace with no spreading into the board. Real boards spread heat laterally, so the actual temperature rise is far lower. This example shows why you need a proper thermal simulation for real designs.

Assumptions

  • Heat flows in one direction (along the trace or through the thickness).
  • Materials are homogeneous and isotropic (FR-4 is actually anisotropic).
  • No convection or radiation losses; only conduction.
  • Copper thickness is uniform; 1 oz = 35 µm is a standard approximation.
  • Board is at steady state, not transient.

Why Thermal Conductivity Matters in PCBs

Every component on a PCB generates heat, and that heat must go somewhere. If it doesn’t spread or dissipate, hotspots form, reducing component lifespan and causing solder joint failures. Thermal conductivity (k) measures how well a material conducts heat; higher k means faster heat spreading. Copper (385 W/m·K) is an excellent conductor, but the dielectric substrate (FR-4, ~0.25 W/m·K) is a good insulator. The effective conductivity of a board is a mix of both, heavily weighted by thickness. For high-power LEDs, motor drivers, or RF amplifiers, designers often use aluminum-backed PCBs (metal-core PCBs, MCPCB) where the dielectric is thin and the aluminum base spreads heat efficiently.

How to Choose the Right Thermal Conductivity Value

When you look up a material’s thermal conductivity, you’ll see values like 0.25 W/m·K for standard FR-4, but that’s for the bulk resin-glass composite. In reality, FR-4’s conductivity varies with temperature and resin content. For design, use the manufacturer’s datasheet value, not a generic number. For aluminum substrates, the dielectric layer (often a thermally conductive prepreg) has a k between 1 and 3 W/m·K, which dominates the thermal path. In the calculator, if you select Aluminum (150 W/m·K) but the dielectric is 100 µm thick with k=2, the effective k will be much lower than 150. Always model the actual stack-up: copper foil, dielectric, and base metal.

Common Mistakes and Misconceptions

  • Using bulk copper conductivity for traces: Traces are thin and narrow; their thermal resistance is high. You must use the cross-section area, not just the width.
  • Ignoring the dielectric layer: The dielectric is the bottleneck. Even a thin layer with low k can dominate the thermal resistance.
  • Confusing thermal conductivity with thermal resistance: Conductivity (W/m·K) is a material property; resistance (°C/W) depends on geometry. A thick board can have the same k but higher resistance.
  • Assuming 1 oz copper is 35 µm exactly: It’s a nominal value; actual thickness may be 30–40 µm. For precise work, measure it.
  • Forgetting that heat spreads in 2D/3D: The simple 1D model here underestimates spreading, so real temperature rises are lower.

Alternatives to Simple Calculators

For real PCB design, you’ll want more than a one-dimensional calculator. Options include:

  • Finite element analysis (FEA) software: Tools like ANSYS Icepak or COMSOL simulate heat flow in 3D, including convection and radiation.
  • Thermal simulation in EDA tools: Some PCB design suites (e.g., Altium, KiCad with plugins) offer thermal analysis.
  • Thermal resistance networks: More detailed models break the board into nodes and compute a network of resistances.
  • Thermal imaging: After building a prototype, use an IR camera to measure actual temperatures.

For quick estimates, this calculator gives a rough idea, but always validate with a simulation or measurement for critical designs.

Frequently Asked Questions

What is the thermal conductivity of FR-4?

Standard FR-4 has a thermal conductivity of about 0.25 W/m·K in the plane of the board (X-Y) and slightly higher (0.3–0.4) through the thickness, but most datasheets quote 0.25. It’s a poor conductor, which is why high-power boards use metal cores.

How do I convert copper thickness from oz to mm?

1 oz/ft² copper is the weight per square foot, and it corresponds to a thickness of 35 µm (0.035 mm). For 2 oz, it’s 70 µm; for 0.5 oz, 17.5 µm. This is a standard industry conversion.

Why does my PCB get hot even with thick copper?

Thick copper helps spread heat laterally, but the bottleneck is often the dielectric layer between the copper and the heatsink. If the dielectric has low k, heat can’t get to the metal base. Also, components with small footprints create local hotspots that copper alone can’t eliminate.

Can I use this calculator for aluminum-core PCBs?

Yes, but you must enter the correct stack-up: the aluminum base has a high k (150–200 W/m·K), but the dielectric layer (typically 50–150 µm) has a k of 1–3 W/m·K. The calculator’s effective k will be dominated by that dielectric, which is realistic.

What is a good thermal conductivity for a PCB material?

It depends on the application. For standard digital boards, 0.25 W/m·K is fine. For high-power LED boards, you want materials with k > 1 W/m·K, such as aluminum-backed laminates or ceramic-filled PTFE (e.g., Rogers 4350B has ~0.6 W/m·K). For extreme thermal performance, ceramic substrates (AlN, k=170) are used.

Does the calculator account for vias and thermal pads?

No, it only models a simple trace or a uniform board. Vias (copper-plated holes) can significantly improve heat transfer from the top layer to inner layers or the backside. For designs with vias, you need a more detailed model that includes their thermal resistance.

Related

Formula used
in sel | Board material | FR-4=0.25, Aluminum=150, Copper=385, Polyimide=0.12, Ceramic (Al2O3)=25
in mm | Board thickness | mm | 1.6 | 0.1
in mm | Copper thickness (oz) | oz | 1 | 0.5
in mm | Trace width | mm | 2 | 0.1
in mm | Trace length | mm | 50 | 1
in w | Power dissipated | W | 1 | 0.001
out k_eff | Effective thermal conductivity (W/m·K) | W/m·K | (sel * (t_copper / 1000) + 0.25 * ((t_board - t_copper) / 1000)) / (t_board / 1000) | 3
out dT | Temperature rise (°C) | °C | w * (t_trace / 1000) / (k_eff * (t_trace / 1000) * (t_trace / 1000)) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →