Use the pH and pOH equations to describe how acidic or basic a dilute aqueous solution is: pH = −log₁₀[H₃O⁺] and pOH = −log₁₀[OH⁻], with concentrations expressed in mol/L. At 25 °C, pH + pOH = 14.00; enter either ion concentration or one of these values to calculate the others.
Formula
The equations are pH = −log₁₀[H₃O⁺] and pOH = −log₁₀[OH⁻]. Here [H₃O⁺] is hydronium-ion concentration in mol/L, and [OH⁻] is hydroxide-ion concentration in mol/L. The calculator’s first output is pH from the entered hydronium concentration; its second is pOH from the entered hydroxide concentration. The input values must be positive: a zero concentration cannot be used inside a logarithm.
Water also obeys the ion-product relation Kw = [H₃O⁺][OH⁻] in dilute aqueous solutions. Taking the negative base-10 logarithm gives pH + pOH = pKw, where pKw = −log₁₀Kw. At 25 °C, pKw is approximately 14.00, so pOH = 14.00 − pH and pH = 14.00 − pOH. The relationship depends on temperature; 14.00 is not an exact universal constant.
The calculator reports the two direct concentration-based logarithms. Its temperature field is included to highlight that temperature changes water’s ion product; it does not apply a temperature correction to the direct pH and pOH calculations. The displayed water ion-product output is 14.00 as a reference value. Do not use that output as a temperature-dependent prediction.
Worked Example
Using the default inputs, [H₃O⁺] = 0.00001 mol/L, [OH⁻] = 0.000001 mol/L, and temperature = 25 °C:
- pH = −log₁₀(0.00001) = 5.00.
- pOH = −log₁₀(0.000001) = 6.00.
- At 25 °C, pH + pOH = 5.00 + 6.00 = 11.00, not 14.00; therefore these two independently entered concentrations are not a mutually consistent equilibrium pair for pure water conditions.
This distinction matters: the two direct outputs are each calculated from their own input. The calculator does not assume the hydronium and hydroxide concentrations describe the same valid solution. For a consistent pair at 25 °C, their product should be approximately 1.0 × 10⁻¹⁴ (mol/L)². For example, pH 5.00 implies pOH 9.00 and [OH⁻] = 1.0 × 10⁻⁹ mol/L under the 25 °C relation.
Assumptions
- The logarithm inputs are positive concentrations in mol/L, not masses, volumes, or unconverted values in mmol/L.
- The pH + pOH = 14.00 shortcut applies approximately to dilute aqueous solutions at 25 °C.
- Concentration-based equations are used as a practical approximation; rigorous pH is defined using hydrogen-ion activity.
- The temperature input does not change the direct pH or pOH results and is not used to calculate a temperature-specific pKw.
What pH and pOH Mean
pH and pOH are logarithmic scales. A one-unit change corresponds to a tenfold change in the relevant ion concentration. At 25 °C, pH below 7 is conventionally acidic, pH 7 is neutral, and pH above 7 is basic. Neutrality means hydronium and hydroxide activities are equal; the neutral pH shifts with temperature because Kw changes.
The letter p in pH is conventionally associated with taking the negative base-10 logarithm. Thus, a lower pH means greater hydronium activity, while a lower pOH means greater hydroxide activity. Neither scale is a direct measure of how much acid or base is present in total: a weak acid and a strong acid can produce different pH values at the same analytical concentration.
How to Use the Equations
First identify what information is available, then use the matching equation:
- For a known hydronium concentration, calculate pH = −log₁₀[H₃O⁺].
- For a known hydroxide concentration, calculate pOH = −log₁₀[OH⁻].
- At 25 °C, convert between pH and pOH using pH + pOH = 14.00.
- If a concentration is given in mmol/L, divide it by 1000 before applying the logarithm. For example, 0.10 mmol/L is 0.00010 mol/L, giving pH 4.00 if that is the hydronium concentration.
When starting with a measured pH, the corresponding concentration estimate is [H₃O⁺] = 10−pH mol/L. Similarly, [OH⁻] = 10−pOH mol/L. At 25 °C, a measured pH of 3.00 corresponds to pOH 11.00 and an estimated hydroxide concentration of 1.0 × 10⁻¹¹ mol/L.
Limits, Measurements, and Common Errors
Strictly, pH is defined as −log₁₀aH, where aH is hydrogen-ion activity, a dimensionless effective quantity relative to a standard state. Using concentration in mol/L is a useful dilute-solution approximation. In concentrated solutions, ionic interactions make activity differ from concentration, so a simple concentration calculation may not match a measured pH.
- Using zero or a negative concentration: neither can be inserted into a logarithm. A computed pH also has no practical meaning if the concentration is below the method’s detection limit.
- Mixing units: the logarithm must use mol/L for this calculator. Convert mmol/L, μmol/L, or other units first.
- Assuming pH + pOH is always 14: that is an approximate 25 °C relationship, not a rule for all temperatures or concentrated mixtures.
- Expecting the inputs to agree automatically: separately entered hydronium and hydroxide concentrations can produce pH and pOH values that do not satisfy Kw.
- Over-rounding: retain sensible precision through calculations. A pH change of 0.01 represents a concentration factor of about 1.023, so rounding can matter in precise comparisons.
A meter reading is the practical check when an actual solution’s pH matters: temperature and ionic strength shift pH, and the meter must be suitable and properly calibrated for the measurement. A calculation from a nominal concentration cannot capture every solution-specific effect. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What is the equation for pH?
pH = −log₁₀[H₃O⁺], using hydronium concentration in mol/L as a dilute-solution approximation. The more rigorous definition uses hydronium activity.
What is the equation for pOH?
pOH = −log₁₀[OH⁻], where hydroxide concentration is expressed in mol/L. A tenfold decrease in hydroxide concentration raises pOH by one unit.
How do you calculate pH from pOH?
At 25 °C in dilute aqueous solution, pH ≈ 14.00 − pOH. At another temperature, use pH + pOH = pKw with the appropriate temperature-dependent pKw.
Is pH + pOH always 14?
No. The sum equals pKw, which is approximately 14.00 at 25 °C and changes with temperature. Concentrated solutions can also require activities rather than simple concentrations.
Can pH be negative or greater than 14?
Yes. Those values are possible, especially for highly concentrated solutions, although ordinary dilute aqueous solutions commonly fall between 0 and 14. Activity effects make simple concentration-based estimates less reliable in extreme conditions.
Related
Formula used
in h | Hydronium concentration | mol/L | 0.00001 | 0 in oh | Hydroxide concentration | mol/L | 0.000001 | 0 in t | Temperature | °C | 25 | -273.15 out ph | pH from hydronium concentration | - | -log10(h) | 2 out poh | pOH from hydroxide concentration | - | -log10(oh) | 2 out kw | Water ion-product pKw | - | -log10(10^(-14) * exp((t - 25) * 0.055) / exp((t - 25) * 0.055)) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- Mass Fraction to Molar Fraction Calculator
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- K2 Molar Mass Calculator and Calculation78.1966 g/mol