molecalculator

Moles & Molar Mass

pH to OH Calculator: Convert pH to pOH and [OH⁻]

Calculator No. 01-4441 · Updated · Formula and assumptions shown below

pOH 7.00
Hydroxide concentration
1.000 × 10−7 mol/L
= 10 ^ (-(14 − pH))
pH
7
Set in the form below
Temperature
25 °C
Set in the form below
You enter
pH, Temperature (°C)
You get
pOH, Hydroxide concentration (mol/L)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A pH to OH calculator converts a solution’s pH into its pOH and, when temperature is specified, its hydroxide-ion concentration, [OH⁻]. Enter pH and temperature in °C; the calculator returns pOH and [OH⁻] in mol/L using the water-ionization relationship.

Formula

At 25 °C, pH + pOH = 14.00, so pOH = 14.00 − pH. Hydroxide concentration follows from pOH = −log₁₀[OH⁻], giving [OH⁻] = 10−pOH mol/L. In these formulas, pH and pOH are dimensionless logarithmic values; [OH⁻] is the hydroxide concentration in moles per liter (mol/L).

The calculator’s pOH expression is 14 + 0 × √(T + 273.15) − pH. The zero-times-square-root term does not affect the result; it keeps the temperature input’s lower physical limit explicit. The concentration expression substitutes the same pOH formula into 10−pOH. The conversion from pH to concentration uses base-10 logarithms, not natural logarithms.

The value 14.00 is the conventional pKw of water at 25 °C, where pKw = −log₁₀Kw and pH + pOH = pKw. It is not a universal constant for every temperature. This calculator accepts temperature so the stated conditions are visible, but its formula uses 14.00 at every temperature; its result is therefore a 25 °C approximation, not a temperature-corrected calculation.

Worked Example

Using the defaults, pH = 7 and temperature = 25 °C:

  1. Convert the temperature to kelvin: 25 + 273.15 = 298.15 K.
  2. Calculate pOH: 14 + 0 × √(298.15) − 7 = 7.
  3. Calculate hydroxide concentration: [OH⁻] = 10−7 = 0.00000010 mol/L = 1.0000 × 10−7 mol/L.

The calculator displays pOH as 7.00 and hydroxide concentration as 1.0000 × 10−7 mol/L. The latter is also 0.1000 µmol/L, because 1 mol/L = 1,000,000 µmol/L.

Assumptions

  • The pH + pOH = 14.00 relationship assumes water at 25 °C.
  • The calculated concentration is an ideal, concentration-based estimate; actual ion activities can differ, especially in concentrated or high-ionic-strength solutions.
  • Temperature is recorded and converted to kelvin in the expression, but does not adjust pKw; the output is not temperature-corrected.
  • The calculation interprets the entered pH as a valid value from 0 to 14. Real measured pH values can sometimes fall outside this conventional range.

What “pH to OH” Means

“OH” usually means hydroxide ions, OH⁻. A pH-to-OH calculation may refer to either finding pOH or converting pH into hydroxide concentration. These are related but different results: pOH is a dimensionless logarithmic value, while [OH⁻] is a concentration with units.

For a neutral solution at 25 °C, pH and pOH are both 7, and the ideal hydroxide concentration is 10−7 mol/L. If pH is 10, pOH is 4 and the estimated hydroxide concentration is 10−4 mol/L. If pH is 3, pOH is 11 and [OH⁻] is 10−11 mol/L. Each one-unit increase in pH corresponds to a tenfold decrease in pOH and a tenfold increase in hydroxide concentration under the 25 °C relationship.

Hydroxide concentration is not the same thing as the total amount of hydroxide in a sample. To calculate amount in moles, concentration must be multiplied by solution volume in liters. Nor does a calculated concentration alone identify which base, salt, or reaction produced the hydroxide.

How to Read and Use the Result

Use the calculator when you have a pH value and want its corresponding pOH or an approximate hydroxide concentration under the standard 25 °C convention. The pH can come from a measurement or a supplied problem value. For practical work, the meter reading is the real check: temperature and ionic strength shift pH, and an estimate from a simple conversion does not replace measurement.

  • pOH describes hydroxide on a logarithmic scale. A smaller pOH corresponds to a greater hydroxide concentration.
  • [OH⁻] is the estimated concentration in mol/L. Scientific notation makes very small values easier to read.
  • Temperature documents the sample condition but, in this calculator, does not change the assumed pKw. Do not interpret its output as a temperature-adjusted equilibrium value.

If a pH reading has limited precision, avoid reporting a concentration with unjustified precision. Because the conversion is exponential, a small pH uncertainty can cause a substantial relative uncertainty in [OH⁻]. For example, a change of 0.1 pH unit corresponds to a factor of about 100.1, or 1.26, in concentration.

Temperature, Activities, and Limitations

Water’s ionization changes with temperature, so pKw is not always 14.00. For a temperature-specific result, use a reliable value of pKw for the stated conditions and calculate pOH = pKw − pH, then [OH⁻] = 10−pOH mol/L. Since this page’s calculator does not include a pKw table or an input for that constant, its outputs should be treated as estimates based on the familiar 25 °C relationship.

There is another distinction in more exact chemistry: pH is defined in terms of hydrogen-ion activity, not simply its concentration. In dilute solutions, activity and concentration are often close enough for introductory calculations. In concentrated solutions or mixtures with substantial dissolved salts, they can differ; likewise, concentrations inferred from pH are not always identical to measured analytical concentrations.

Do not assume that pH 7 is neutral at every temperature. Neutrality means equal hydrogen-ion and hydroxide-ion activities. Their equal values change as water’s ionization changes, so a neutral sample at a temperature other than 25 °C can have a pH other than 7.

Common Mistakes

  • Subtracting pH from 14 at any temperature: this is the standard 25 °C shortcut. At other temperatures, the appropriate pKw is needed.
  • Confusing pOH with [OH⁻]: pOH is a logarithmic number; [OH⁻] is expressed in mol/L.
  • Using 10pOH instead of 10−pOH: the negative exponent is essential. A higher pOH means less hydroxide.
  • Calling pH 7 universally neutral: pH 7 is neutral under the usual 25 °C convention, not a temperature-independent definition.
  • Reporting excessive digits: calculator precision does not remove uncertainty in the pH measurement, temperature, or activity effects.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

How do I calculate OH⁻ from pH?
At 25 °C, calculate pOH = 14.00 − pH, then calculate [OH⁻] = 10−pOH mol/L. For another temperature, use the pKw appropriate to that condition instead of assuming 14.00.

What is the OH⁻ concentration at pH 7?
Using the 25 °C relationship, pOH is 7 and [OH⁻] is 1 × 10−7 mol/L. This is the ideal concentration estimate for a neutral solution under that convention.

Is pOH always 14 minus pH?
No. More generally, pH + pOH = pKw. The value 14.00 is the conventional approximation for water at 25 °C; pKw changes with temperature.

Does a higher pH mean more hydroxide?
At a fixed temperature, yes: increasing pH by one unit increases the inferred hydroxide concentration tenfold under the pH–pOH relationship.

Why is my measured pH different from the calculator’s estimate?
The calculator converts the entered pH using an assumed equilibrium relationship; it does not predict or correct a measurement. Temperature, dissolved ions, calibration, sample composition, and activity effects can all influence measured values.

Related

Formula used
in ph | pH | - | 7 | 0 | 14
in t | Temperature | °C | 25 | -273.15
out poh | pOH | - | 14 - ph | 2
out oh | Hydroxide concentration | mol/L | 10 ^ (-(14 - ph)) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →