molecalculator

Moles & Molar Mass

Hydrostatic Pressure: Density × Gravity × Height

Calculator No. 01-2132 · Updated · Formula and assumptions shown below

Hydrostatic gauge pressure 98,066.50 Pa
Hydrostatic gauge pressure
98.0665 kPa
= Hydrostatic gauge pressure ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
Gravitational acceleration
9.80665 m/s^2
Set in the form below
You enter
Fluid density (kg/m^3), Gravitational acceleration (m/s^2), Vertical depth (m)
You get
Hydrostatic gauge pressure (Pa), Hydrostatic gauge pressure (kPa)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Hydrostatic pressure from a liquid column is calculated as pressure = density × gravitational acceleration × height, or p = ρgh. Enter the liquid density, gravity, and vertical depth to calculate the pressure increase; the result is in pascals (Pa). This calculator gives gauge pressure from the liquid alone, not the total pressure including the atmosphere.

Formula

The hydrostatic pressure difference across a stationary fluid column is p = ρgh. Here, p is gauge pressure in pascals (Pa), ρ is fluid density in kilograms per cubic metre (kg/m³), g is gravitational acceleration in metres per second squared (m/s²), and h is vertical depth in metres (m). One pascal equals one newton per square metre, and the units reduce as (kg/m³)(m/s²)(m) = kg/(m·s²) = Pa. The second output converts pascals to kilopascals using 1 kPa = 1000 Pa.

The equation calculates the pressure increase between two heights in a fluid of constant density. It does not include pressure already acting on the fluid’s surface. For a surface exposed to air, absolute pressure at depth is approximately atmospheric pressure plus ρgh.

Worked Example

Using the calculator’s default values—density 1000 kg/m³, gravity 9.80665 m/s², and vertical depth 10 m:

  1. Calculate the pressure increase: p = 1000 × 9.80665 × 10 = 98,066.5 Pa.
  2. Convert to kilopascals: 98,066.5 / 1000 = 98.0665 kPa, which rounds to 98.0665 kPa at four decimal places.

The calculator displays the headline result to two decimal places: 98,066.50 Pa. This is gauge pressure, the increase above the pressure at the liquid surface.

Assumptions

  • The fluid is stationary and has uniform density throughout the depth.
  • The height is the vertical distance between the point of interest and the fluid surface, not the length of a sloping path.
  • The result is gauge pressure from the fluid column; surface or atmospheric pressure is excluded.
  • Gravity is treated as constant over the height being considered.

How the Relationship Works

A fluid’s weight presses on the material below it. At greater depth, more fluid lies above a point, so pressure increases. Density describes how much mass occupies a given volume; gravity converts that mass into weight. Multiplying density by gravity and vertical depth gives the force per unit area associated with the column.

For a liquid with changing density, the more general relationship is an integral: pressure difference = ∫ρg dh, where density may vary with height. For ordinary water tanks, density changes are small enough that using a representative constant density is usually appropriate. In gases, density can change appreciably with altitude, so a single-density calculation may be only an approximation over a large height range.

Choosing Inputs and Reading the Result

  • Density: Use the fluid’s density in kg/m³. Water is often approximated as 1000 kg/m³ for basic calculations, but its actual density depends on temperature and composition. For another liquid, use a value appropriate to its conditions.
  • Gravity: The standard gravity value is 9.80665 m/s². Local gravitational acceleration varies slightly with location; the standard value is suitable for most general-purpose estimates.
  • Height: Measure vertically from the surface to the point where pressure is wanted. A container’s total height is not necessarily the depth if it is partly filled.
  • Output units: Pa is the SI pressure unit. The calculator also shows kPa; 100 kPa equals 100,000 Pa.

For example, a 2 m water column at the default density and gravity produces 1000 × 9.80665 × 2 = 19,613.3 Pa, or 19.6133 kPa of gauge pressure. This does not mean every point in a 2 m-tall container has that pressure: pressure depends on depth below the surface.

Gauge Pressure, Absolute Pressure, and Common Mistakes

A frequent misunderstanding is to treat ρgh as the full absolute pressure. It is the pressure difference caused by the liquid column. If the liquid surface is open to the atmosphere, approximate absolute pressure is pabsolute = patmospheric + ρgh. Near sea level, atmospheric pressure is about 101.3 kPa, but it varies with weather and elevation. If the surface is in a sealed vessel, use the pressure at that surface instead of automatically adding atmospheric pressure.

Other common errors include mixing units, using the length of a pipe instead of vertical depth, and confusing mass density with specific weight. This formula expects density in kg/m³, not g/cm³; 1 g/cm³ equals 1000 kg/m³. It expects height in metres, so a depth in centimetres must be divided by 100 before entering it. Specific weight already includes gravity, so multiplying it by gravity again would count gravity twice.

Applications and Limits

The relationship is useful for estimating pressure at the bottom of a tank, the pressure difference across a dam or submerged surface, and the effect of liquid depth in a connected vessel. In an open tank, two points at the same depth in the same continuous, stationary liquid have the same hydrostatic pressure, regardless of the vessel’s shape. A narrow, wide, or irregular container does not change pressure at a given depth when the fluid and conditions are the same.

This equation does not calculate pressure losses from flowing liquid, impact pressure, or pressure changes due to pumps. It also does not tell whether a tank or structure can withstand a pressure; that depends on materials, geometry, defects, and applicable engineering design requirements. For changing density, moving fluids, or safety-critical equipment, use the appropriate engineering model and verified material data.

Frequently Asked Questions

What does density × gravity × height calculate?
It calculates the hydrostatic pressure difference caused by a stationary fluid column: p = ρgh. The answer is a pressure, not a force or a total pressure that automatically includes the atmosphere.

What units should I use for ρgh?
Use density in kg/m³, gravity in m/s², and vertical height in metres. The resulting unit is Pa. Divide pascals by 1000 to express the result in kPa.

Does pressure depend on the shape of the container?
At a given depth in the same stationary fluid, pressure does not depend on the container’s shape. It depends on the fluid density, gravity, and vertical depth below the surface.

How do I calculate absolute pressure underwater?
Calculate the hydrostatic increase with ρgh, then add the pressure acting at the surface. For an open body of water, that is local atmospheric pressure; for a sealed system, it is the pressure inside the sealed space.

Why does water pressure increase with depth?
A deeper point supports the weight of a taller column of water above it. Since that weight acts over an area, the force per area—and therefore the pressure—increases with depth.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0
in h | Vertical depth | m | 10 | 0
out p | Hydrostatic gauge pressure | Pa | rho * g * h | 2
out pk | Hydrostatic gauge pressure | kPa | p / 1000 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →