This calculator estimates the pressure change caused by a fluid column using the hydrostatic relation ΔP = ρgh. Enter the fluid’s density, the vertical depth, and gravitational acceleration; it returns gauge pressure, with the corresponding absolute pressure shown when you also enter the surface pressure.
Formula
For a fluid at rest with constant density, the hydrostatic pressure increase with depth is:
ΔP = ρgh
- ΔP is the pressure increase from the fluid’s surface to the point below it, in pascals (Pa).
- ρ (rho) is fluid density, in kilograms per cubic metre (kg/m³).
- g is gravitational acceleration, in metres per second squared (m/s²).
- h is vertical depth below the fluid surface, in metres (m).
Pressure at depth is P = Ps + ρgh, where Ps is the absolute pressure at the surface, in Pa. The calculator reports the increase as its first result, then adds the entered surface pressure to give absolute pressure. The units reduce to pressure: (kg/m³)(m/s²)(m) = kg/(m·s²) = Pa.
Worked Example
Using the defaults—water density 1000 kg/m³, depth 10 m, gravitational acceleration 9.80665 m/s², and surface pressure 101325 Pa:
ΔP = ρgh = (1000 kg/m³)(9.80665 m/s²)(10 m) = 98066.5 Pa, or 98066.50 Pa to two decimal places.
P = Ps + ΔP = 101325 Pa + 98066.5 Pa = 199391.50 Pa absolute pressure.
The pressure increase is about 98.07 kPa, while the absolute pressure is about 199.39 kPa. The latter includes the approximately 101.33 kPa surface atmospheric pressure entered in the example.
Assumptions
- The fluid is at rest and has uniform density throughout the stated depth.
- The depth is measured vertically, not along a sloping path.
- Gravitational acceleration is constant over the depth.
- The surface pressure is absolute pressure; the default is standard atmospheric pressure, 101325 Pa.
- The calculation does not account for flow, changes in temperature, or density variation with pressure.
What the Equation Means
Pressure is force per area. In a stationary liquid, the weight of fluid above a point produces greater pressure at greater depth. The relation ΔP = ρgh quantifies that added pressure. It is commonly called the hydrostatic pressure equation, not a universal equation linking density and pressure for every material or situation.
Density and pressure are connected in this equation through the fluid column: for a fixed depth and gravity, doubling density doubles the pressure increase. Likewise, doubling the vertical depth doubles the increase. But pressure does not by itself determine density. To infer density from pressure, the depth, gravity, and applicable physical model must also be known.
In the worked example, the extra pressure from ten metres of water is around 98 kPa. This is gauge pressure: pressure measured relative to the surface pressure. Absolute pressure uses a reference of perfect vacuum, so it includes the surface pressure as well. Confusing these two readings is a frequent source of apparent disagreement.
When This Relation Applies
The equation is useful for estimating pressure at a known depth in a calm liquid, comparing pressure at different depths, or calculating the load a liquid column adds. It also applies to a fluid at rest in a container: the shape of the container does not change the pressure at a given depth if the fluid and conditions are the same.
For gases, the same simple calculation can be a useful approximation over a small height range when density is nearly constant. Over large altitude differences, gas density changes appreciably, so a model that accounts for changing density is needed. Flowing fluids also require additional treatment; velocity, friction, and geometry can affect pressure.
For a fluid whose density varies with height, use the more general hydrostatic relation:
ΔP = ∫ ρ(z)g(z) dz
The integral adds the contribution from each thin layer between the surface and the point of interest. The calculator uses the simpler constant-density form and should not be treated as a substitute when stratification, strong compression, or changing gravity matters.
Density, Units, and Common Errors
Density is mass per volume. Water near ordinary room temperature has a density close to 1000 kg/m³, but its exact density depends on temperature and composition. Seawater is denser than fresh water, and oils vary by composition. Use a value appropriate to the actual fluid and conditions rather than assuming every liquid has water’s density.
- Keep units consistent. The calculator expects kg/m³, metres, m/s², and pascals. A depth in centimetres must be converted to metres by dividing by 100; a density in g/cm³ must be multiplied by 1000 to get kg/m³.
- Use vertical depth. A 10 m vertical column has the same hydrostatic increase whether its container is wide or narrow. A 10 m sloping distance does not necessarily represent 10 m of depth.
- Do not omit surface pressure when absolute pressure is wanted. ΔP alone is the gauge increase, not absolute pressure.
- Do not confuse pressure with density. Their units differ, and the equation needs depth and gravity to relate them.
Rounding density or depth too early can affect the final result. Keep the input values at their justified precision and round only the reported answer to a sensible number of significant figures.
Frequently Asked Questions
What is the equation relating pressure and density?
For a fluid at rest with constant density, pressure increase with depth is ΔP = ρgh. Here, ρ is density, g is gravitational acceleration, and h is vertical depth.
Does pressure increase when density increases?
Yes, for the same depth and gravitational acceleration, the hydrostatic pressure increase is proportional to density. This does not mean pressure alone determines density in every setting.
What is the pressure at depth h?
Absolute pressure is P = Ps + ρgh, where Ps is the absolute surface pressure. If you need gauge pressure relative to the surface, use ρgh alone.
Is pressure equal to density times gravity?
No. Density times gravity has units of pressure per length. Multiplying by a vertical depth gives a pressure difference: ΔP = ρgh.
Does the equation work for air?
It can approximate pressure change over a limited height when air density is nearly constant. For substantial altitude changes, density varies, so a more complete atmospheric model is needed.
Does container shape affect hydrostatic pressure?
No, not at a given depth in the same stationary fluid under the same conditions. The pressure depends on density, gravity, and vertical depth, not the container’s shape.
Related
Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0 in h | Vertical depth | m | 10 | 0 in g | Gravitational acceleration | m/s^2 | 9.80665 | 0 in ps | Surface absolute pressure | Pa | 101325 | 0 out dp | Pressure increase | Pa | rho * g * h | 2 out p | Absolute pressure at depth | Pa | ps + dp | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Pressure Difference, Height, Density, and Gravity Calculator9,806.65 Pa
- Pressure Divided by Density: Meaning and Calculation101.325 J/kg
- Pressure Density Volume Formula for an Ideal Gas97,993.418 Pa
- Hydrostatic Pressure: Density × Gravity × Height98,066.50 Pa
- Pressure Density Depth Formula for Fluids98,066 Pa
- Pressure Density Temperature Equation Calculator100,961.74 Pa