molecalculator

Moles & Molar Mass

Pressure rho g h Calculator: Hydrostatic Pressure

Calculator No. 01-11950 · Updated · Formula and assumptions shown below

Hydrostatic pressure 98,100.0 Pa
Pressure in kilopascals
98.10 kPa
= Hydrostatic pressure ÷ 1000
Pressure in bar
0.9810 bar
= Hydrostatic pressure ÷ 100000
Fluid density (rho)
1000 kg/m³
Set in the form below
You enter
Fluid density (rho) (kg/m³), Depth or height of fluid column (m), Gravitational acceleration (m/s²)
You get
Hydrostatic pressure (Pa), Pressure in kilopascals (kPa), Pressure in bar (bar)
Rounding
1 dp · 2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the hydrostatic pressure exerted by a fluid column using the formula p = ρgh. You enter the fluid density, the depth (or height of the fluid column), and the gravitational acceleration, and it returns the pressure in pascals (Pa). The result is the gauge pressure at that depth, not including atmospheric pressure on the surface.

Formula

The hydrostatic pressure equation is written as:

p = ρ × g × h

  • p – hydrostatic pressure, in pascals (Pa = N/m²)
  • ρ (rho) – fluid density, in kilograms per cubic metre (kg/m³)
  • g – gravitational acceleration, in metres per second squared (m/s²). Standard value 9.80665 m/s², often rounded to 9.81 m/s²
  • h – depth below the fluid surface (or height of the column), in metres (m)

This formula assumes the fluid is incompressible (density constant with depth) and that the only force is gravity. It gives the pressure due to the fluid alone; to get absolute pressure you must add the atmospheric pressure at the surface (about 101,325 Pa at sea level).

Worked Example

Using the default values from the calculator: density ρ = 1000 kg/m³ (fresh water), depth h = 10 m, and g = 9.81 m/s².

Step 1 – Multiply density by gravity:
1000 kg/m³ × 9.81 m/s² = 9810 kg/(m²·s²) = 9810 N/m³ (this is the specific weight of water)

Step 2 – Multiply by depth:
9810 N/m³ × 10 m = 98,100 N/m² = 98,100 Pa

So the hydrostatic pressure at 10 m depth in fresh water is 98,100 Pa, which is 98.1 kPa or 0.981 bar. The calculator rounds the first output to 1 decimal place, so it shows 98100.0 Pa.

Assumptions

  • The fluid is incompressible – density is constant with depth.
  • The fluid is static – no motion or viscosity effects.
  • Gravity is uniform over the depth considered.
  • The pressure is measured as gauge pressure (relative to the surface).
  • The depth h is measured vertically from the free surface, not along a slanted pipe.

When to Use This Calculator

Use this calculator whenever you need the pressure at a point inside a static fluid column. Common situations include:

  • Finding the pressure at the bottom of a tank, reservoir, or swimming pool.
  • Calculating the pressure exerted by a column of mercury in a barometer (density 13,600 kg/m³).
  • Estimating the pressure on a submerged object or a dam wall at a given depth.
  • Converting between head (metres of fluid) and pressure for pump systems.

It is not for gases (which are compressible – density changes with pressure) unless the gas column is very short and the density is known. It is also not for moving fluids, where Bernoulli’s equation and dynamic pressure come into play.

How to Read the Result

The result is the pressure at the depth you entered, in pascals. One pascal is one newton per square metre – a very small pressure. For everyday values, you will often convert to kilopascals (1 kPa = 1000 Pa) or bar (1 bar = 100,000 Pa).

Remember that this is gauge pressure. If you need absolute pressure (for example, when calculating boiling points or gas behaviour), add atmospheric pressure. At sea level, absolute pressure at 10 m depth in fresh water is 98,100 Pa + 101,325 Pa = 199,425 Pa ≈ 1.99 bar.

The calculator also shows the pressure in kPa and bar for convenience. For salt water (density about 1025 kg/m³), the pressure at the same depth would be about 2.5% higher.

Common Mistakes and Misconceptions

  • Mixing units: The formula only works in SI units. If you have depth in feet and density in g/cm³, convert first: 1 ft = 0.3048 m, 1 g/cm³ = 1000 kg/m³. A common error is using cm of water without converting to metres.
  • Forgetting that h is vertical depth: If a pipe is slanted, h is the vertical drop, not the pipe length. Only the vertical component matters for pressure.
  • Assuming the formula gives total pressure: It gives pressure due to the fluid column, not including the atmosphere above. Many real-world problems ask for gauge pressure, but some ask for absolute – read the question.
  • Using density of the fluid, not the object: For a submerged object, the pressure depends on the fluid’s density, not the object’s.
  • Confusing pressure with force: Pressure is force per area. To get the total force on a surface, you must integrate pressure over the area (for a flat horizontal surface, force = pressure × area).

Real-World Context and Comparisons

Hydrostatic pressure explains many everyday phenomena. The pressure increases by about 1 atmosphere (101.3 kPa) for every 10.3 m of water depth (since 101,325 Pa / (1000 × 9.81) ≈ 10.33 m). Divers feel this as increased pressure on their ears; at 20 m depth, the absolute pressure is about 3 atmospheres.

In engineering, this formula is used to design dams, submarine hulls, and water towers. The pressure at the bottom of a water tower depends only on the height of the water surface, not on the width of the tank – which is why tall narrow towers work as well as wide ones.

For mercury (density 13,600 kg/m³), a column of 760 mm (0.76 m) produces a pressure of 13,600 × 9.81 × 0.76 = 101,325 Pa – exactly one standard atmosphere. That is the basis of the mercury barometer.

For comparison, blood pressure is usually measured in mmHg (millimetres of mercury). A reading of 120 mmHg corresponds to a pressure of 120/760 × 101,325 ≈ 16,000 Pa, or 16 kPa.

Limits of the Formula

The p = ρgh formula is an approximation that works well for most liquids under normal conditions, but it has limits:

  • Compressibility: For very deep oceans (thousands of metres), water density increases slightly with pressure. The error is small (about 2% at 10 km depth) but not zero.
  • Temperature: Density changes with temperature. For water, density is highest at 4°C (1000 kg/m³) and decreases as it warms. For precise work, use the density at your actual temperature.
  • Non-Newtonian fluids: The formula assumes a simple fluid. For slurries or fluids with suspended solids, density may vary.
  • Gravity variation: g varies slightly with altitude and latitude (from about 9.78 to 9.83 m/s²). For most calculations, 9.81 is fine, but for high precision use the local value.

For gases, you cannot use this formula directly because density changes with pressure. Instead, you would use the ideal gas law or barometric formula.

Frequently Asked Questions

Does the shape of the container affect hydrostatic pressure? No. At a given depth, the pressure depends only on the density of the fluid, gravity, and the depth – not on the width or shape of the container. This is known as the hydrostatic paradox: a narrow tube and a wide tank with the same water height exert the same pressure at the bottom.

What is the difference between gauge pressure and absolute pressure? Gauge pressure is the pressure above atmospheric pressure. Absolute pressure is the total pressure including atmospheric. The p = ρgh formula gives gauge pressure; absolute pressure = gauge pressure + atmospheric pressure (about 101.3 kPa at sea level).

How do I convert pressure from pascals to psi? 1 psi = 6894.76 Pa. So divide the pressure in pascals by 6894.76. For example, 98,100 Pa / 6894.76 ≈ 14.23 psi.

Can I use this calculator for seawater? Yes, but you need the correct density. Seawater density is typically about 1025 kg/m³, but it varies with salinity and temperature. Enter 1025 in the density field to get a more accurate result for ocean depths.

Why do my ears pop when I go underwater? The hydrostatic pressure increases with depth, compressing the air in your middle ear. At just a few metres depth, the pressure difference is enough to make your eardrum flex. Equalising by swallowing or yawning helps balance the pressure.

What is the pressure at the bottom of a 10 m swimming pool? Using fresh water (1000 kg/m³) and g = 9.81 m/s², the gauge pressure is 98,100 Pa (98.1 kPa). The absolute pressure is 98,100 + 101,325 = 199,425 Pa, about 2 bar.

Related

Formula used
in d | Fluid density (rho) | kg/m³ | 1000 | 0
in h | Depth or height of fluid column | m | 10 | 0
in g | Gravitational acceleration | m/s² | 9.81 | 0
out p | Hydrostatic pressure | Pa | d * g * h | 1
out pkpa | Pressure in kilopascals | kPa | p / 1000 | 2
out pbar | Pressure in bar | bar | p / 100000 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →