molecalculator

Moles & Molar Mass

Pseudo First Order Kinetics Equation and Calculator

Calculator No. 01-6547 · Updated · Formula and assumptions shown below

Concentration of A remaining 0.0549 mol/L
Half-life
34.657 s
Result, rounded to 3 decimal places
Initial concentration of A
0.1 mol/L
Set in the form below
Observed rate constant
0.02 s^-1
Set in the form below
You enter
Initial concentration of A (mol/L), Observed rate constant (s^-1), Elapsed time (s)
You get
Concentration of A remaining (mol/L), Half-life (s)
Rounding
4 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The pseudo first order rate equation is −d[A]/dt = kobs[A], which integrates to ln([A]t/[A]0) = −kobst. This calculator uses an initial concentration, observed rate constant, and elapsed time to find the concentration remaining; it also reports the reaction half-life.

Formula

For a reaction that behaves as first order in reactant A under specified conditions, its disappearance rate is −d[A]/dt = kobs[A]. The integrated equation used by the calculator is [A]t = [A]0e−kobst.

  • [A]0 is the initial concentration of A, in mol/L.
  • [A]t is the concentration remaining after time t, in mol/L.
  • kobs is the observed, or pseudo first order, rate constant, in s−1 when time is entered in seconds.
  • t is elapsed time, in seconds.

The half-life is t1/2 = ln(2)/kobs. The displayed calculator outputs use the same units as the corresponding inputs. The equations assume a constant observed rate constant over the interval and a first-order concentration dependence in A. A zero rate constant gives no concentration change; its half-life is undefined because division by zero is not possible.

Worked Example

Using the defaults, [A]0 = 0.100 mol/L, kobs = 0.0200 s−1, and t = 30 s:

  1. Calculate the dimensionless exponent: −kobst = −(0.0200 s−1)(30 s) = −0.60000.
  2. Calculate the remaining fraction: e−0.60000 = 0.54881.
  3. Multiply by the initial concentration: [A]t = (0.100 mol/L)(0.54881) = 0.05488 mol/L.
  4. Calculate half-life: t1/2 = ln(2)/(0.0200 s−1) = 34.657 s, or 34.7 s to the calculator’s displayed precision.

Thus the calculator reports 0.0549 mol/L remaining and a half-life of 34.7 s. These are mathematical outputs for the stated inputs, not a fitted result from experimental measurements.

Assumptions

  • The reaction is first order in A under the conditions represented by kobs.
  • The observed rate constant stays constant during the chosen time interval.
  • Concentration is expressed in mol/L and time in seconds, making kobs units s−1.
  • The expression describes concentration remaining, not the concentration of a product or the reaction’s equilibrium composition.

What Pseudo First Order Means

A reaction’s rate law can depend on more than one reactant. For example, for A + B → products, a possible rate law is rate = k[A][B], where k is the true second-order rate constant. If B is present in large excess, its concentration may change so little that it is treated as approximately constant during the experiment. Then k[B] can be combined into an observed constant, kobs = k[B], and the rate becomes rate ≈ kobs[A].

The reaction has not literally changed its underlying molecular mechanism or become first order in every reactant. Rather, under the excess-reactant approximation, the measured change in A follows a first-order form. If the original rate law is rate = k[A][B]n, holding B approximately constant gives kobs = k[B]n. The units of kobs are then inverse time, regardless of the units of the underlying k.

How to Use the Equation

Enter the initial concentration of the reactant being tracked, the observed rate constant for the experimental conditions, and the elapsed time. Keep the units consistent: this calculator expects mol/L, s−1, and seconds. If the rate constant is reported in min−1, convert it to s−1 by dividing by 60; alternatively, convert the time to minutes and use the rate constant in min−1 when evaluating the equation separately.

  • Use kobs determined or reported for the same temperature, solvent, pH, and excess-reactant concentration as the situation being analyzed.
  • Enter elapsed time from the chosen initial measurement, not from an unrelated start point.
  • Interpret [A]t as the remaining concentration. The amount consumed is [A]0 − [A]t if the simple one-reactant disappearance model applies.
  • Use the half-life output to compare timescales: after one half-life, half remains; after two, one quarter remains under constant first-order conditions.

Checking the Model and Common Mistakes

A straight-line test can help determine whether first-order behavior is plausible. Measure [A] at several times and plot ln[A] against time. The integrated equation predicts a line with slope −kobs and intercept ln[A]0. A curved trend may indicate that the pseudo-first-order approximation fails, the rate constant changes, multiple pathways contribute, or the concentration measurements have systematic problems.

A frequent mistake is to treat kobs as the underlying rate constant for the full reaction. In the A + B example, kobs includes the approximately fixed concentration of B; its numerical value and units therefore depend on B’s concentration. Another mistake is mixing time units: multiplying a value in min−1 by seconds produces an incorrect exponent unless a conversion is made.

Concentrations must be positive for the logarithmic integrated form and physically meaningful as concentrations. Rounding k or time too early can noticeably alter the exponential result, especially over long intervals. Use full precision for intermediate calculations and round only the final reported value to a precision justified by the measurements.

Limits and Related Rate Laws

The equation is useful only while its assumptions are reasonable. If the excess reactant is not truly in excess, its concentration can fall enough to affect the rate, so kobs is no longer constant. If temperature or other conditions change, the rate constant may change as well. In those cases, use the full rate law or an appropriate model rather than forcing a pseudo-first-order fit.

First-order disappearance is also distinct from zero-order and second-order behavior. For a zero-order process, concentration decreases linearly with time; for a simple second-order process in one reactant, the reciprocal concentration is linear with time. Choosing a model from a single measurement is not reliable: multiple time points and a suitable comparison of fits are generally more informative.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. The calculator is for study and lab-planning arithmetic; it does not establish that a reaction follows a particular mechanism or replace experimental validation.

Frequently Asked Questions

What is the pseudo first order kinetics equation?
The differential form is −d[A]/dt = kobs[A]. Its integrated form is [A]t = [A]0e−kobst.

How do you calculate the pseudo first order rate constant?
For a reaction first order in A and B, with B held approximately constant, kobs = k[B]. More generally, estimate kobs from the negative slope of ln[A] versus time when that plot is linear.

What are the units of kobs?
They are units of inverse time, such as s−1 or min−1. Use the matching time unit in the integrated equation.

Why is the reaction called pseudo first order?
The original rate law may involve multiple reactants, but one reactant is maintained at an approximately constant, often large-excess concentration. Combining that concentration with the true rate constant produces an observed constant and a first-order-looking rate law in the tracked reactant.

Does pseudo first order mean the reaction mechanism is first order?
No. It describes the observed rate dependence under specified conditions; it does not by itself establish the reaction mechanism or the full rate law.

Related

Formula used
in a | Initial concentration of A | mol/L | 0.100 | 0
in k | Observed rate constant | s^-1 | 0.0200 | 0
in t | Elapsed time | s | 30 | 0
out ct | Concentration of A remaining | mol/L | a * exp(-k * t) | 4
out th | Half-life | s | ln(2) / k | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →