This calculator estimates the linear thermal expansion of a PTFE (polytetrafluoroethylene) part when its temperature changes. You enter the original length, the starting temperature, and the ending temperature, and it returns the expected change in length and the final length, using the material’s published coefficient of thermal expansion. The result helps you plan for clearances, tolerances, and stress in applications where PTFE is used alongside metals or other rigid materials.
Formula
The linear thermal expansion of a solid is given by:
ΔL = α × L₀ × ΔT
- ΔL = change in length (mm, same unit as L₀)
- α = coefficient of linear thermal expansion (1/°C or 1/K). For PTFE, the commonly used value is 120 × 10⁻⁶ /°C (120 μm/m·°C).
- L₀ = original length (mm)
- ΔT = temperature change (ending temperature − starting temperature, °C or K)
The calculator uses α = 120 × 10⁻⁶ /°C. This is an average value for molded PTFE over the range 20–100 °C. Actual values vary with grade, crystallinity, and temperature, typically between 100 and 160 × 10⁻⁶ /°C.
Worked Example
Using the default values: L₀ = 100 mm, T₁ = 20 °C, T₂ = 80 °C.
ΔT = 80 − 20 = 60 °C
ΔL = 120 × 10⁻⁶ × 100 × 60 = 0.72 mm
Final length = 100 + 0.72 = 100.72 mm
Strain = 0.72 / 100 = 0.0072 (0.72%)
So a 100 mm PTFE rod heated from 20 °C to 80 °C grows by 0.72 mm. The calculator shows 0.720 mm for ΔL and 100.720 mm for the final length.
Assumptions
- Linear expansion is uniform and isotropic (same in all directions).
- The coefficient α is constant over the temperature range. In reality, PTFE’s α increases at higher temperatures, especially above 50 °C.
- The material is free to expand – no external constraints. If the part is clamped or bonded, internal stresses will develop instead of free expansion.
- No phase transitions occur. PTFE has a crystalline transition near 19 °C that causes a small volume change, which this simple model ignores.
Why PTFE Expands So Much
PTFE has one of the highest thermal expansion coefficients among engineering plastics. Typical values:
- PTFE: 120–160 × 10⁻⁶ /°C
- Nylon 66: 80 × 10⁻⁶ /°C
- Polycarbonate: 70 × 10⁻⁶ /°C
- Aluminum: 23 × 10⁻⁶ /°C
- Steel: 11–13 × 10⁻⁶ /°C
This means PTFE expands about 5–10 times more than metals. In a 1-meter part, a 50 °C temperature rise causes roughly 6 mm of expansion (120e-6 × 1000 × 50 = 6 mm). That is enough to cause buckling, seal failure, or cracking if the part is confined.
PTFE’s high expansion comes from its weak intermolecular forces. The carbon-fluorine bonds are strong, but the polymer chains slide past each other easily, so heat energy translates into large dimensional changes.
How to Use the Calculator
Follow these steps:
- Measure the original length of the PTFE part in the direction you care about (mm, cm, or m – but keep units consistent).
- Determine the starting temperature (usually room temperature, ~20 °C) and the maximum or minimum temperature the part will experience.
- Enter the values. The calculator uses the default α of 120e-6 /°C. If you have a specific grade’s datasheet value, you can adjust the formula manually (see below).
- Read the change in length and final length. If the result is positive, the part expands; if negative, it contracts.
For a custom α, multiply the current expression by (your α / 120e-6). For example, if your datasheet says 140e-6 /°C, use: len * 140e-6 * (t2 - t1). The calculator’s formula can be edited by the user.
Common Problems and Design Tips
- Seizing in bores: A PTFE bushing in a metal housing can seize if it expands more than the clearance. Design for the worst-case temperature difference, not the average.
- Buckling: Long, thin PTFE rods or tubes may buckle when heated if they are constrained at both ends. Use expansion joints or allow one end to float.
- Stress at interfaces: If PTFE is bonded to metal, the differential expansion creates shear stress. PTFE’s low modulus (about 500 MPa) means it deforms rather than transferring high stress, but repeated cycling can cause fatigue.
- Temperature range: PTFE is usable from about −200 °C to +260 °C, but α is not constant. At cryogenic temperatures, α drops; above 100 °C, it increases. For critical applications, consult the manufacturer’s data.
- Anisotropy: Molded PTFE can have slightly different expansion in the flow direction vs. transverse. Skived tape may behave differently from molded block.
Alternatives to PTFE
If thermal expansion is a problem, consider these materials:
- Filled PTFE: Adding glass fiber, carbon, or bronze reduces α to about 60–80 × 10⁻⁶ /°C, while retaining most of PTFE’s low friction and chemical resistance.
- PEEK: A high-performance plastic with α around 45–55 × 10⁻⁶ /°C, higher strength, and similar temperature range (up to 250 °C continuous).
- Polyimide (e.g., Vespel): α around 50 × 10⁻⁶ /°C, very stable at high temperatures.
- Metal or ceramic: For precision parts, metals have much lower expansion, but they lack PTFE’s non-stick and chemical properties.
For seals and bearings, you can also design with a spring or elastomer that accommodates the expansion, rather than changing the material.
Cost and Practical Considerations
PTFE is relatively inexpensive compared to PEEK or polyimide. Raw PTFE stock costs a fraction of PEEK, but the price difference narrows when you consider machining and design complexity. If you can tolerate the expansion with proper clearances, PTFE is often the most economical choice. If you need tight tolerances over a wide temperature range, the extra cost of filled PTFE or PEEK may be justified.
Remember that thermal expansion is only one factor. PTFE also creeps (cold flows) under load, which can cause dimensional changes over time. For precision applications, consider both thermal and mechanical effects.
Frequently Asked Questions
What is the coefficient of thermal expansion for PTFE?
The linear coefficient is commonly given as 120 × 10⁻⁶ /°C (or 120 μm/m·°C) for molded PTFE at room temperature. Some datasheets list 100–160 × 10⁻⁶ /°C depending on the temperature range and filler content. The volumetric coefficient is roughly three times the linear value, about 360 × 10⁻⁶ /°C.
Does PTFE expand more than aluminum?
Yes, significantly. Aluminum’s α is about 23 × 10⁻⁶ /°C, so PTFE expands roughly 5 times more per degree. For a 100 mm part heated by 60 °C, aluminum grows 0.138 mm while PTFE grows 0.72 mm.
How do I calculate expansion in two dimensions?
For area expansion, use ΔA = 2α × A₀ × ΔT. For volume expansion, use ΔV = 3α × V₀ × ΔT. These are approximations that hold for small strains (under 1–2%). For a 100 mm × 100 mm PTFE sheet heated by 60 °C, the area increase is about 2 × 120e-6 × 10000 × 60 = 144 mm².
Why does my PTFE part shrink when cooled below 19 °C?
PTFE undergoes a crystalline phase transition near 19 °C. On cooling through this point, the material contracts more than the linear formula predicts, and on heating it expands more. This is due to a change in the crystal lattice. For applications near or below 19 °C, use a datasheet that covers the actual temperature range.
Can I use this calculator for PTFE sheets and rods?
Yes, as long as you measure the length in the direction of interest. For a sheet, use the length or width; for a rod, use the length. The same α applies to all dimensions, so the expansion is isotropic in molded PTFE (neglecting anisotropy).
What is the difference between linear and volumetric expansion?
Linear expansion is the change in one dimension. Volumetric expansion is the change in total volume. For isotropic materials, the volumetric coefficient is approximately 3 times the linear coefficient. For PTFE, that gives about 360 × 10⁻⁶ /°C. Use volumetric when calculating how much a solid block displaces fluid or how much a cavity changes.
Related
Formula used
in len | Original length | mm | 100 | 0.1 in t1 | Starting temperature | °C | 20 | -273.15 in t2 | Ending temperature | °C | 80 | -273.15 out dl | Change in length | mm | len * 120e-6 * (t2 - t1) | 3 out l2 | Final length | mm | len + dl | 3 out strain | Strain (ΔL/L) | - | 120e-6 * (t2 - t1) | 5
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- ug to ppb Calculator: Convert Micrograms per Liter1.00 ppb
- Grams to Moles Chemistry: How to Convert0.2000 mol/L
- Convert ug/l to ppb Calculator
- CPP Calculator Ontario: How CPP Is Calculated162.12 $/month
- Grams to Moles to Molecules: How to Convert0.2000 mol/L
- Organic Chemistry Reaction Calculator: How It Works